That's a good question and the difference between the two SnapPad Jack Stand Pads for Motorhome are different shapes and depths, it isn't solely the notch in the center. I added photos of the two pads side-by-side so you can see the differences right next to each other. The correct pad will depend on the shape of your motorhome jack's feet:
- 10" Round Jack Feet: SnapPad EQ Compact Jack Pads - 10" Round Jack Feet # SP64FR4
- 10" Octagon-Shaped or 10" Round Concave Jack Feet: SnapPad... view full answer...
For their Companion series of 5th wheel hitches, B&W recommends using a 10 inch lube plate. I'd recommend the # 16721 from Curt. The lube plate would protect the skid on your hitch from getting scratched up, and would eliminate the need to use grease on the skid plate so you won't have a huge mess with grease everywhere. view full answer...
We have three Furrion access door replacements for their tankless water heaters. We have the 18 by 18 inch part # FR73FR, the 16 by 16 inch # FR43FR, and we have the 16 by 18 inch # FR63FR.
For the water heaters that match the door size we have the # FR98SR which has a 16 by 16 inch door, the part # FR68SR with is 18 by 18, and we have the # FR48SR which is 18 by 16.
The door size to go with comes down to what will work best on your RV as the rest of the assembly is the exact same. view full answer...
The correct front and rear TorkLift Camper Tie-Downs for your 2019 Ram 3500 Crew Cab long bed with a factory hitch will be one of two options, depending on if you have running boards or steps under your Ram's cab or not.
If you do NOT have running boards or steps, the correct fit is the Front TorkLift Custom Frame-Mounted Camper Tie-Downs # TLD2140 and Rear TorkLift Custom Frame-Mounted Camper Tie-Downs # TLD3112.
If you DO have running boards or steps under the cab of your Ram,... view full answer...
The correct replacement control center for your Progressive Dynamics Panel # PD4045KA for the lithium battery style you mentioned is the part # PD4045LICSV. LiFePO4 is a type of lithium battery and has different charging requirements. view full answer...
I have a solution for you, but the # BD1046130-00 is designed for a single speed electric jack. To replace landing gear with the motor 1046104 you'll want to use the Replacement Dual Output Motor for Bulldog Electric 5th Wheel Landing Gear # BD500359. This is the exact replacement part for your landing gear and was confirmed by my contact over at Horizon Global, who own Bulldog. view full answer...
For your 2018 Tesla Model 3 we have two Stealth hitch options. We have the part # 391TES317 which comes with a lower hitch opening that can only be used with a hitch accessory like a bike rack and we also have the part # 391TES317T which includes the same things plus all of the accessories needed to also tow a trailer like wiring and ball mount which hitch ball.
Essentially the # 391TES317T is the # 391CONVB5 plus the # 391TES317. view full answer...
Measure the diameter of the feet of your Power Gear setup and we'll be able to determine if the # SP64FR4 is a fit. This part number is for 10 inch diameter feet which is most likely what you have.
If you had 9 inch diameter feet instead you'd want the # SP54FR4, 7 inch # SP24FR4 11-1/2 inch or 12 inch part # SP84FR74, 8 inch # SP34FR4 etc. I attached a page to see all the options we have since there are quite a few. view full answer...
The Malone TopTier Load Bar Kit for Utility Trailers part # MPG493 fits 4' wide and 5' wide trailer decks so it would not be compatible with your 6 foot wide utility trailer.
The Malone Crossbar Conversion Kit for Standard Utility Trailer part # MPG475 will fit the 6'x8' utility trailer if it has an open frame with square rails.
view full answer...
For your horse trailer with Dexter Torflex 3500 lb axles, you will need the Torflex Lift Kit - Tandem Axle - 2-5/8" Lift # K71-707-02 along with two sets of the Dexter Axle Torflex #10 Axle Side-Mount Frame Installation Hardware Kit # DX54FR which will be welded to your trailer frame. I've attached some videos and a customer photo of the kits installed to assist. view full answer...
For your Furrion FGH3Z25BL (NO LONGER AVAILABLE) three-burner, propane cook top you will need to order the Furrion # C-FSRE21SA-SS-003 replacement stainless steel top with glass cover in order to get the glass. I contacted Furrion and they do not sell the glass only. view full answer...
We do have a replacement that will work for your 6-gallon Atwood water heater, with the best option being a tankless water heater from Fogatti, which comes with either a white or black door:
- White: Fogatti RV Tankless Water Heater - Gas - Automatic Pilot # LSB64FR
- Black: Fogatti RV Tankless Water Heater - Gas - Automatic Pilot # LSB44FR
The tankless heaters are really nice options because they conserve energy so well and give you immediate hot water, which is why they have... view full answer...
The correct way to determine which awning support arms you'll want to use you'll need to measure the bracket that the arms are attached to and attaches them to the side of the coach. The length of that bracket is the best indicator of the awning arm style you've got and will want to use as replacements- I've listed the options below for you to check out.
Short styles will measure 61-1/2" and use part # LC295743 (single arm) or # LC351829 (pair)
Pitched styles will measure 66-1/8" and... view full answer...
The BrakeBuddy Towed Vehicle Battery Charge Kit part # BB54FR comes with a the Brake Buddy Select 3 Portable Supplemental Braking System part # HM39524. I have attached a wiring diagram of how this is setup with the Brake Buddy. view full answer...
Great question!
From what I could find in the owner's manual for a 2015 Fiat 500 (looking both at the Recreational/Flat Towing and Emergency Towing procedures) it does look like you need to keep the steering wheel unlocked while flat towing. Since this means your ignition is on, it can very well drain your battery. I'm not sure why this isn't something that is commonly known because even some of our flat towing manufacturers don't have this info on their site. I reached out to Roadmaster... view full answer...
The Start Capacitor for Advent Air RV Air Conditioners part # ACMSCKIT is designed specifically for the Advent Air RV Air Conditioners like part # ACM150. The start capacity will bring down the starting amps for the air conditioner to 15 amps. view full answer...
I believe you are asking if the Go Power Overlander Expansion Kit - 190 Watt Solar Panel # 34282182 will work with the Go Power PWM Solar Charge Controller # 34276119, which is a 30 amp controller, and the answer to that is yes it will. It comes with everything needed to add the panel to your system.
Overall, this is compatible with a number of Go Power solar charging systems:
- Go Power Solar Elite Charging System - 380 Watt Solar Panels - 2,000 Watt Inverter Charger # 34282184
-... view full answer...
Yes, the Replacement 7" Monitor for Furrion Vision S Wireless RV Camera System # FR47FR is 100% compatible with your existing Furrion Vision S Wireless RV Backup Camera System # FOS05TASF and will make for a very nice upgrade.
Both the 5" and 7" monitors use the same power cord # C-FOS07TAPK-006 and suction cup mount # FR79SR, so you will still be able to use the ones you currently have. view full answer...
Thank you for the pictures. You are definitely correct that you need the Demco Hijacker Autoslide Locking Plate for MOR/ryde Pin Boxes # DM6025 to use the MOR/Ryde pin box with your Demco Hijacker # DM8550024.
The pictures that you sent in looks like your dealer just welded on some brackets of their own to lockout the Hijacker. If you notice the picture that I have attached the bracket from the Demco locking plate looks nothing like what they installed which is why you aren't seeing... view full answer...
The big difference is the corners of the main panel of the # FV807357 are cut out with small section to allow access to mounting hardware and the # FV807359 instead does not have this area cut out. So you'd want to look at your vents to see if you need the cutouts or not. view full answer...
The part number you mentioned from Coleman indicates you have a Coleman Mach RV AC unit which the part # MA00-325001 is a fit for. Compare this to the dimensional picture I attached as well.
The part # MA8335A5261 is for older models and could be what you'd need but you should be able to tell by looking at the two shrouds which style yours needs. This has dimensions of 13.8" high x 26" wide x 38" long. view full answer...
The Replacement Mounting Hardware part # LC701665 comes with the Extension Rods, Extension Rod Bracket, Torsion Arm Caps, and various hardware. I am not sure what all you have now but it sounds like you might also need the torsion heads, part # LC87FR for the idler side and part # LC34FR for the drive side. These also come with the roll tube as well.
I have attached a photo to assist. view full answer...
The Reese Titan Weight Dist Shank - Trunnion Only - 5-3/4" Drop, 8-1/4" Rise - 1,700 lbs TW # RP54977 is a fit for your system. The Blue Ox SwayPro Weight Distribution Shank for 2-1/2" Hitches - 9" Long - 9 Hole Adjustment # BXW4028, the Curt Weight Distribution Shank for 2-1/2" Hitches - 12" Rise - 8" Drop # C17132, the Equal-i-zer Weight Distribution Shank - 2-1/2" Hitch - 12" Drop # EQ34FR, and Equal-i-zer Weight Distribution Shank - 12" Long - 13" Rise, 9" Drop # EQ94FR are all options... view full answer...
In order to get power from your motorhome to your 2005 Jeep while you're flat towing you'll need a working 7 way with 12 volts. Since the front of your Jeep has a 4 way flat on it you will need to change out the plug because all 4 wires are being used. The tail light circuit won't have enough power to charge the battery and run the lights on your Jeep, however you won't be forced to rewire everything, just the plug on the front of the Jeep.
If you don't have 12V at the back of the 7... view full answer...
B&W indicated that you can use either 10" or 12" lube plate with the B&W Companion. The 10" is the most common size like part # RP83002 however the skid plate of the B&W hitch is wide enough to accommodate 12" lube plate part # RP83001 so you won't have an issue. view full answer...
You can certainly do that. You'll want to be sure to wire the pin on the vehicle side to correspond with the 12-v power supply pin on the 6-way motorhome trailer connector however. Some 6-ways use the center pin as the brake controller output, some use it as the 12-volt power feed, so you'll want to ensure both sides are wired the same way. Roadmaster offers a purpose-built circuit protected kit for this, part # RM-156-25.
Keep in mind that the circuit is capable of providing a maintenance... view full answer...
The Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers # PD4645V is a replacement for your Parallax Converter 6300 model 6345. The part number you mentioned is a lower amperage unit which is why it wouldn't work. view full answer...
We have just what you're looking for. The Manual-to-Electric Conversion Kit for HappiJac Truck Camper Jack Systems # LC733960-182524 is compatible with your HappiJac 4160 Series jacks and will allow you to convert your system from manual to electric.
I've linked a quick video for you to have a look at, as well. view full answer...
The replacement antenna for the Voyager WiSight Wireless RV Backup Camera Monitor # WVOM541AP is part # VO54FR on our site. If you're looking for the replacement antenna for the camera # WVCMS130AP instead then that would be part # PXXHD0006301R that you were looking at. view full answer...
Thanks for the photos, and from that it looks to me like you are asking if just the pitch arm assembly is available, and if so, the answer is yes, it is the Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm # LC375994.
This is just the pitch arm part of the entire arm assembly, the Solera 69" Standard Flat Awning Support Arm # LC281154 so you do need to be sure this is the arm assembly you do have, and if so the pitch arm I referenced is the correct replacement.... view full answer...
Integrated brake controllers are notorious for not always working well with electric over hydraulic actuators. Sometimes it's just easiest to replace the controller with aftermarket. What actuator does your trailer have?
If it is a Hydrastar like the # HBA16 then the adapter part # HBA-CAM is what you'd need. view full answer...
The Curt # C16024 fifth wheel legs you mentioned fit the A series hitches from 20k and up; the A20 # C16540, A25 # C16580, and A30 # C16590. They're technically designed for the A30 because of the legs's 30,000 pound rating but they still fit the other two. With that in mind they will not, however, increase the weight capacity of the other 2 hitches.
The # CU53FR legs fit all of the same hitches plus the Q Series and E Series hitches as well. These legs even fit the A30 however they... view full answer...
We do have the Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm - Black # LC375994 in a 63" version for you. We have it listed as part # LC67VR on our site! view full answer...
For the 17k Level Best jack replacements we have the part # LC359275 that you referenced. For 10k legs you'd instead want the part # LC359278. view full answer...
The B&W Biker Bar Motorcycle Tie-Down System Base with Anchor Plates # BWMC2300 does not need to be adjusted to the higher holes. The adjustability is dependent on the ground clearance of your frame. The B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301 shows adjustability as shown in the attached photo. view full answer...
In order to get the correct replacement support arm for your Solera awning, what you want to do is measure the wall mount of your awning. All you need to do is measure the length of that mount, and that measurement will let you know which support arm from the following options you need to get.
- 61 Inches - Black: Solera Short Awning Support Arm # LC295743
- 61 Inches - White: Solera Short Awning Support Arm # LC295742
- 66-1/8 Inches - Black: Solera Pitched Awning Support Arm... view full answer...
The Nissan Rogue underwent a design change model refresh for the 2021 model year, so a hitch and wiring can't be swapped from the 2018 model. So what you will need for a '21 Rogue is a new hitch and wiring that fits, and the best options are the following:
- Draw-Tite Max-Frame Trailer Hitch Receiver # DT85MR
- Curt T-Connector Vehicle Wiring Harness # C44ER
I really like the Draw-Tite because it has a nice concealed look that helps your Rogue maintain its streamlined look; I have... view full answer...
We offer a direct replacement for your current 45A Parallax/Magnetek 6345 Power Center. The Progressive Dynamics Replacement Converter, part # PD4645V is exactly what you'd need.
I've linked to a product description video for the # PD4645V replacement converter. view full answer...
The part 182496 is listed on our site as part # LC182496. It is the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems, and it does in fact come in a set of two. I've linked to a video review of these extension brackets for you. view full answer...
Here are the 2 different mounting options for installing the Batwing and Foxwing Awning Relocation Kit # RR31102. You can change the orientation of the brackets so that the awning will either hang higher or lower depending on your application. view full answer...
The Curt OEM Fifth Wheel Adapter Rails # C88KR fits the factory puck system on your 2021 GMC Sierra 2500 and supports the industry-standard rails, but I cannot confirm fitment with the B&W Patriot Slider Fifth Wheel Hitch # BWRVK3270. As you mentioned, other adapters state that it will not work with the Patriot Slider, so it may also be the case here. I contacted B&W and was told that they do not know of an adapter that will work. My contact at Curt told me that he cannot confirm fitment... view full answer...
I have a solution for you. In order for the Xporter Pro Shift # TH54RR to work on your 2021 Toyota Tundra is if you pair the Pro Shift with the Base Rails for Thule TracRac SR Sliding Truck Bed Ladder Racks # TH24RV. This is how you will be able to mount the Xporter with the tonneau cover you have pictured. Since the TracRac SR base rails install into your truck's stake pockets, you will be able to use the Xporter Pro Shift without interfering with the bed rails. Also, it is important to... view full answer...
The Reese M5 Series 5th wheel hitches, like part # RP30921, are designed to fit the Elite Series underbed rails that you mentioned installing on your 2016. Since it sounds like your 2020 GMC Sierra 2500 has the OEM pucks you will need to swap out your 5th wheel hitch entirely because the puck dimensions won't match up with this Reese 5th wheel hitch. You would instead need the # RP30890 which will fit the Chevy/GMC puck system.
The Demco Adapter Rails # DM6333 that you referenced will... view full answer...
The reason the assembly looks pretty new is because based on the motor 1101422 / 214-1001 you mentioned, your motorhome's steps were upgraded.
The only catch is you have to know when this upgrade occurred, which I realize is problematic for a used motorhome. But if this update occurred in 2005 or before you need a new step assembly. If it happened after 2005 we have exactly what you need with the Replacement Motor for Kwikee Electric RV Steps # LC379147 and Replacement Gear Box and... view full answer...
There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer.
A junction box/7-way plug kit like etrailer # e99011 is an option you have to convert the camper to match the 7-way RV blade type connector format. This avoids the extra connection points and potential trouble spots from using separate adapters. These items use different wire colors so be sure to follow the wiring guide for the specific kit you select.
The... view full answer...
Yes, the Replacement Head Pin for Solera Power Awning Gear Drive Head # LC93FR will fit on the idler head as well as the drive head. view full answer...
The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp # PD4060K is a confirmed replacement for your model 7355 that also has the box and circuit breaker panel.
If you simply want the converter replacement, then the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp # PD4655V is a direct replacement for the converter. view full answer...
This is a great question but what typically happens is that the glass develops tiny micro cracks that develop from hitting the glass several times combined with continual heating and cooling of the stress fractures which eventually leads to the glass just giving out.
We have the replacement steel top with glass cover for the Furrion ovens with part # C-FSRE21SA-SS-003. view full answer...
There is one lock set I really like the most that is going to give you the best overall protection for the 15,000 lb capacity Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls # C83WR:
- InfiniteRule Lock Set for Curt Rebellion XD Ball Mount # IR47FR
The reason I like the InfiniteRule locks the most is because they are not only made for the Rebellion, they are made of stainless steel and constructed to have a massive 42,000 lb shear strength. So there... view full answer...
I took a look at your order and saw you had purchased the Replacement Key Wall Control part # MA00A03550K but the issue you are having with your MaxxFan Model 4751KS is the circuit board, the Replacement Circuit Board part # MA10A04751KS so this what you need to replace. view full answer...
I am happy to explain why the yellow wire and blue wire are tucked away in the installation video of 7-Way RV Upgrade Kit for Trailer Brake Controller Installation part # ETBC7L. The ETBC7L is a kit used to install the Curt Echo Wireless controller part # C51180 which only requires a 12V power feed from the vehicle's battery and ground wire. The blue wire (which is used for brake output) is not needed because the Echo uses an internal sensor to sense when the vehicle's brakes are applied.... view full answer...
The Everchill Mounting Brackets # 324-000150 are used to mount Everchill RV Refrigerator w/ Freezer - 10.7 Cu Ft - 12V - Stainless Steel # 324-000119 in your RV. One bracket attaches to the top, and the other bracket attaches to the bottom of the refrigerator. I attached a photo to show you what it looks like with the top bracket in place. view full answer...
The etrailer Raised Side Rails for Roof Rack - Black Powder Coated Steel # e99034 are a great option for your 2019 Honda Odyssey. Next I recommend adding the Malone AirFlow2 Roof Rack - Aero Crossbars - Raised, Factory Side Rails - Aluminum - 58" Long # MPG216 and then you will be ready for your cargo box. The Yakima SkyBox 16 # Y07335 will fit well and the crossbars will need to be between 27-1/2 and 36 inches on center for proper support with this combination and you will need 52 inches... view full answer...
I suggest using the 7-Way RV Upgrade Kit part # ETBC7L and the Curt Echo part # C51180 because of the ease of installation and convenience. The Curt Echo Mobile Trailer Brake Controller just needs the basic trailer lighting functions and 12V power to be fully operational. Just wire the 12V black wire from ETBC7L to the vehicle's battery via the circuit breaker, ground the white wire and connect the 4 pin to the 4 pin portion of the plug shown in the picture I attached. The rest of the wires... view full answer...
I have a solution for you, but the # HU38FR is designed for the Portable Power Watchdog Surge Protector with Bluetooth - 50 Amp # HU47FR without the Emergency Shut-off feature. Your PWD50-EPO is the Portable Power Watchdog Surge Protector with Bluetooth and Emergency Shut Down - 50 Amp # HU87FR, so you'll need the Replacement Surge Module for Power Watchdog Surge Protector with Emergency Shut Down - 50 Amp # HU58FR. view full answer...
I do have an option for you but Lippert designed specific landing gear for the Keystone Montana. Other landing gear sets will not match up with the hangers on your trailer unless you weld on new hangers.
If you don't mind having your hangers moved by a certified welder, I recommend the Ultra-Fab Deluxe Electric Landing Gear Set, part # UF17-943010. This system has a lift capacity of 12,000 lbs with a 38 inch lift. each motor has its own toggle switch to make leveling the trailer that... view full answer...
Good question, and the difference between the standard Solera 12V Power RV Awning Conversion Kit # LC434724 (White) or # LC434723 (Black) and the Solera Smart Arm 12V Power RV Awning Conversion Kit # LC759405 (White) or # LC759517 (Black) is the latter's touchpad (pictured).
This touchpad allows you to control the awning along with the included switch, and it also allows you to use additional accessories, the Solera Smart Arm Wind Sensor Kit # LC715123, Solera Smart Arm Infrared Security... view full answer...
This is a great question, and one that I've seen before and have spoken with Lippert about previously.
In my discussions they've mentioned that the Solera Family Room # LC362231 (16 ft awning) or # LC362232 (17 ft) should not have any problems in normal wind conditions less than 20-25 MPH. The tan body panels are made from a heavy duty nylon cloth and the screen sections will allow a good deal of wind to pass through it when open, but I can see how during sustained windy conditions it... view full answer...
The HappiJac Qwik-Load Upgrade Kit for Standard Turnbuckles part # LC182894 is an excellent upgrade option for the HappiJac Original Turnbuckles for Camper Tie-Downs part # LC182898. These are going to cut down dramatically on the time it takes to secure the tie-downs. In regards to installation, you can either cut the hooks off your existing tie-downs or you can just go pick up some 1/2" all-thread at a home improvement store which is very cost effective and readily available.
Unfortunately,... view full answer...
You will need to add spacers, since you're right on the edge of the requirements, but the # F2366 would not be the correct size. Firestone has put together a chart/list that you can use to help you determine what kind of spacer you need. Since the distance between your brackets is 6-1/2", you should use the Firestone Lift Spacer # F2356 according to the chart/list below.
Distance between top and bottom bracket:
6-1/2" - 7-1/2" - Lift Spacer # F2536
7-1/2" - 8-1/2" - Lift Spacer #... view full answer...
I was able to confirm through my contact at Retrax that the T-channels on your 2019 Ford Raptor OEM tonneau Cover, model number VJL3Z84501A42A, share the same dimensions as the T-channels on the RetraxPRO XR Hard Tonneau Cover w/ Trax Rails # RTT-80373, confirmed to fit the same truck. This is true because Retrax helps to manufacture some of the components for the Ford tonneau covers.
With that in mind, the correct Rhino-Rack Vortex Crossbar System for your F-150 is # RRVA180B-RRRLT600,... view full answer...
To install the Curt Echo Brake Controller # C51180 on your 1999 Suburban with a 4-to 7 Pole adapter, like the one on our # ETBC7L 7-Way RV Upgrade Kit, you just need to plug it into the 7-Pole on the adapter. As long as it was installed correctly, and the rest of the connections were made, the adapter's 7-Pole will contain all of the trailer light functions that were originally on your 4-Pole flat connector, plus the additional functions for trailer brakes, 12V power, and reverse lights... view full answer...
You will want to measure the length of your current Solera awning pitch arms and match up the correct size on the link I attached for you. Based on the photo you attached, you will likely need one of the following sizes:
-Replacement Pitch Arm Assembly for Solera XL 63" Flat Awning Support Arm - Black # LC67VR
-Solera 66-1/8" Pitched Awning Support Arm, Black # LC266169
-Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm - Black # LC375994
If you can't... view full answer...
I can tell you how to easily determine the correct over/under conversion kit for your 2017 K-Z Sportsmen Classic 180THT, though we would not be able to verify a specific fit for any trailer. It's easy to determine the correct over/under lift kit though because all you have to do is measure the diameter of your trailer's axle.
- 2-3/8" Round Axle: Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00
- 3" Round Axle: Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00
I... view full answer...
In order to replace just the factory anti-sway bar bushings on a Ford F-53 Chassis you have a few options which will be based on the location of the anti-sway bar (front/rear) and the gross vehicle weight rating of the coach (15,700 lbs, 16,000 lbs etc.) or diameter of the factory sway bar (1-1/2", 1-3/8", or 1-5/8"). If you need bushings for a front anti-sway bar and it is 1-5/8" diameter then you can use the Roadmaster Polyurethane Bushing Kit part # RM-4139-127 but if you need bushings... view full answer...
I attached a link to a page that has install instructions for the Correct Track kit part # RR23QX that you referenced.
I'd recommend the shackle bolt kit part # MR58ZR as it comes with the correct size bushings, bolts, and shackle straps. view full answer...
Yes, you can upgrade the 4.3 inch monitor of your Furrion setup to the 7 inch # FR47FR or the # FR97FR for the 5 inch. This will work great and give you an easy to view monitor. view full answer...
You have a Dexter # 11 Torflex axle. Dexter offers a spacer kit as part # K71-724-02, but it's sold as a tandem axle kit only and isn't available for a single axle so you'd have some leftover parts you wouldn't need. If you don't mind the extra parts, this would work.
view full answer...
Yes we do. The correct rear cover you need is the part # LC289567 to match the front cover # LC643923 you referenced and the picture you sent in. view full answer...
The Replacement Breakaway System for Brake Buddy Classic and Select Supplemental Braking Systems part # HM39340 replaces the brake away switch for the brake buddy Classic II, Select II, Classic 3 (# HM39494), and Select 3 (# HM39524). We have not yet installed the breakaway switch from this setup yet to have a video to for assistance but I have attached the installation instructions for installing the break-away with the Brake Buddy system. view full answer...
The hangers will vary depending on the exact suspension set up from the manufacturer. With different spring combinations and number of axles used this will cause different parts to be required. These spring hangers are designed specifically for the Correct Track System as replacements for damaged parts.
Hanger # LC303918 is 5" tall.
Hanger # LC303917 is 4" tall.
If you are looking to change a suspension system to the Correct Track, their product line has been discontinued. I... view full answer...
We do have the kit you need to convert your A&E awning to a battery-powered Solera kit. You will not need to wire it to a power source and they even come with a charger, though you will get about 25 uses out of it before needing to re-charge the arms.
To determine if you can use this with your longer arms, the manufacturer has told us the best way to do so is by the fabric extension. So long as your awning when extended measures out less than 9 feet 8 inches then you will be able to... view full answer...
I've attached the photos of the instructions that come with the Trailer Valet XL Mounting Bracket # TVXLMB. It's a 2 page document, but hopefully it gives you a good idea of how it mounts and works with a Trailer Valet # TVXL2 or # TVXL25. view full answer...
It can indeed be used if the jack leg can accommodate the 1-1/4 inch width beetween the mount ears as shown in the provided photo. If the leg is too wide to fit in between the ears, they might fit inside the leg is the inside of the leg is greater than 1-3/4 inches. view full answer...
The 2019 Mercedes-Benz Sprinter 2500 could have been optioned with the factory trailer towing package and in which case it would have the plug for a brake controller which if present is located under the driver seat (see photo). If the vehicle was not optioned with factory trailer towing package then odds are you do not have the plug for a brake controller but it is always best to check for yourself to be sure.
If you do have the plug for a brake controller then I recommend using the... view full answer...
Yes, we have just what you were looking for. For the Pump Assembly only order the Dometic # DOM33FR. For the pump assembly and tank order Dometic # DOM46FR. Just click to add the parts you need to your online cart and at check out you will have several different choices for speedy delivery. view full answer...
I have a different option for you, but the Progressive Dynamics # PD4635LIV you were looking at is a replacement for the WFCO 8935 and not your WF-8735P.
Instead you will need the Progressive Dynamics # PD4135K which is designed to replace your WF-8735P and is compatible with Lithium Batteries like you were wanting.
I included a video of the # PD4135K for you to take a look at. view full answer...
Most R-Pods are going to have a torsion axle, and since yours is a 3,500 lb axle from Lippert that means you will have either a diamond torsion axle or a square torsion axle. To determine which axle you have - and thus which lift kit you need - take a look at the accompanying photo a customer sent in. This was from installing a lift kit on a diamond torsion axle, which will be oriented under the trailer in the shape of a diamond, as per the name of the axle. Otherwise the axle will be oriented... view full answer...
I have attached for you a set of photos which are used to identify the landing gear legs on a trailer. I assume you have either the older Lippert Ground Control 2.0 Leveling System or the newer Lippert Ground Control 3.0 Leveling System. If that is the case then the easiest way to tell which is which is to note the shape of the rear jacks. If the jacks are square then you have the Lippert Ground Control 2.0 Leveling System therefore need the Replacement Heavy-Duty Landing Gear Jack Leg... view full answer...
The Replacement Ball Assembly part # UF19-001057 for Ultra-Fab Gooseneck Tripod Stabilizer that can be used with the Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer part # UF19-950500 is a 2-5/16" ball.
We also carry the Ultra-Fab Gooseneck Trailer Tripod Stabilizer part # UF19-950450 that already comes with the 2-5/16" ball. view full answer...
Yes, the Advent heat strip part # ACMHD will work well with your Advent Air RV 13,500 BTU Air Conditioner part # ACM135. You will use the air distribution box to control the heat settings. view full answer...
There is actually no hardware that comes with or is needed to purchase separately for the etrailer Trailer Hitch Receiver # e98901 or its counterpart, the Curt Trailer Hitch Receiver # C13182, both of which fit your 2019 Jeep Grand Cherokee (the only difference being the black matte finish of the etrailer hitch vs. the glossier black of the Curt).
The reason why is that the hitch will install with existing bolts on your 2019 Grand Cherokee, as you can see by the accompanying cut out... view full answer...
It does sound like a motor and gear box issue, and so long as your steps are from 2006 or newer (there should be a sticker verifying the year on the motor) then we have exactly what you need with a new motor and and gear box/linkage for your 1101422 / 214-1001 motor:
- Replacement Motor for Kwikee Electric RV Steps # LC379147
- Replacement Gear Box and A Linkage for Kwikee Electric RV Steps # LC379160
If your steps are from before 2006 you would need to replace them, so I have... view full answer...
There isn't a full Advent Air Kit available that includes the Air Distribution Box # ACRG15 in place of the standard model, however you could piece together your own kit using the individual components. To match the contents of the Advent Air RV Air Conditioner Kit # ACM135CH you were looking at (except for the Air Distribution Box) you would just need part # ACM135 for the 13,500 Btu AC itself, # ACMHD for the Heat Strip, # ACMSCKIT for the Start Capacitor, and # ACRG15 for the upgraded... view full answer...
The 7 inch monitor, part # FR47FR is compatible with your # FOS43TASF Furrion Ovservation Camera system. as you can see in the provided photo, it does feature a speaker on the back side of the monitor. If you're using the suction cup mount, be aware that the 7 inch monitor uses a different mount than the 4.3. For the 7 inch, you'd need part # FR79SR. I've linked to product description videos for the monitor and the mount. view full answer...
You reported that you cannot use the remote on your MaxxFan 4700K to put the vent cover up and down. Let's troubleshoot.
Put some new batteries in your remote. Ensure that the display comes on. Verify if your vent cover now works. Verify if other remote functions work. If it is not your remote we can consider the following service parts.
First let's perform a reset. Disconnect the 12volt power source from the fan circuit board for two minutes then reconnect and test again. Many... view full answer...
The adapters which allow you to use factory brake controllers with electric over hydraulic brake actuators are not brand or make/model specific. Therefore you can use the HydraStar Electric Over Hydraulic Actuator Adapter Module part # HBA-CAM with the Dexter DX Series Electric Over Hydraulic Brake Actuator like part # K71-651 to work with a factory GM brake controller. view full answer...
If you go through our fit guide and select the brake controllers for your 2021 Toyota Tacoma, you can purchase the RedArc Tow Pro Elite # RED44FR and the plug and play harness # RED99FR together just by going to that page and adding the parts to your cart. However, the Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-007 is only sold separately at this time, so you would also need to go to that page and add it to your cart. view full answer...
The Air Lift WirelessONE Compressor System part # AL25980 will work just fine in very cold climates. However, you will need to either install the system inside the cab of the vehicle or install the system outside the cab and simply use some air brake anti-freeze when winter rolls around which is the option I recommend. I know Air Lift does extensive testing in colder climates so you should not have any issues with durability/longevity. I have attached a photo for you which further explains... view full answer...
I don't know what axles you have on your trailer but if you look at the axle tag it will tell you this. If you can't comprehend the axle sticker then just send me a photo of this and I will be happy to do that for you. There are a few different lift kits for torsion axle trailers but they vary by manufacturer and capacity. I have attached the options below:
Tandem Dexter #11 Torflex Axle (4,100 - 6,000 Lbs) # K71-724-02
Tandem Dexter #10 Torflex Axle (2,300 - 4,000 Lbs) # K71-707-02
Single... view full answer...
Curt has a fifth wheel bracket kit that fits your 2020 Chevy Silverado 2500HD without OEM rail kit with the part # C16429 or for a kit with rails part # C16429-204. view full answer...
Yes, the Lippert Components Heavy Duty Landing Gear Motor part # LC196308 would be a more dependable option than the Lippert Components High Speed Landing Gear Motor part # LC141893 that you have now. This motor has a higher weight capacity (6,500 lbs vs 5,000 lbs) therefore it does not have to work as hard to lift the trailer therefore will last longer. I will say however that it will be a bit slower (5400 RPM vs 7,140 RPM) but the longer life is a better feature to have than slightly... view full answer...
We have two basic styles of Lippert Hydraulic replacement jacks. We have the Kwikee level best style like part # LC359278 which has a 10,000 lb capacity or the # LC359275 for if you have a 17,000 lb capacity or we have the Level Up style like part # LC36VR and # LC26FR. Without more info from you the best solution I can provide is to check out the pictures of the jack legs I mentioned as well as what your jack legs look like to see what you'd need. Or send me pictures or part numbers and... view full answer...