The CE Smith Outrigger Poles # CE56510 comes with 2 poles, each have a removable aluminum sleeve pre-installed on the base. With the sleeve installed, the outer diameter of the base is 1-5/8", which allows the pole to fit into most aluminum outrigger pole holders. The sleeve can be removed to change the base diameter to 1-1/2" so that the pole can fit into most stainless steel outrigger pole holders. The base and sleeve are both pre-drilled with multiple holes so that they can accommodate... view full answer...
I may have a solution for you, but there's not anything specifically designed for such a task. For reference, most 100-lbs propane tanks weigh around 170-lbs when full. If you've got a 2" hitch receiver on the back of your 2019 Chevy Colorado then you can likely use the Viking Solutions Rack Jack II Hoist with Winch for 2" Hitches - 300 lbs # 310-VRJ001. This is typically used for hunting, but you could fashion some type of sling with some ratchet straps and attach that to the hook end... view full answer...
I contacted Viking but they do not offer replacement wheels or tires for the Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier for 2" Hitches # 310-VTG002. However, I was able to find that it uses an 8" diameter wheel and a 3/4" axle. The tire size is 3.50-8. Unfortunately, we do not have any replacement wheels or tires to fit this, but you can check your local hardware or farm supply store to track down the parts you need. view full answer...
Viking Solutions doesn't offer a wheel/tire as a replacement part, I'm sorry to say. However, I can provide you with the wheel/tire's specifications which would make it easier to find a replacement locally.
The wheel is 8 inches in diameter, and uses sealed bearings compatible with a 3/4 inch diameter axle. The tire size is 3.50-8 with an overall diameter of 15 inches. I'd recommend checking with a local Farm/Fleet type store or a discount hardware store like Northern Tool or Harbor... view full answer...
Yes, you could replace the included cable of the Viking Solutions Rack Jack Magnum Hoist with Winch for 2" Hitches - 650lbs # 310-VMH001. The cable dimensions are 32-1/2' long x 3/16" in diameter. view full answer...
The Viking Solutions Rack Jack Hoist with Winch for 2" Hitches - 300 lbs # 310-VRJ001 will work to remove and install the hitch based on the Curt Q16 hitch weight with sliding base. I recommend using the Demco 5th Wheel Lifting Bracket # DM6100 that will fit into the jaws of your hitch where the king pin would sit for a strong connection for the unit to work well for you.
This will likely not be able to place the hitch in the rails or pucks due to arm length, so some manual lifting... view full answer...
You are 100 percent right. I thought that maybe the wheel and axle assembly could be inverted so the wheels can stay on the Viking Solutions Tilt-N-Go II Cart - Hitch Mounted - 300 lbs Item # 310-VTG002 but they can't. Me and a coworker tried just now. While you can invert the assembly the tires would have to come off for it to fit. The tires are held on with cotter pins so it would be easy but would still require a few steps and additional time. view full answer...
Attaching/removing the wheels on the Viking Solutions Tilt-N-Go II Cart - Hitch Mounted - 300 lbs Item # 310-VTG002 is super easy. They are held to the axle with cotter pins. I have included a picture showing this for you. I have also linked the instructions which include instructions for this part and others from the same manufacturer. view full answer...
If your Kia Sorento has a 2 inch trailer hitch installed the Viking Solutions Tilt-N-Go II Cart # 310-VTG002 would fit and work well.
If you have the smaller hitch size of 1-1/4 inch this would not fit. view full answer...
The Viking Solutions # 310-VMH001 hitch hoist will easily connect to your truck with a 2-1/2" receiver when you use a Buyers Products # 337RTA252 2-1/2" to 2" Receiver Tube Adapter. I have included a link to this product and a video review. view full answer...
The Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier for 2" Hitches - Steel - 300 lbs # 310-VTG002 has a shipping weight of 57 lbs. The box is 48 inches x 23 inches x 8 inches. view full answer...
Technically, as long as your scooter weighs less than 300 pounds and can fit on the 36-1/2" long x 21-1/4" wide platform of the Viking Solutions SwivelLift # 310-VSL001, it can hold your scooter and raise it from the ground to your rear cargo area.
Although, there is an issue when it comes to your trunk. The only way that it is possible to use the # 310-VSL001 is by first opening your trunk, installing the lift, loading the scooter, and then uninstalling the lift to close the trunk.... view full answer...
We do indicate the cable diameter of Master Lock Cable Gun Lock # 99KADSPT as being 2mm, which I agree does sound rather small. So I went to our warehouse and measured this item with a digital caliper to get a confirmed cable diameter. The exterior diameter of the cable is 5mm. This includes the vinyl wrap on the cable.
I also measured the similar Master Lock Armored cable lock # 107KADSPT and found the cable as well as the metal clasp on the end of the cable to measure right at 5mm.... view full answer...
A cargo carrier like the Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier for 2" Hitches # 310-VTG002 can be used in most states even when the license plate is covered by the unit. Some states require relocation of the license plate if the plate is not visible so you will need to check with the local DMV as the laws do vary from state to state.
You can add a license plate bracket to the carrier like # CR79150 if needed. view full answer...
The Viking Solutions Tilt-N-Go II Cart # 310-VTG002 that you referenced weighs 43 lbs with wheels and 29 lbs without.
It is a tubular steel construction which means it will be very strong (300 lb capacity).
The tires are pneumatic and it has sealed wheel bearings. view full answer...
I do have an option for you but there is not a longer arm that can be added to the Viking Solutions Rack Jack II Hoist part # 310-VRJ001. There is also not a hoist that offers more lift than this so your only other option would be some sort of pulley system like the ProGrip Hunter's Hoist w/ Pulley part # 317-404780. view full answer...
Yes the Viking Solutions Rack Jack II Hoist with Winch for 2" Hitches # 310-VRJ001 that you referenced would work in the hitch of your 2010 Ford E-350 van. view full answer...
The Viking Solutions Tilt-N-Go II Cart - Hitch Mounted - 300 lbs # 310-VTG002 is a great product for anyone wanting a versatile cargo carrier, cart. This can absolutely be used with buckets that have a lid and use some tie-down straps like the Erickson Ratcheting Motorcycle Tie-Down Straps w Long Safety Hooks - 1"x6' - 400 lb - Qty 2 # EM05710.
This works very well with coolers, storage containers, and more. The versatility you mention is exactly why this product was designed. You... view full answer...
The Viking Solutions Rack Jack Magnum Hoist # 310-VMH001 can be completely broken down for storage and will not take up very much space. This will not be an issue with your Deck system and I did include a picture of the part as it will come to you. The winch can be left on the upright though, so you will not have to do a full rebuild every time you need to use it. view full answer...
Depending on which SuperGlide hitch that you have they range in weight from 200 lbs. to 265 lbs. But with the 300 lb. weight capacity of the Viking Solutions Rack Jack II Hoist with Winch for 2" Hitches # 310-VRJ001 the hoist will be able to handle any of the SuperGlide hitches just fine. The ground stand you asked about is no longer available. That being said you would still be able to use the hoist by putting it into the 2" hitch on your 2020 Chevy 2500. view full answer...
I attached a picture that has several dimensions of the Viking Solutions Rack Jack Magnum Hoist # 310-VMH001.
I also spoke with my contact at Viking Solutions and he told me they designed this hoist for fitting a hitch height of around 18 inches. The outriggers will reach the ground at this height, but we recommend that a small gap of 1”-2” be allowed for suspension compression after the load is lifted. This helps disengage the pressure on the lynch pins holding the outrigger tubes... view full answer...
To answer your first question in regards to the Viking Solutions Rack Jack Magnum Hoist with Winch, # 310-VMH001, and "...pulling the supported load ... rather than vertically...". While an 85 lb. load may be successful, it has not been tested for that and is not the intended use. This is designed to support a vertical weight and pulling of the load over the vehicle does not allow the legs to provide support as intended. I do believe you can fabricate a mount to replace the winch with... view full answer...
In order to get situated properly in this Classic Accessories Float Tube, part # CA32014, you will need to start on a gentle slope (like a boat ramp). Unfasten the hook and loop holding the apron to the pocket inside of your float tube and unclip the spreader bar on the same side.
Attach fins to your feet, then place your float tube in knee-high water. Step into your tube from the open side and turn so that your back is facing the backrest.
Now reinsert the spreader bar into its... view full answer...
Part of the shank on the Viking Solutions Tilt-N-Go II Cart - Hitch Mounted - 300 lbs Item # 310-VTG002 is square and fits into a square bracket mounted on the carrier so it cannot tilt when installed in the trailer hitch. The other side of the shank, which is round, is held to the bracket with a pin so it is prevented from tilting on that side too. I have included a link to the installation instructions which contain further details. view full answer...
For loading 75 lb. ebikes, the Viking Solutions Rack Jack II Hoist with Winch for 2" Hitches, # 310-VRJ001 would be sufficient. I don't see the need for the larger hoist, # 310-VMH001.
We have available the Westin Truck-Pal Fold-Up Bed Ladder, # 10-3000 that stores on and folds down from the tailgate, making it easy to get in and out of your truck bed. And the Powerbuilt Adjustable Tire Step, # ALL647596. view full answer...
The Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier part # 310-VTG002 comes with a few different sets of pins. These are all called out for you in the manual I have attached but the pins that are used to unlock/tilt the frame assembly will be 8mm x 50mm and the pins that are used to hold the wheels in place are 25mm. view full answer...
It is possible to replace the winch on your Viking Solutions Rack Jack II Hoist part # 310-VRJ001 with an ATV winch like part # CU122390. ATV winches are rated for horizontal pull not to lift or hoist however, I did contact ComeUp (one of our winch manufactures) and they said since all you are using it for is to lift a kayak you would be okay to mount it to the Rack Jack. Please keep in mind the ATV style winches are not made to lift so I would not lift anything heavier than your kayak... view full answer...
The Viking Solutions Rack Jack Magnum Hoist w/ Winch # 310-VMH001 would work great to help get a fifth wheel hitch in and out of the truck bed. It has more than enough capacity and would take all of the strain out of having to lift the hitch into the bed. B and W has the B&W 5th Wheel Lifting Device for Companion and Patriot Hitches # BWRVXA3130 which was designed to be used with hoists like this and the Companion hitch like you have to make it even easier. Basically this fits into the... view full answer...
The wheels that come with the Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier for 2" Hitches part # 310-VTG002 are 8" diameter x 3" wide. view full answer...
The square tube portion of the hitch adapter included with the # 310-VTG002 Viking Solutions Tilt N Go hauler will be sized just below 2 inches. The one we measured was slightly larger than 1-7/8 inches. The shank portion is typically going to be sized just under 2 inches while the hitch receiver will be sized just slightly larger than 2 inches to allow room for manufacturing tolerances.
If you click the provided link, you can see a product demonstration video featuring the hauler. view full answer...
I've provided a photo with the outside dimensions of the Viking Solutions Tilt-n-Go Hauler # 310-VTG002 for you. From the tip of the handle to the far opposite edge lengthwise, the cart/trailer is 63-1/2 inches in length. At its widest point at the wheels, the cart/trailer is 22-1/4 inches wide. view full answer...
I went out to the warehouse and weighed each component of the Viking Solutions Rack Jack Magnum Hoist part # 310-VMH001 for you. The entire weight can vary from unit to unit slightly but it should be around 70 lbs. The individual weights are all listed below:
Winch: 8 lbs
Upper Boom: 17 lbs
Telescoping Adjustable Outrigger: 3 lbs
Lower Mast Tube: 18 lbs
Outrigger Tube: 7 lbs
Receiver Tube: 13 lbs view full answer...
For ground clearance reasons you'd want to always remove the wheels of the Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier for 2" Hitches # 310-VTG002 when it's being used as a hitch mounted cargo carrier. view full answer...
According to sketches we've received from Viking Solutions in the past it looks like the outside section of the Rack Jack Magnum Hoist w/ Winch # 310-VMH001 sits about 17.1" out from the center of the hitch receiver.
Attached is the dimensional image as well as a review video for you to check out. view full answer...
If you do not recall the combination of your Trigger Lock, you will need to have a locksmith drill out the lock. The only other option is less appealing and much more time consuming - manually going through each of the possible combinations until you find it.
To avoid this problem in the future, you may want to consider going with a keyed option, the Master Lock Gun Trigger Lock # 90KADSPT, which comes with two keys in case you misplace one. This is a single lock but there is the option... view full answer...
The platform dimensions of the Viking Solutions L-E-Vator Portable Loading System # 310-VLV001 are 16-1/4" long x 15" wide so it would work with the generator you have since it is larger than that at 18 x 24 inch. view full answer...
The Viking Solutions Rack Jack Magnum Hoist - Hitch Mounted - 650 lbs # 310-VMH001, the lower mast tube is 2-1/4 x 2-1/4 inches. The receiver tube is 2 x 2 inches. The round support leg tubes are 1-3/4 inches in diameter. I've attached a video of how this hoist operates. view full answer...
The Viking Solutions Rack Jack Magnum Hoist with Winch, # 310-VMH001 has an overall height (at shortest setting) of almost 82". You will want to measure the height of your tailgate to ensure fitment. Please note the linked product review video as well. While this will fit with any 2" hitch receiver, I am cautious to recommend its use with a Honda Pilot, but please verify the measurements against your specific vehicle. view full answer...
If the Master Lock Gun Trigger Lock # 94DSPT is locked and you have forgotten the combination you will have to reset the combination.
To change the combination you will need to set dials to combination (combination is preset to 0-0-0 by factory). With dials set to combination, move release lever to open, or up, position. Pull apart the two sides of the gun lock.
Next, you will need to use a pen to press and hold the reset button that is on the left side of the lock and select a... view full answer...
The AO Coolers Fishing Cooler Backpack # AM39NR which features the dry bag you asked about is integrated into the cooler backpack and is not removable. The dry bag is part of the insulated cooler of the backpack and works to keep the ice and cold items together in the backpack cooler. view full answer...
Yes, the insulated cooler section on the AO Coolers Fishing Cooler Backpack # AM39NR is ok to put fish in. The cooler section of the AO Coolers Fishing Cooler Backpack # AM39NR features a dry bag that will allow you to keep ice, bait, drinks, fish, or your lunch.
So, you can hike in with your lunch on ice and hike out with the catch of the day! view full answer...
The AO Coolers Fish Cooler Bag # AM57NR weighs 18-lbs.
This cooler bag also measures 7" long, 48" wide, 26" tall and is reinforced with 1" thick foam.
view full answer...
The Viking Solutions SwiveLift Loading System for 2" Hitches part # 310-VSL001 weighs about 50 lbs put together. It comes in 3 pieces and is put together piece by piece for a quick and easy setup. I have attached a video of it being put together so you can gauge rather you can do it yourself. view full answer...
The Classic Accessories Float Tube part # CA32001 does actually come with two rod holders for your fishing poles so you have a place to hold them while not in use. view full answer...
Yes, the Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier # 310-VTG002 does come with the adapter shank for mounting it to a 2" trailer hitch receiver. I have highlighted the specific part in the attached picture and you can see it installed in the linked review video. view full answer...
If you do not remember the combination then there are 2 options. First, you could go through the 1,000 possible combinations manually until you find the one that works. Or you can attempt to drill out the lock. The only way to reset the combination is if you know the current combination.
Going through the possible combinations isn't all that hard, just time-consuming. Start with 000 then go to 001, 002, and so on. It may sound ridiculous but I have had to do this in order to save the... view full answer...
The height of the handle on the Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier for 2" Hitches # 310-VTG002 is 13-1/4". I attached a photo to illustrate this and I also included a demonstration video for you to check out. view full answer...
The Trimax Gun Trigger Lock # TMX25ZR comes with 2 keys that are keyed alike but each lock has it's own key so there isn't a way to order them keyed alike.
As annoying as that CAN be, it may help to think of it as an extra precaution to help protect misuse of your firearms. view full answer...
These lifts are not in stock at this moment otherwise I would go measure this for you. Our best estimate is that the portion of the vertical tube below the 2" horizontal tube measures between 4 to 7 inches. If you are asking about the platform - it does not have to be lower all the way down. I have attached a picture illustrating this.
You will also need a hitch pin and clip to attach this to your receiver. You can use the etrailer # C21504 zinc coated pin. view full answer...
Yes, the ratchet lever of the Viking Solutions L-E-Vator Portable Loading System # 310-VLV001 works as a brake so that when you let go of the handle it does not spin out of control and lower. It will stop wherever you release the handle. If you check out the end of the review video I attached you can see it stays in the same place when our demo person releases the handle. view full answer...
The rope of the ProGrip Hunter's Hoist with Pulley and Rope Lock # 317-404780 is 20 feet long but since this is a pulley system that would mean the overall height it can lift is less than that since the rope has to travel from the ground to the pulley block and then to the person holding the rope. So realistically it would have ability to lift around 12 to 15 feet depending on how tall the person is on the other end and how high they were willing to reach up. The weight capacity is 300... view full answer...
According to my contact at Rightline Gear, they do not offer a bed tent compatible with the unique bed configuration of the Ridgeline.
The closest fit they have would be the tent for the Cadillac EXT or Chevy Avalanche, but the tent would be WAY too large for your truck.
Rightline does offer a small, 2 adult pop-up tent, part # RL110995 that you might be interested in. view full answer...
The Viking Solutions L-E-Vator Portable Lifting Tool # 310-VLV001 that you referenced has a 300 lb weight capacity so it would easily handle a 140 lb generator like what you have. view full answer...
The Viking Solutions Rack Jack II Hoist w/ Winch - 2" Hitch Mount # 310-VRJ001 you are looking at has a weight capacity of 300 lbs and will help out greatly since a full 100 lb propane tank only weighs in at about 170 lbs.
The nice thing about this hitch mounted lift system is it's portable so you can use it in a variety of circumstances and you aren't limited to a fixed system.
If this doesn't quite fit your needs please let me know how exactly you're wanting to use the winch (in... view full answer...
The overall width of the Viking Solutions Tilt N GO part # 310-VTG002 is 47-1/2 inches without the handle. With the handle the width is 63-1/2 inches. If you wanted the width from the center of the hitch pin out to the side with the handle the measurement is 39-3/4 inch. view full answer...
The 205/75R15 tires measure slightly over 27". Tire covers for your 2008 Jayco Jay Flight Travel Trailer with tandem axles, I suggest the Adco Tyre Gard RV Wheel Cover - Double Axle, # 290-3923 for white, or # 290-3723 for diamond plate.
Please note the linked product review videos below. Happy Camping! view full answer...
We have two options for you that fit the 2022 Ram 2500, the DeeZee Oval Tube Steps, # DZ16422-16336 in diamond plate pattern with bright aluminum finish or, the DeeZee Oval Tube Steps, # DZ16121-16336 that are black powder coated steel. Each are 26" long x 5" wide.
Please note the linked product review video below. view full answer...
The framed platform on the Viking Solutions L-E-Vator Portable Loading System # 310-VLV001 will travel 37" to the base of the stand. view full answer...
The easy way to fill the part # CA32007 will be to use the pump part # 052963611113. This will make inflation much easier. Otherwise you'll have to blow into it manually. view full answer...
The Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier for 2" Hitches, # 310-VTG002 is an import item supplied as a kit. Any modification such as replacing the axle with an extended version of, will need to be made by the purchaser as a custom fabrication. view full answer...
The Viking Solutions L-E-Vator Portable Loading System - 300 lbs # 310-VLV001 is designed to be folded up and moved from site to site in the back of a truck or similar vehicle. It is also designed to fit most tree stand carriers for additional portability. It weighs just 20 lbs and comes with a 1 year warranty. It is made of powder coated steel and is reinforced with galvanized steel cable to lift up to 300 lbs.
I've attached a couple pictures and a video to assist. The collapsed... view full answer...
The chrome pulley on the ProGrip Hunter's Hoist with Pulley and Rope Lock - 20' Long x 3/8" Diameter part # 317-404780 is fixed and does not move so the 14-1/2" between the pulley and the top hook cannot be shortened. There will be that 14-1/2" of distance that you cannot lift the tire with the hoist.
You may consider a Dutton-Lainson StrongArm Electric Winch w/ Remote and Pulley Block, AC Powered - 1,200 lb # DL25727 which allow you lift the tires all the way up to the garage's cross... view full answer...
I have a solution for you, but the Viking Solutions Rack Jack # 310-VMH001 hoist is secured via bolt on to the lower tube and there are no additional mounting holes on that lower tube it without voiding any warranty or compromising the integrity of the construction. If the height/length of the jack is the main concern, I recommend going with the Viking Solutions SwiveLift Loading System for 2" Hitches # 310-VSL001 . This lift is 55" tall compared to the 81"+ of the Rack Jack and has an... view full answer...
The Viking Solutions Rack Jack Magnum Hoist with Winch # 310-VMH001 that you referenced weighs 68 lbs.
I attached a review video for this jack for you to check out as well. view full answer...
The Viking Solutions Rack Jack Magnum Hoist with Winch # 310-VMH001 is a great option for hoisting a 5th wheel hitch up into the bed of your truck. Just toss in the Demco 5th Wheel Lifting Bracket # DM6100 and you're good to go! view full answer...
Yes! You can both raise and lower the Viking Solutions SwiveLift Loading System for 2" Hitches # 310-VSL001. It is important to note, though, that while lowering the load, the SwiveLift will not stop to suspend the load while lowering like it does in the raising function. You just need to continuously hang onto the handle while lowering.
The video I attached talks about the lowering function at timestamp 2:20. view full answer...
To install the winch on your Viking Solutions SwiveLift Loading System # 310-VSL001 I recommend finding a long enough 8mm wrench and placing some tape over one side to hold the nut in place and lay the washer on top of the wrench to get it lined up with hole and put the bolt in. view full answer...
You can definitely use the Classic Accessories Cumberland Float Tube # CA32001 in saltwater applications. That being said, you'll want to make sure that after taking it out on saltwater, you take the time to hose it down with fresh water to get rid of any saltwater residue. This will ensure it will hold up well over time. view full answer...
The B&W Companion hitches for your 2021 Ford F-250 do not position differently, and it is likely you will be okay to use the fixed hitch with the Turnoverball mount, which are the following parts:
- B&W Companion 5th Wheel Trailer Hitch # BWRVK3500-5W
- Custom Underbed Installation Kit # BWGNRK1116-5W
The only way to know for sure though is to use the following formula, which will tell you if you can make a full 90 degree turn safely:
(A + B) - C = Clearance
A = Distance from... view full answer...
While Vikings Solutions doesn't make the SwiveLift Loading System # 310-VSL001 with a shorter stinger, you may be able to utilize the Rack Jack II Hoist # 310-VRJ001 instead for your 2014 Buick Enclave since you can push your cargo in towards your rear hatch area while letting some of the cable out. Aside from that there isn't anything else that would accomplish what you're trying to do short of using loading ramps and finding a way to mount a winch inside your SUV. view full answer...
When the 19x47 Curt Cargo Carrier for 1-1/4" and 2" Hitches - Steel - 300 lbs, part # C18110, is installed on your 2004 Honda CR-V you will be able to open the rear door on your 2004 Honda CR-V when the carrier is empty. Unfortunately, the Viking Solutions Tilt-N-Go II Hunting Cart and Cargo Carrier - 2" Hitch Mount - Steel - 300 lbs, part # 310-VTG002, will not work for you. Your 2004 Honda CR-V has a rear door which opens to the right. This is towards the handle of the Viking Solutions... view full answer...
There is not a hitch mounting application for a tent if that is what you are referring to. We have some tents that attach to the back of SUV's and truck beds, but nothing for a 2015 Chrysler 200. My recommendation is to either use a separate tent like the Rightline Pop-Up Tent - Sleeps 2 - 90" x 72" x 42" # RL110995 or the Let's Go Aero ArcHaus Tent Shelter - 10' Long x 6' Wide x 6-1/2' Tall # SAR024.
The rooftop option like the Yakima SkyRise is not an option for your vehicle because... view full answer...
I do have an option for you but the Viking Solutions Rack Jack Magnum Hoist part # 310-VMH001 won't work for lifting items on a roof, the boom is not long enough to reach this high. I would instead recommend some sort of pulley system like Thule MultiLift Cargo Lift and Storage System part # TH572. view full answer...
To reset the combination on the Master Lock trigger lock 94DSPT follow these 5 steps:
First, open the lock by pulling apart the two sides of the lock and completely removing from the gun.
Then, push the lever into the down position.
Next, with dials set to the current combination, use a pen point or similar narrow object, press the reset button on the left side of the lock in toward the center of the lock.
After that, continue to apply pressure to the reset button, and set the... view full answer...
The Viking Solutions Tilt-N-Go II Hauler, ATV Trailer, and Cargo Carrier # 310-VTG401 can absolutely use the Brophy Stabilizer Clamp and U-Bolt for 2" Hitch Receiver # RSCP to help stabilize the carrier.
You can alternatively use an internal stabilizer like # 63232 or for the best stabilization use the Blue Ox Hitch Receiver Immobilizer II # BX88224 for stabilization both vertically and horizontally. view full answer...
The Viking Solutions Rack Jack Magnum Hoist with Winch for 2" Hitches - 650lbs Item # 310-VMH001 does come apart easily for quick storage. You can pull the swiveling tube and legs off of the base tube and place each part separately in your storage space without having to take any bolts out. view full answer...
The Classic Accessories Teton part # CA32013 has two air bladders. A rear one and a main one. One of the inflation valves is like a standard inflation valve when inflating water accessories like a beach ball and the other is a longer valve that you unscrew the cap of to open and close. view full answer...
The Viking Solutions L-E-Vator Portable Loading System # 310-VLV001, measured from the ground up to the top of the winch handle (when the handle is at the highest point in its rotation), will extend up 56-inches from the surface the unit is resting on, according to my contact there. view full answer...
I do have an option for you. The Classic Accessories Float Tube part # CA32014 is not motorized. It will allow you to float while fishing and most people use flippers part # CA63227.
The Classic Accessories 9' Pontoon Boat with Padded Seat - The Colorado - Green part # CA69660 does have a motor mount but you would need to add your own trolling motor because it does not come with it. view full answer...
Master Lock cable gun lock # 99KADSPT has a vinyl coated cable and the lock cover has a plastic housing over the steel components so it does have some weather resistant features. But those features where designed more to protect the gun from getting scratches from the lock and not with weather resistance in mind. You will still want to try to keep it as dry as you can. view full answer...
We certainly can!
On the product page which you can access by clicking the provided link, click the down arrow and choose the 'keyed alike' option, then the quantity of locks you needed. There's a nominal upcharge for each lock. view full answer...
We do not currently offer any tent that will fit the short bed of your 2006 Honda Ridgeline due to how uniquely short the bed is.
We do offer a free-standing tent from Rightline, their Pop-Up Tent # RL110995, which is spring-loaded to open up instantly when removed from the included storage bag. This item is great for one-person set-up or for young campers. It is intended for use on the ground but not in a vehicle. It measures 90 x 72 x 42, sleeps two adults and weighs under 5-lbs. view full answer...
If you have a factory tow package, then you'll need to refer to your Owner's Manual for the exact specifications of your hitch in terms of its tongue weight. The hitch receiver is a 2 inch by 2 inch receiver though, so you'll likely have a Class II or Class III like you said.
If you don't have a factory tow package, I recommend picking up the Curt Class III, part # 13442. This will give you a higher than average tow capability and let you use a wider range of carriers.
Tongue weight... view full answer...
The cable that is included with the Viking Solutions Rack Jack Magnum Hoist with Winch for 2" Hitches part # 310-VMH001 is 32-1/2 foot long, not 32-1/2 inches long. Therefore, it will reach the ground for flat and heavy objects. I have attached a dimensional photo for you as well if needed. view full answer...
The Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier # 310-VTG002 is compatible with most any vehicle that has a 2" receiver, including your Jeep Wrangler. You will need to verify that your 2" receiver will work with the carrier.
This carrier has a measurement of 4-1/2" from the center of the hitch pin hole to the front edge of the basket on the carrier. Depending on your receiver and bumper combination this may or may not fit. Also depending on your spare tire and what you intend... view full answer...
The overall height of the Viking Solutions L-E-Vator Portable Loading System, # 310-VLV001, is 48" but the max distance to lift items is 40". Please compare this to the height of your vehicle's tailgate for comparison. view full answer...
The Master Lock Armored Cable Gun Lock, # 107KADSPT, is designed as a gun lock and is not intended for all-weather conditions. Water and salt could cause corrosion of the steel components. Instead, I recommend separate locks and cable that are coated and/or made of corrosion resistant materials.
Take a look at Master Lock Covered Solid Body Padlocks, # 141T. These locks are constructed of corrosion resistant materials so would work well outdoors. I would use these locks with Master... view full answer...
The Classic Accessories 9' Pontoon Boat # CA69660, that you referenced, comes with a 2-year warranty and there is a repair kit available!
For the repair kit you will want part # CA32005 which fits easily into the pocket on your pontoon boat. It comes with the following:
Spring clevis pins to secure frame - 4 large
Replacement inflation valve
Inflation adapter - use with a variety of pumps
Valve wrench
Bladder patch kit
Corrosion-resistant oarlock with cotter pin for secure fastening
Wing... view full answer...
Yes! The Classic Accessories 9' Pontoon Boat # CA69660 was specifically designed for fishing enthusiast like yourself and has an adjustable motor mount that can be set in 2 different positions. Please note that this does not come with a motor.
The pontoon boat also comes with a fishing rod holder that can be mounted in 6 different positions, and a rear wire platform that is perfect for holding any equipment that you may need. view full answer...
The Classic Accessories 9' Pontoon Boat # CA69660 that you referenced has a shipping weight of 75 lbs, it weighs in at 71-1/2 lbs, and it has a weight capacity of 400 lbs.
The weight capacity includes any equipment you will be carrying with you so you may want to do some checking on the weight of your equipment if you think it may be close. view full answer...
The seat on the Classic Accessories Pontoon Boat # CA69660 can be adjusted forward and backward but it does not fully swivel.
This is a really nice, high-capacity pontoon boat that features 20 pockets, 2 insulated drink holders, 3 positions to mount brass oarlocks and 2 included aluminum oars that break into 2 pieces for easy storage. If you also need an air pump, you can use # 052963611113. view full answer...
Yes, the Classic Accessories Pontoon Boat, part # CA69660, does include 2 aluminum oars. The oars even break down into two pieces for easy storage. view full answer...
The Classic Accessories 9' Pontoon Boat # CA69660 can easily handle an avid fisherman up to a 400-pounder so you have no worries about using this craft for your fishing outings. Your comfort is assured thanks to adjustable oar locks, foot rests and seat. A handy cargo basket is included too so you have a place for the beer cooler, tackle box and snacks. 2-piece aluminum oars come with it too.
The boat comes in three main parts, the two pontoons and the tubular steel frame, so handling... view full answer...
Yes, the Classic Accessories 9' Pontoon Boat # CA69660 includes a 2-position trolling motor mount along with oars and a cargo basket to hold your trolling motor battery, tackle box and beer cooler. It also features an adjustable seat, oar locks and foot rests so you can be comfy while catching your dinner.
The boat consists of three main parts (the two pontoons and the central tubular steel seat frame) so you will be able to easily handle each part separately. In total the boat weighs... view full answer...
The Classic Accessories 9' Pontoon Boat with Padded Seat - The Colorado # CA69660 has a Class I river rating. It also features a large amount of storage capacity, with 20 pockets and a pair of insulated drink holders so you can snack all day long! view full answer...