Filter Questions and Answers:

reset filter
Custom Fit Vehicle Wiring
Custom Fit Vehicle Wiring
 

Expert Answers about Custom Fit Vehicle Wiring


  • Draw-Tite or Curt Trailer Hitch For 2021 Toyota Sienna
  • Let's start with the two trailer hitches you were referring to that fit your 2021 Toyota Sienna, which are the following: - Curt Trailer Hitch Receiver # C22UR - Draw-Tite Max-Frame Trailer Hitch Receiver # DT55MR They are very similar 2 inch hitches that are both easy bolt-on installations, but I recommend the Draw-Tite # DT55MR, for a couple of reasons. One is that it has higher overall capacities, which not only speaks to the strength of the hitch, but the higher tongue...
    view full answer...

  • Comparing Wiring Harnesses Available for the 2020 Honda Odyssey
  • I can see why this might be confusing and there are some differences between all 3 of these wiring harnesses. I'll start off by explaining the differences between the Tekonsha # 118781 and # 118753 wiring harnesses. The main difference is that the # 118753 is designed for vehicles that do not have the towing fuses already in place. In order to determine which one you can use on your 2020 Honda Odyssey you'll need to check the rear interior fuse box, which is located on the left side...
    view full answer...

  • Which Trailer Wiring Harness for 2020 Chevy Equinox
  • The wiring harness you meed will depend on whether or not you have the Premiers sub-model or not. For the Premier, you'd use # 118759 or # 118750 if it's not the Premier model. There's also a third less expensive possibility....if your Equinox has the factory tow package with the connector behind the bumper on the driver's side (see provided photo), you could use # 118285. The # 118494 you'd looked at is for an earlier model Equinox, and wouldn't work on your 2020 model.
    view full answer...

  • Recommendations for Hitch and Wiring Harness for 2020 Toyota Highlander Limited
  • I am happy to help you find the right setup to tow with your 2020 Toyota Highlander Limited. First, you need the Curt Hitch # C99FR which is a confirmed fit for all 2020 Toyota Highlander Trim types including your Limited package. Next, you need one of two wiring harnesses depending on whether or not your Highlander has a factory installed tow package. You can look under the rear bumper on the driver's side to find a quick connect (see picture below). I recommend the T-One 4 Pole Wiring...
    view full answer...

  • Correct Trailer Hitch and Wiring Harness for a 2021 Jeep Wrangler
  • Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver part # 76104 and T-One Vehicle Wiring Harness part # 118786 are both great options for a 2021 Jeep Wrangler. In regards to installation of the T-One Vehicle Wiring Harness, you can route the power wire over to the passenger side at the rear or front, it doesn't not matter and it will not have any affect on the system or install.
    view full answer...

  • Are There Different Instructions To Install the Curt T-Connector On a 2019 Honda Passport
  • The Curt T-Connector Vehicle Wiring Harness part # C56291 is a fit for both Honda Pilots and Honda Passports. The installation process of this harness on either vehicle will be almost the same save for a few of the rear trim panels being different which you have come to find out. If you are having trouble trying to remove the trim panels on a Passport then you can take a look at the instructions I have attached for you on the T-One Vehicle Wiring Harness part # 118809 which show this process...
    view full answer...

  • 4 Way Flat Vehicle Wiring Harness And Trailer Hitch Receiver For 2021 Toyota Sienna
  • 118824 is Tekonsha's part number for The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # TK69FR. We do not currently have an installation video for this wiring harness, but I can certainly help you out with this process. The harness has a connector that will plug into the trailer light connector in the trunk of your 2021 Toyota sienna; you will likely need to remove the trim panels and side cover to gain access to this connector. You will then need to connect the white...
    view full answer...

  • Difference Between Tekonsha 22114 and 22116 on Ford Transit T350
  • The OEM Replacement vehicle wiring harness with brake controller adapter part # 22114 is designed for 2015 - 2020 Ford Transit T350 with Single Rear Wheels and a 148" Wheelbase. While the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter - 7 Way Trailer Connector part # 22116 fits the 2015 - 2020 Ford Transit T350 without the single rear wheels. You want to purchase the correct wiring harness based off of this information. Both harnesses will give you a 7-way...
    view full answer...

  • Comparing the Trailer Wiring Harnesses for a 2019 Honda Odyssey
  • There are currently three trailer wiring harnesses available for your 2019 Honda Odyssey; the Curt T-Connector Vehicle Wiring Harness part # C56382, the T-One Vehicle Wiring Harness with Upgraded part # 118781, and the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118753. The fist two are non-powered harnesses which means you do not have to run a power wire up to the battery. The only down side of this is that this will limit the amount of lights you can power...
    view full answer...

  • Tekonsha 7-Way Wiring Harness vs. Curt 7-Way Wiring Harness for 2018 Honda Pilot
  • The difference between the 7-way harnesses available for your 2018 Honda Pilot comes down to quality and reliability. Over the years we have found the Tekonsha brand to be far more reliable than Curt so I strongly recommend the T-One Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer # 118286. This harness also has higher maximum amperage than the Curt which means it offers you better protection against potential shorts. To mount this to the Draw-Tite Trailer Hitch # 75225...
    view full answer...

  • Recommended Toolbox with Aluminum Rolling Tonneau Cover for 2020 GMC Sierra 3500
  • There are limited solutions for the tool box and rolling hard cover. I recommend the UWS Truck Bed Chest - Secure Lock Under Tonneau Series - 8.85 cu ft - Bright Aluminum # UWS08297 or the UWS Truck Bed Chest - Secure Lock Under Tonneau Series - 8.85 cu ft - Matte Black Powder Coat # UWS08298. I then recommended the BAK Revolver X4 Hard Tonneau Cover - Roll Up - Aluminum and Vinyl - Matte Black # BAK74FR. If you aren't absolutely needing a hard tonneau, then the Access Toolbox Edition...
    view full answer...

  • Wiring Harness Recommendation for 2019 Nissan Pathfinder Without Tow Package
  • For ease of install, the trailer wiring harness I highly recommend for your 2019 Nissan Pathfinder without the tow package is the Curt T-Connector Vehicle Wiring Harness # C56281 because it does not require any type of splicing into your Nissan's wires and does not need a direct connection run to the battery, which is often the trickiest part of a harness installation. This harness will require the installation of a couple relays (as you can see in the accompanying photo) but remains...
    view full answer...

  • What wiring do you recommend for my 2020 Hyundai Santa Fe
  • For your 2020 Hyundai Santa Fe we have a couple of wiring options. These will both offer a 4 way flat trailer connector. They are almost identical they install the same, have the same power output and are designed to protect your vehicle should there be any shorts on the trailer. Of the two I recommend the Tekonsha. They always seem to be the most dependable when it comes to custom fit wiring for passenger vehicles. I'v linked both for you to check out. As well as an installation video. Curt...
    view full answer...

  • Does Trailer Hitch For 2021 Toyota Sienna Have Difference in Ground Clearance
  • There won't be a difference regarding ground clearance for either of the hitches that fit your 2021 Toyota Sienna, the Curt Trailer Hitch Receiver # C22UR or Draw-Tite Max-Frame Trailer Hitch Receiver # DT55MR. This is essentially the same hitch in many ways, though I do like the Draw-Tite # DT55MR over the Curt because of its higher capacities as well as its finish, which isn't as glossy and gives a more refined look. That said, both hitches have visible crosstubes are and going to...
    view full answer...

  • How to Determine if 2008 Toyota Highlander is Equipped with Factory Taillight Converter
  • Luckily, rather than trying to understand the VIN check, the easiest way to determine if your Highlander is equipped with the taillight converter is to get a quick peek at the 10-pin connector it would plug into. The connector is located under the dash, between the emergency brake pedal and the brake pedal, as shown in the provided photo. If there's nothing plugged into the connector, you'd want to use the # HM11141845, as the trailer wiring won't work correctly without a taillight...
    view full answer...

  • Recommended Trailer Wiring Harness for a 2019 Hyundai Santa Fe Without Tow Package
  • Yes, the T-One Vehicle Wiring Harness part # 118784 is a fit for all models of the 2019 Hyundai Santa Fe which includes the Sport and those with or without the towing package. The T-One Vehicle Wiring Harness offers plug and play installation as you can see in the attached video. In regards to mounting, you can use the safety chain loops as shown in the attached photo or you can use a more permanent solution with the Mounting Bracket 4-Pole Flat part # 18144 and the No-Drill Mount for Electrical...
    view full answer...

  • Trailer Hitch Receiver For 2021 Ford Bronco Sport
  • We do have a trailer hitch receiver that is a fit for the 2021 Ford Bronco Sport, and I verified with the manufacturer that the correct fit is the following: - Curt Trailer Hitch Receiver # C76HR The hitch is a complete bolt-on installation as well, so no drilling into your Bronco Sport's frame is needed. I have added a link below to the installation instructions for you to take a look at so you can see how simple the installation process really is. The only other thing I wanted...
    view full answer...

  • Which is Better Trailer Wiring Harness for 2017 Jeep Grand Cherokee Tekonsha or Curt
  • The Tekonsha harness part # 118727 is the better option for your 2017 Jeep Grand Cherokee over the Curt # C62VR. The Tekonsha has a higher amperage rating so it will be more resistant to damage from an accidental short and also has a reputation for being more reliable as well. I attached an install video for more info on the Tekonsha as well.
    view full answer...

  • Correct Trailer Wiring Harness for 2020 Chevy Equinox
  • If your 2020 Chevy Equinox is equipped with the factory tow package, the correct Curt harness is the T-Connector # C94FR. If you don't have the tow package (there isn't a factory connector already present at the bumper) you will instead want the Tekonsha T-One Harness # 118759, which plugs in-line behind the tail lights. Both options will provide you with a 4-Way connector to power a trailer's basic signal lights. If you still need a hitch I highly recommend the Curt # C77FR (as long...
    view full answer...

  • Recommended Trailer Hitch And Wiring for a 2019 Jeep Wrangler
  • For your 2019 Jeep Wrangler, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118786 which is a plug and play kit that does not require any splicing. I have attached an install video for you as well on a similar 2018 model if you need help. If you have not yet picked out a trailer hitch, I recommend going with the Draw-Tite Max-Frame Trailer Hitch Receiver part # 76104 because it offers the most capacity and the receiver tube opening is less recessed...
    view full answer...

  • Installation of Curt T-Connector on 2019 Toyota RAV4 Hybrid
  • Thank you for the kind words and the purchase of the Curt T-Connector # C56434 wiring harness for your 2019 Toyota RAV4 Hybrid! Functionality-wise and install-wise the Curt T-Connector # C56434 and the Tekonsha T-One # 118801 are the same (so you can reference the linked T-One install). The differences between them are that the T-One has higher amp ratings (5 amp stop/turn and 7.5 amp tail) than the T-Connector (3 amp stop/turn and 6 amp tail) and the T-Ones historically have a more...
    view full answer...

  • Trailer Wiring for 2020 Ford Explorer Without Factory Trailer Wiring
  • The T-Connector for the 2020 Ford Explorer without factory tow package part # 118599 is the part you need for your application. This T-Connector is a plug and play option. In addition to the T-connector, if your vehicle doesn't have the tow package you need a trailer hitch. Part # CU78FR works for your application. This hitch is great because it is concealed under the bumper and only the receiver tube is visible. If you haven't already bought a ball mount, I highly recommend part...
    view full answer...

  • How To Install Both 4 and 7-Way Trailer Connectors On a 2019 Chevy Express Van
  • In order to install both a 4 and 7-way trailer wiring harness on a 2019 Chevrolet Express Van I recommend starting with the Hopkins Plug-In Simple Vehicle Wiring Harness part # 31345 which is plug-in-play. Then, you can convert this to a 7-way with 4-way using the Adapter 4-Pole to 7-Pole and 4-Pole part # 37185. Once you also get the Curt No-Drill Bracket part # C57202 you'll have everything.
    view full answer...

  • Redarc Tow-Pro Elite vs. Curt Spectrum Brake Controller for 2019 Audi Q5
  • On the surface, there is a lot of similarities between the Curt Spectrum Trailer Brake Controller # C51170 and the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR, but the Redarc is truly the superior option in every way for your 2019 Audi Q5. Since you don't have trailer wiring in your Audi you will need to add Vehicle Wiring Harness # 119190KIT and Universal Installation Kit for Trailer Brake Controller # ETBC7, though the Spectrum also needs the Wiring Adapter for Curt Trailer...
    view full answer...

  • Correct Trailer Wiring Harness for a 2021 Toyota Highlander With or Without Tow Package
  • The correct trailer wiring harness for a 2021 Toyota Highlander without factory tow package is the Curt T-Connector Vehicle Wiring Harness part # C76CR which plugs in behind the taillights. The correct trailer wiring harness for a 20021 Toyota Highlander with factory tow package is the T-One Vehicle Wiring Harness part # TK74FR which plugs into the tow package port. If you are not sure whether or not you have the factory tow package you'll want to reach out to the dealer but this is almost...
    view full answer...

  • Why Does the Trailer Wiring Harness For a 2019 Hyundai Tucson Require a Power Wire
  • The T-One Vehicle Wiring Harness part # 118812 which is a fit for a 2019 Hyundai Tucson does require a wire to be run to the vehicle's battery for power. The reason for this is because the vehicle's tail light circuits are not rated high enough for the additional amp draw of the trailer lights. Furthermore, this acts as a barrier to protect the vehicle' tail lights if there were ever an issue with the trailer's lights. In regards to other trailer wiring harnesses that don't require a...
    view full answer...

  • What Trailer Wiring do you Recommend for my 202 KIA Telluride
  • For your 2020 Kia Telluride we have a couple of wiring options. These will both offer a 4 way flat trailer connector. They are almost identical they install the same, have the same power output and are designed to protect your vehicle should there be any shorts on the trailer. Of the two I recommend the Tekonsha. They always seem to be the most dependable when it comes to custom fit wiring for passenger vehicles. I'v linked both for you to check out. As well as an installation video. Curt...
    view full answer...

  • Comparing the Tekonsha and Curt Trailer Wiring Harnesses for a 2020 Hyundai Palisade
  • The trailer wiring harness I recommend for a 2020 Hyundai Palisade is the T-One Vehicle Wiring Harness part # 118784 over the Curt T-Connector Vehicle Wiring Harness part # CU94FR. The main reason for this is that the converter box is physically smaller therefore easier to mount. Furthermore, the T-One Vehicle Wiring Harness has been more reliable than the Curt T-Connector Vehicle Wiring Harness historically speaking.
    view full answer...

  • Recommended 7/4-Way Trailer Wiring Harness for 2020 Toyota Sienna XLE
  • The trailer wiring harness I recommend for a 2020 Toyota Sienna XLE is the T-One Vehicle Wiring Harness part # 118648 as it is a plug-n-play fit and our most reliable option. That said, this harness only has a 4-way but that's all that is available for this vehicle. However, you can convert this to a 7-way using the 7-Way RV Upgrade Kit for Trailer Brake Controller Installation part # ETBC7L which comes with both 4 and 7-way connection points. Please note, if the trailer has brakes then...
    view full answer...

  • Are Relays Required When Installing T-One Wiring Harness on 2019 Nissan Pathfinder
  • I know it seems like there are extra steps to take for installing the T-One # 118273 on your 2019 Nissan Pathfinder but it all just boils down to this; without those relays installed the T-One won't receive any power. Basically these act as fuses so without a fuse the circuit is dead. I'm not sure why Nissan decided to locate the plug in the rear hatch area but that's where it sits on your Pathfinder. If you had the factory tow package you'd be able to go to that same location and see a...
    view full answer...

  • How to Determine if a 2019 Toyota Highlander Has a Tow Package
  • Basically what it boils down to is that if you have the tow package you'll already have a 4-Way trailer wiring connector on your 2019 Toyota Highlander so if you don't already have one odds are you need a wiring kit with the converter like the Curt # C56217, Tekonsha # 118449, or Hopkins # HM11141845. The other way to tell is to check and see if there is already a converter on the wiring harness in the rear hatch area. If you check out the attached picture you can get an idea of where...
    view full answer...

  • Recommended Trailer Wiring Harness for 2011 BMW X3 28I
  • For your 2011 BMW X3, the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT is a great choice if you don't want to splice into your vehicle wires, but it is more expensive due to the zero contact interface sensors. If it were me, I'd use the Upgraded Heavy Duty ModuLite Circuit Protected Vehicle Wiring Harness with Installation Kit # 119190KIT confirmed to fit your vehicle and use the quick splice connectors on the factory wires....
    view full answer...

  • How Does 7-Way and Brake Controller Install in 1973 Ford F-350
  • For a truck as old as yours it would be pretty hard to find a wiring diagram for installing the 7-way part # 20023 but I can help you figure it out using a circuit tester like the part # PTW2993. Basically you are going to need to test all of the wires of your taillights to determine their function and then wire to the 7-way using the included diagram. Now hardwiring in a brake controller will be a similar process but you'll only have to test the wires at the brake switch till you find...
    view full answer...

  • Wiring Harness for 2019 Toyota RAV4 Hybrid
  • There absolutely is a wiring harness for a 2019 Toyota RAV4 hybrid, the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118801. This will be a perfect harness to pair with the Draw-Tite Max-Frame Trailer Hitch R # 76201 so you can tow with your RAV4 hybrid. I have added links to video installs of both the harness and hitch on a '19 RAV4 that you can check out.
    view full answer...

  • Wiring Harness and Hitch Recommendation for 2016 Mazda CX-9
  • The term 'Towing Package' is pretty useless because it's an extremely vague description whose meaning varies from vehicle manufacturer to vehicle manufacturer, and even among different models from the same manufacturer. For the sake of this discussion in terms of a wiring harness, Tekonsha uses the term 'tow package' because there is a single, dedicated connector for connecting a trailer harness, rather than installing inline where the factory taillight harness connects to the taillight...
    view full answer...

  • Recommended Wiring Harness and Hitch For 2019 Chevy Bolt
  • For a wiring harness on the 2019 Chevy Bolt I recommend the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit part # 119250KIT which is a clamp on style wiring harness. There is not a custom plug and play option available for the Chevy Bolt but the wiring harness clamps to the vehicle wiring instead of splicing in so this is your best option. If you need a hitch, I recommend Draw-Tite Sportframe Trailer Hitch Receiver part # 24956 which...
    view full answer...

  • Installing Hopkins 4-Way/7-Way Wiring on a 2016 Chevy Colorado
  • Yes, the Hopkins 7-Pole and 4-Pole Trailer Connector Sockets w/ Mounting Bracket and Wiring # HM40975-11998 is in stock. Installing this on a 2016 Chevy Colorado should take no time at all (maybe 20 minutes tops if you aren't familiar with it?) because all you have to do is replace the knockout plug in the bumper with this connector and then splice in the wiring harness to the OEM wiring on the driver's side of the bumper. Since this wiring will be out in the elements I recommend using...
    view full answer...

  • Comparing the Trailer Wiring Harnesses for a 2020 Honda Odyssey
  • There are three trailer wiring harness options for a 2020 Honda Odyssey, the T-One Vehicle Wiring Harness part # 118781, the T-One Vehicle Wiring Harness part # 118753, and the Curt T-Connector Vehicle Wiring Harness part # C56382. The T-One Vehicle Wiring Harness part # 118781 is what I recommend because when compared to the T-One Vehicle Wiring Harness part # 118753 comes with additional fuses that may or may not be needed to activate the tow package. If you want to check the fuse box;...
    view full answer...

  • Which Vehicle Wiring Harness Fits A 2021 Kia Sorento SX Without The Factory Tow Package?
  • For your 2021 Kia Sorento SX without the factory tow package you will need the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # TK26FR which is confirmed to fit all models of the Sorento including your SX model. At this time (6/15/2021) this is the only plug in adapter that will not require any splicing into your factory wiring. The Curt # C59236 will also work but requires you to splice into your factory wiring. I included a link to the written instructions of...
    view full answer...

  • Recommended Trailer Wiring Harness 2019 Nissan Frontier
  • Thanks for being a returning customer. The Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors # HM43534 will require additional parts for compatibility with your 2019 Nissan Frontier. Because of this I recommend the T-One Vehicle Wiring Harness with 7-Way Trailer Connector # 118266 which will give you all the parts you need and then if you want to change out the 7-way for a 7-way with 4-way connector you can use the Hopkins Endurance...
    view full answer...

  • How to Tell if 2019 Kia Sorento is Equipped with Factory Tow Package
  • Absolutely, you can check just behind the rear tire on the driver's side of your 2019 Kia Sorento, on the outside of the frame rail. The factory connector, if present, will look like the one in the attached photo (B). Note that you will need to remove a protective cover to gain access to the Sorento's wiring harness (C). Take a look at the video I attached. Around the 0:35 mark, it shows how this cover is removed and where the Kia connectors are located. If you find that you do...
    view full answer...

  • Parts Needed to Add 7-Way to 2018 Ford Transit T350 Without Factory Connector
  • Yes, the Tekonsha OEM Replacement Vehicle Wiring Harness ith Brake Controller Adapter - 7 Way Trailer Connector # 22114 is exactly what you need to add a 7-way for a brake controller on your 2018 Ford Transit T350 without the factory trailer connector. This kit will fit all of the single rear wheel models of the T350, regardless of wheelbase, including your 148 inch wheelbase. It does not require circuit breakers because the kit comes with fuse holders and fuses that attach between the...
    view full answer...

  • Adding 7-Way to 2020 Honda Pilot for Trailer Towing
  • We have the T-One Wiring Kit # 118286 from Tekonsha which comes with everything you need to install a fully-functioning 7-Way connector on your 2020 Honda Pilot. Then for a brake controller I highly recommend the Tekonsha Prodigy P3 # 90195 which installs to the plug under your driver's side dash with the adapter # 3070-P. I have attached an installation video of this wiring kit on a 2020 Pilot and a review video of the P3 for you to check out. If you don't already have a trailer...
    view full answer...

  • Recommended Trailer Wiring For 2020 Jeep Grand Cherokee Without Tow Package
  • For your 2020 Jeep Grand Cherokee I recommend the Tekonsha T-One Vehicle Wiring Harness part # 118727. It's custom made for your Jeep and it gives you a 4 way flat trailer connector so you have all the lights to tow a trailer safely and legally. It gives you your tail light functions, turn signals, and brake lights. The wiring installs behind your tail lights and plugs inline between the factory connector and the light assembly. There is no cutting or splicing of the factory wires, however...
    view full answer...

  • Is Curt T-Connector Wiring Harness Safe to Install on 2019 Volkswagen Tiguan
  • If you are concerned with keeping the OEM wiring safe on your 2019 Volkswagen Tiguan then the Curt T-Connector # C56403 that you are looking at is actually the perfect solution! Yes it does tee in with the tail lights on your Tiguan but those basically just act as triggers. Since this wiring harness draws power directly from the battery on your VW and it uses an integrated module (the black box) so if anything were to become damaged from your trailer the ModuLite would stop it. The only...
    view full answer...

  • Are Extra Relays or Fuses Needed to Use Curt Trailer Wiring Harness on 2020 GMC Terrain
  • I can understand how the wording could be confusing on whether or not the Curt # C94FR (56429) will work on your 2020 GMC Terrain, but I can confirm that it will indeed work for you without needing to install any extra fuses or relays on the vehicle. The "with tow pacakge" selection on our site, refers to having the factory harness behind center of the rear bumper, like you mentioned having. According to my contact at Curt, this is present on all 2020 GMC Terrains, which is why they...
    view full answer...

  • Installation of Trailer Wiring Harness on 2020 Honda Pilot
  • Installing a trailer wiring harness on your 2020 Honda Pilot can seem intimidating, but it really is not as complicated as it might seem at first glance. First, let's start with the right harness, and I highly recommend the T-One Vehicle Wiring Harness 4-Pole Flat Trailer Connector # 1187600 if your trailer only has a 4-way or T-One Vehicle Wiring Harness 7-Way Trailer Connector # 118286 if your trailer has a 7-way. These are not only the easiest installs but they are also the most reliable...
    view full answer...

  • Recommendation for Adding 5-Way Trailer Connector to 2019 Mazda CX-9
  • On your 2019 Mazda CX-9 there is a factory port behind the passenger side trim panel that accepts a custom 4-Way trailer harness plug. If this is what you are referring to when you mentioned that your vehicle has the trailer ready connector, then you will want to start with the Tekonsha T-One Wiring Harness # 118278. This will plug right into that factory port to provide you with a 4-Way connector. From there (or if you already have the 4-Way connector) I recommend simply adding the...
    view full answer...

  • 7-Way, Trailer Hitch, and Brake Controller for 2019 Subaru Ascent
  • For your 2019 Subaru Ascent we have the 7-way kit part # 118290 which is a confirmed fit and installs with minimal wiring since it ties into factory wiring. The Draw Tite hitch part # 76253 has a bracket to the left of the hitch opening that a 7-way can attach to. You can use a bracket like the # C67UR to attach to the 7-way of the # 118290. Then for a brake controller the Redarc Tow Pro Liberty part # RED24FR would be a really great choice as it's mostly out of main view, is proportional,...
    view full answer...

  • Installing 7-Way Trailer Connector so It Doesn't Get Destroyed Backing out the Driveway
  • Here's what I'd recommend. If you have an exposed portion of the hitch crossbar to work with, use the # 18136 no drill bracket. This fastens to the hitch crossbar using an included pipe clamp. You'll also use the # PK12711U 7-way mounting bracket. I'd begin by mounting the trailer connector to the # PK12711U, so that the mounting flange is at the bottom. Then, attach that to the # 18136 but just leave it finger tight for the moment. Put the # 18136 up against the underside of the hitch...
    view full answer...

  • Recommended Fifth Wheel Wiring Connection for 2019 Ford F-350 Super Duty
  • You are correct, there are two Bargman 5th wheel wiring harnesses for a 2019 Ford F-350, and the correct harness will depend on if you have the Fifth Wheel Towing Package in your truck. The fifth wheel towing package means your truck has the puck system for mounting a fifth wheel hitch like the B&W Companion 5th-Wheel Hitch for Ford Super Duty Prep Package # BWRVK3300. The Bargman 5th Wheel/Gooseneck 90-Degree Wiring Harness # 54701-007-010 is the recommended harness if your 2019 Ford...
    view full answer...

  • Does Curt 7-Way Wiring Harness Fit 2019 Ford Ranger
  • The Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector # C56431 will absolutely fit the connector you have on your 2019 Ford Ranger. If you take a look at your photo as well as the accompanying photo I added from the install video of this harness on a Ford Ranger, you can see the connectors are exactly the same. I do recommend checking out the linked video install of the Wiring Harness # C56431 so you can see how easy it is. I also strongly recommend using Dielectric...
    view full answer...

  • Fifth Wheel Wiring Harness Recommendation for 2020 Ford F-350 Super Duty With Prep Package
  • The recommended fifth wheel/gooseneck wiring harness for your 2020 Ford F-350 Super Duty with the factory prep package is the Bargman 5th Wheel/Gooseneck 90-Degree Wiring Harness for Aluminum Truck Bed # 54701-007-010. The reason for that is when I have contacted Bargman about this issue in the past, they told me that while the other harness, part # 50-97-410-010, will work with a Ford F-350 with the fifth wheel prep package, there have been very, very rare occasions where it can read...
    view full answer...

  • How to Install 7-Way Connector on 2019 Subaru Outback Wagon
  • We have exactly what you need to install a 7-Way connector on your new 2019 Subaru Outback Wagon so you can connect with the 7-Way on your trailer. You will need to start with a 4-Way harness and for this the Tekonsha T-One # 118467 will work perfectly. This custom harness will plug right into a factory port behind the driver's side trim panel for a completely "plug-and-play" installation. I have attached an installation video that you can even use for reference. Then once you have...
    view full answer...

  • Does 4-Way Wiring Harness Fit 2018 Toyota Tacoma Without Factory Tow Package
  • You can absolutely add the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118685 to your 2018 Toyota Tacoma that does not have the factory tow package. Installing this connector in your truck will only require you to plug it into connection points behind your taillights and run a hot lead to your battery like in the linked installation video I added for you. Additionally, I also highly recommend using Dielectric Grease for Electrical Connectors # 11755 to help prevent...
    view full answer...

  • 5th Wheel 7-Way Kit Recommendation for 2020 Ford Super Duty Cab and Chassis
  • We have 5th wheel trailer wiring kits that fit your 2020 Ford F-350 Cab and Chassis like with the part # C57008 but the part number you referenced does not fit your truck. The # C57008 does not install to the connectors you sent in a picture of though. These plug inline with the 7-way connectors at the rear of your truck.
    view full answer...

  • Recommended Trailer Wiring To Add 7-way to 2020 Honda Passport
  • Maria, It is possible to put a 7-way on the 2020 Honda Passport with factory tow package with Tekonsha wiring part # 118291. This wiring harness will plug into the factory OEM port under the bumper and give you a 7-Way plug at the rear of your Passport. It includes all of the required fuses to activate the tow package. You will need the mounting bracket part # PK12711U and Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long part # C57202 to mount...
    view full answer...

  • How To Tell If a 2020 GMC Terrain Has the Factory Tow Package for Trailer Wiring
  • In order to determine if a 2020 GMC Terrain has the factory tow package you will need to take a look in the rear fuse box on the driver side of the vehicle. In the fuse box there will be two locations you need to check, K2 and K3 which are for the trailer lights. These slots should be empty but what we are looking for is silver terminals inside each of the holes for the prongs on the relay. If there are silver terminals then you have the factory tow package but if not then you do not have...
    view full answer...

  • What Wiring do you Recommend for my 2020 Hyundai Palisade
  • For your 2020 Hyundai Palisade we have a couple of wiring options. These will both offer a 4 way flat trailer connector. They are almost identical, they install the same, have the same power output and are designed to protect your vehicle should there be any shorts on the trailer. Of the two I recommend the Tekonsha. They always seem to be the most dependable when it comes to custom fit wiring for passenger vehicles. I'v linked both for you to check out. As well as an installation video. Curt...
    view full answer...

  • Difference Between Wiring Harnesses for 2019 Mazda CX-5
  • Between the two wiring harnesses that fit your 2019 Mazda CX-5, Tekonsha # 118746 and Curt # C56377, I recommend the Tekonsha. It has a higher maximum amperage than the Curt. Another reason I recommend the Tekonsha is simply because we've always had better success with their reliability. I also prefer how the Tekonsha's converter box actually uses a screw to anchor it in place where the Curt's is just doublesided tape.
    view full answer...

  • Trailer Wiring Harness That Fits 2019 Ford Edge
  • You are correct, the Curt T-Connector Vehicle Wiring Harness # C56272 is not a fit for a 2019 Ford Edge; this harness is only a fit for 2015-2018 Ford Edge SE and SEL models; whoever told you it did fit your vehicle was mistaken. We carry the correct wiring harness for your 2019 Ford Edge, depending on the model. - 2019 Ford Edge SE or SEL: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C89FR - 2019 Ford Edge Titanium: Curt T-Connector Vehicle Wiring...
    view full answer...

  • Connecting Brake Controller Wiring on 2019 Chevy Express Van 3500
  • Thank you for all of the information and pictures! It looks like you should at least have some wiring already run on your 2019 Chevy Express Van 3500 so I'm just as confused as to why you don't have a round plug with a cap inside the driver's side frame rail or blunt cut wiring in the jack storage compartment. Aside from double checking and having someone else check as well (to get a pair of fresh eyes on your vehicle), the only other thing I can really offer is to just run your own wiring...
    view full answer...

  • Does 7-Way Wiring Harness Fit 2020 GMC Acadia Without Factory Tow Package
  • The Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector # C56326 will just plug into the back of your 2020 GMC Acadia and give you a working 7-way even though you do not have the factory tow package. There is not going to be any need to run any wires or do anything other than plug the connector in. I have added a link to the installation instructions as well as a link to a video install for you to check out of the Curt T-Connector Vehicle Wiring...
    view full answer...

  • Is a Relay Required for a Wiring Harness on a 2020 Acura MDX
  • While you are correct that a wide variety of trailer wiring harnesses do require the installation of a relay, this is not the case for your 2020 Acura MDX. I recommend going with one of our Tekonsha wiring kits because we have found that their converter boxes tend to be the most reliable. For a 4-Way plug you need the T-One # 118628 but for a 7-Way plug you need the T-One # 118289 for a 7-Way plug. It is worth noting that even though you don't install any relays, you do need to install...
    view full answer...

  • What Is the Best Trailer Wiring Harness Option for 2020 Honda Odyssey
  • As long as your 2020 Honda Odyssey doesn't fall into the extremely rare category of Odysseys that are missing terminals on fuse locations #10, #11 and #12 inside the fuse box, your best option is to go with the Tekonsha # 118781. Curt offers a similar option with the # C56382, but in our experience, the Tekonsha harnesses, and their converter boxes in particular, seem to do a better job and have proven to outlast the competition. If you want to be extra sure, you can look behind the...
    view full answer...

  • Parts Needed to Upgrade 4-Way to 7-Way and Add Brake Controller to 2006 Nissan Xterra
  • Since you already have a 4-Way on your 2006 Nissan Xterra you already have the relay harness that comes with the Curt T-Connector # C56226 so you just need the wiring for the 7-Way which is found as part # 118267. Please note that the gray plug that carries the additional functions of the 7-Way may or may not match up with what is on your vehicle. For some reason Nissan wasn't consistent with what plug they used on your vehicle and so sometimes it can be hit and miss but all you need to...
    view full answer...

  • Recommended Trailer Wiring Harness for 2020 Toyota RAV4
  • I'd recommend going with the Tekonsha # 118801, which would install as shown in the video I've linked for you. The Tekonsha harness is rated for more amperage than the Curt model, which I why I recommend it.
    view full answer...

  • Trailer Wiring Harness Recommendation for 2021 Hyundai Tucson with LED Taillights
  • The Curt trailer wiring harness part # C89KR is a fit for your 2021 Hyundai Tucson with LED taillights but I would actually recommend the Tekonsha part # 118812 as it has a more reliable converter box.
    view full answer...

  • Trailer Wiring Harness That Fits 2021 Kia Seltos
  • The trailer wiring harness that fits your 2021 Kia Seltos is the Curt T-Connector Vehicle Wiring Harness # C89KR. Along with the wiring harness, the trailer hitch that fits your '21 Seltos is the Curt Trailer Hitch Receiver # C65FR. It sounds like you are planning to do some towing so you will also need the Curt Class II Drawbar # C45521 with Trailer Hitch Receiver Lock # C23517 or Pin and Clip # F-4 to secure it to your hitch. For a hitch ball you will need either 1-7/8" Hitch Ball...
    view full answer...

  • Tekonsha or Curt Wiring Harness for a 2017 Chrysler Pacifica Touring L
  • I recommend going with the Tekonsha T-One # 118712 over the Curt T-Connector # C56322 for your 2017 Chrysler Pacifica Touring L simply because it has higher amp ratings and we have found the Tekonsha wiring products in general to be the most reliable on the market. If you don't already have a hitch then I recommend the Draw-Tite # 76046 because it has a hidden crosstube and a mounting bracket you can use with part # 18144 for a very clean look and a way to have the 4-Way connector at...
    view full answer...

  • Recommended Wiring Harness For 2020 Toyota Tacoma Towing A Trailer
  • If you are just looking to tow a trailer with lights and without brakes I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118685. This will give you a 4-Pole flat on the back of the Tacoma to tow a trailer with lights. The Tekonsha brand wiring has proven to be more reliable than the other brands and has the highest rated amp capacity so it can handle a little more power. It plugs into the tail light assemblies on the truck so it is a very straight...
    view full answer...

  • Does Curt Wiring Harness 56256 Fit 2019 Kia Sorento Without Factory Tow Package
  • Yes it will! The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56256 is a fit for your 2019 Kia Sorento that does not have the factory tow package. That said, I do highly recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118583 instead because we have found these to be the most reliable wiring harnesses. I have added links to video installs of both wiring harnesses for you to check out. Additionally, if you need...
    view full answer...

  • How Can I Tell if My 2013 Nissan Pathfinder Came With Factory Tow Package
  • All 2013 Nissan Pathfinders came pre-wired for a tow package, so we know your Pathfinder at least has something. If your Pathfinder came with the tow package option from the dealer, then you would have a trailer hitch and trailer wiring at the back of the Pathfinder. Since you are asking for a wiring kit, I'm guessing you need the wiring still. For this I recommend the Curt 7-Way Wiring Harness, # C56357, if you want a 7-pin trailer connector or the Curt 4-Way Wiring Harness, # C56281,...
    view full answer...

  • Recommended 7-Way Trailer Connector and Brake Controller for 2019 Honda Odyssey
  • To set your 2019 Honda Odyssey up to pull your trailer that is equipped with electric brakes you will need to start with a 4-Way trailer harness. For this the Tekonsha T-One # 118781 will work perfectly. This custom harness will install by plugging right into the factory port behind the interior trim panel in the rear cargo area (see attached image). This particular harness features a higher amp rating than the Curt alternative that is also available for your Odyssey and also allows...
    view full answer...

  • 7-Way and Brake Controller Solution for 2018 Ford F-150 without Tow Package
  • Your 2018 Ford F-150 without the tow package and 7-way does have brake controller wiring currently so once you have the 7-way part # C56413 installed you'd be able to easily install a brake controller using the truck's factory wiring. The P3 part # 90195 and the install harness part # 22292 would be a really great and easy to install option. This is the most advanced and easiest to use brake controller on the market so I recommend it highly.
    view full answer...

  • Wiring Lance Slide In Camper to Work with In-Bed Trailer Connector on 2019 ford F250
  • Since the 7-way round pin plug is obsolete, your best bet would be to replace the connector on your camper with the common 7-way blade style connector. You'd remove the existing plug on your slide in camper, and replace it with # 54-77-003. You could then use an extension like # C56080 to reach the connector rearward of the wheel well.
    view full answer...

  • No Brake Lights with Hopkins Plug-In Harness On a 2013 Volvo XC70
  • There are two different sets of tail lights on a 2013 Volvo XC70, a pair in the quarter panel at chest height and a pair in the lower bumper at knee height. I took a look at all the trailer wiring harnesses for a 2013 Volvo XC70 (Curt T-Connector part # C56386, Tekonsha T-One part # 118774, and Hopkins Plug-In part # HM11143735) and these all show the connectors plugging into the tail lights at chest height (see photo). It sounds like you may somehow have them plugged into the tail lights...
    view full answer...

  • Does the Draw-tite Hitch for Honda Passports 76290 Come with a Wiring Harness
  • I have a solution for you, but the Draw-Tite # 76290 does not come with wiring; this is fairly commonplace since not everyone will need a trailer wiring harness with their hitch. With that said, I recommend using the Tekonsha # 118809, which is a confirmed fit on the 2019-2021 Honda Passport (the same as the Draw-Tite 76290). This provides you with a 4 way trailer connector that has a powered converter to help protect your vehicle's electronics from shorts and backfeeds on the trailer....
    view full answer...

  • How To Run the Power Wire for a Trailer Wiring Harness on a 2019 Toyota RAV4
  • I have great news for you. There has since been a plug-in trailer wiring harness released for your 2019 Toyota RAV4 Hybrid, the T-One Vehicle Wiring Harness part # 118801 so this is now what I would use along with the Curt Trailer Hitch Receiver part # C13416. In regards to routing the power wire, this will be up to you as the instructions do not specify an exact route for this. However, we have a help article that gives some really good pointers and I have attached this for you. Since...
    view full answer...

  • Recommended Flat Tow Wiring for 2018 Jeep Grand Cherokee Instead of Mopar Harness
  • If you are referring to the Mopar harness that fixes the steering stability issue, then it was resolved by Jeep starting with the 2018 models so you won't require it. For lighting, you can use a Mopar wiring kit if desired, but there are other options that will work well for your 2018 Jeep Grand Cherokee. I recommend the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 which splices into your factory wiring while protecting it from overload. I also recommend adding...
    view full answer...

  • Wiring Needed to Add a Brake Controller on a 2013 Hyundai Santa Fe
  • The Curt T-Connector # C56332 that you referenced actually doesn't carry the brake controller signal. It tees into your vehicle wiring and only carries the basic trailer lighting functions. If you are trying to tie in a Tekonsha brake controller, like the Prodigy P3 # 90195, then you also need the Universal Wiring Kit # ETBC7. This plugs into the Curt T-Connector and comes with all of the wiring and parts needed for a fully functioning 7-Way. I have attached an installation video of...
    view full answer...

  • Does Trailer Wiring Harness for 2019 Subaru Outback Need to be Stored in Hatch
  • Each of the trailer wiring harnesses that fit your 2019 Subaru Outback will be stored inside the rear hatch compartment. It can be completely out of the way though, as you can lift up the panel in the rear hatch where the connector is and simply store the connector there. Harnesses are specifically designed this way for many vehicles that aren't considered "full-time" towing vehicles as a way to help protect it from damage. If you want to have the harness stored outside your Subaru you'll...
    view full answer...

  • How to Determine if a 2017 Toyota Highlander has a Factory Tow Package
  • To determine if a 2017 Toyota HIghlander has a factory towing harness, start by opening up the rear hatch. Then, lift up on the rear compartment panel and pull it out. Remove the two driver-side panels by pulling up on them. There, you may see a factory 4-pole. If you do, then you know for sure you have the factory towing harness. If you do not, you may still have one that didn't come with the 4-pole connector so continue to the next steps. Pull up on the tabs connecting the floor covering...
    view full answer...

  • Difference Between Tekonsha Trailer Wiring Harnesses that Fit 2019 Honda Odyssey
  • The big difference between the two Tekonsha trailer wiring harnesses that fit your 2019 Honda Odyssey is how they draw power to activate the trailer lights. The # 118753 has a wire that runs up to the vehicle battery which is used to power all of the trailer lights directly from the battery. This is a much safer setup but the install in more involved and it costs more. The part # 118781 installs much easier but it draws power for the trailer taillights through the wiring panel of the Odyssey....
    view full answer...

  • Does The 2018 Chevy Express Van 3500 Have Factory Wiring For 7-Way Plug
  • The 2018 Chevy Express Van does have the brake controller wiring existing to wire in the brake controller if it has the towing package but that does not mean all of the wires are extended to the back of the vehicle. There may be a round plug with a cap inside your driver's side frame rail and if there is you can plug Hopkins 7-way plug # 30955 into the port for the 7-way. If there is not a round plug inside your driver's side frame rail then you may have a bundle of wires extended to...
    view full answer...

  • Trailer Wiring Harness Compatible With 2017 Lincoln MKC Without Factory Tow Package
  • If you don't have the factory tow package on your 2017 Lincoln MKC then you won't have the harness connector for the # HM11140694. Instead you will use the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118284 for your trailer wiring. This will connect to your factory wiring in the rear cargo area and will draw power directly from the vehicle battery to protect your vehicle electronics. I've attached an article to help with routing the power wire. If you don't already...
    view full answer...

  • Trailer Wiring Kit for 2020 Dodge Durango
  • To determine if you have the Factory tow package on your 2020 Dodge Durango I would look under the vehicle between the spare tire and rear bumper for the factory connector. If you see the round connector about 1-1/2" in diameter with a blank plug than you do have the wiring. If you don't have the vehicle or capability to look underneath it you can always contact a dealership with your VIN number and they can tell you every option that Durango came with. If you have the factory connection...
    view full answer...

  • Recommended 4-Way Trailer Wiring Harness for 2020 Toyota Tacoma
  • For your 2020 Toyota Tacoma I recommend the Tekonsha wiring harness, part # 118685. It has a higher maximum amperage compared to other options at basically the same price point. We generally recommend Tekonsha wiring because of their long lasting quality. To mount the 4-way use the brackets # 18144 and # C57202. Other parts you may still need to complete the towing setup on your Tacoma: Curt Trailer Hitch Receiver # C13264 B&W Tow and Stow Adjustable Ball Mount # BWTS10038B etrailer.com...
    view full answer...

  • Which Trailer Wiring Harness for 2018 Mitsubishi Outlander
  • As long as your Outlander isn't the plug in hybrid (PHEV), I'd recommend the # 118482 for vehicles without the factory tow package or # 118277 for vehicles with the tow package. If your vehicle has the tow package, it will have the tow package electrical connector located behind the driver's side bulkhead in the cargo area, to the rear of the wheel well as shown in the provided photo. You could also call your Mitsubishi dealer with the VIN, and they should be able to tell you how the vehicle...
    view full answer...

  • 2020 Honda Odyssey Difference Between Tekonsha 118781 and 118753 Wiring Harnesses
  • Both the # 118781 and the # 118753 are indeed confirmed to fit the 2018-2020 Honda Odyssey, both use T-connectors to plug into your tail light connectors, and both are rated at 5 amps for the stop/turn circuit and 7.5 amps for the tail light circuit. The main difference is that the # 118753 includes extra wire to run a power wire to the battery, whereas # 118781 comes with extra fuses which activate the "tow package" and power the harness through it. So, which one do you need? Well,...
    view full answer...

  • Installing 7-Way Trailer Connector on 2014 Ford E-350 Van
  • The connectors you have found are not confirmed to be for the trailer wiring and we don't have any wiring harness that is a fit for what you described. Because you don't have the factory trailer wiring, I recommend starting with the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118551 which will connect to your factory wiring behind each tail light. Then you will use kit # ETBC7 to give you the wire, connectors, adapter, and circuit breakers needed. Then you can...
    view full answer...

  • 2016 Toyota Highlander Limited Platinum Trailer Wiring Harness
  • We really dislike the term 'tow package' here at the etrailer.com World Headquarters, because the term basically has no meaning. In most folk's mind, saying something has the tow package would indicate the the vehicle rolled out of the factory and was completely equipped to tow which would be the case in a perfect world. But alas, that's not the case. In terms of which 4-pole trailer connector harness you need for your Highlander, there's a super-easy way to tell. Pull out the cargo...
    view full answer...

  • Does Tekonsha 7-Way for 2016 Ford F-150 Have 12 Volt Charge Circuit and Brake Controller Circuit
  • The T-One Vehicle Wiring Harness with 7-Way Trailer Connector # 118283 that you referenced does have the 12 volt accessory circuit active so you will be able to put a maintenance charge on your dump trailer battery while towing and does have the brake output circuit present but you will need a brake controller installed as well to activate the trailer brakes. Basically the 7-way has the wiring present but you need the brake controller to actually determine how much voltage to deliver to...
    view full answer...

  • Is Installation of T-Connector Wiring the Same as T-One Wiring for a 2019 Volkswagen Tiguan
  • The installation video and instructions for the Curt T-Connector # C56403 and Tekonsha T-One # 118811 are essentially identical. There might be slight differences but you could easily install one brand with instructions from the other brand no problem. You can definitely use the install video from the Curt (linked to this answer page) to install the Tekonsha on your 2019 Volkswagen Tiguan. If you don't already have a trailer hitch then I recommend using the Curt Trailer Hitch Receiver...
    view full answer...

  • Which 7 way Wiring Harness Do I Need for a 2018 Ford Transit T-350
  • I'm not sure what that plug is for exactly, but it's not anything related to the towing wiring, so that's not the wiring that you're looking for. If you don't have the factory tow package on your vehicle, you're not going to have a way to plug something like the Curt # C55774 (which is the correct harness for the T350 with the factory towing package)- this would utilize a US car connector plug to connect a 7 way. With that said, the Tekonsha # 22114 wiring harness is the correct harness...
    view full answer...

  • Parts Needed to Install 7-Way on 2021 Subaru Outback Wagon
  • Since your 2021 Subaru Outback Wagon does not have factory trailer wiring you'd need to first install a 4-way with part # 118467 and then convert it to a 7-way with a 7-way adapter like the part # 37185 to give you the 7-way. But since you are wanting to have the 12 volt circuit active your best solution is the adapter # ETBC7L instead of the 37185 as it comes with the wiring needed to complete that circuit. This will work great with the trailer hitch part # CU89FR as well.
    view full answer...

  • Trailer Wiring Harness for a 2019 GMC Acadia Without the Factory Tow Package
  • From the information I can find I believe your 2019 GMC Acadia will have the wiring routed back towards the rear of your vehicle whether you have the factory tow package or not (see attached photo). If you check up under the rear bumper of your Acadia you should find the wiring harness that you would plug the T-One # 118720 (for a 4-Way) or # 118276 (for a 7-Way) into. I have attached some installation videos on a 2017 Acadia as well as the written instructions for you to reference. I like...
    view full answer...

  • 7-Way and 4-Way Trailer Wiring Harness for 2017 Chevy 3500 Express Passenger Van
  • Yes, we do have a 7-way/4-way connector that fits the round connector on your 2017 Chevy Express Van. For that you'd want the part # HM40975. This has a 7-way on one side and a 4-way on the other. I attached an install video for this on a similar 2014 Express Van as well.
    view full answer...

  • No-Drill 5th Wheel Brackets That Fit 2021 Chevy Silverado 2500
  • We do have no-drill 5th wheel brackets which are a fit for your 2021 Chevy Silverado 2500. The correct fit for your truck is the following: - Curt Custom 5th Wheel Bracket Kit for Chevy/GMC Truck # C16429 This bracket kit will install onto your Chevy without any drilling, though they do require you use the Curt above-bed base rails (all 5th wheel brackets need to use the same manufacturer's base rails in order to fit). For that you can choose from two different finishes, either the...
    view full answer...

  • How to Determine Correct Trailer Wiring Harness for 2020 Acura RDX
  • In order to determine the correct trailer wiring harness for your 2020 Acura RDX - the option for +12-Volt Power Provision or without - you can check out the 8-pin connector on the driver's side interior trim panel, like in the accompanying photo. To see how to access this you can take a look below at the linked installation instructions. Once you see the 8-pin connector, check to see the number of red wires going INTO the connector. - Two Red Wires - With +12-Volt Power Provision:...
    view full answer...