It definitely is a guessing game when it comes to filling your holding tanks. For a much more accurate reading of the water level in your black tank, as well as your fresh and gray, you can install the SeeLeveL RV Holding Tank Monitor # SE44VR. These strips simply stick onto the outside of of your holding tanks and have sensors every inch instead of just the old 1/3, 2/3, 3/3 type sensors that manufacturers install in their RV's. Because there's more sensors on these strips the reading... view full answer...
Thank you for the photos! Based on that it looks like you have a spigot to hub black water tank valve, like you mentioned, where the hub end fits over one pipe and the spigot end fits into the other pipe. So for a spigot to hub replacement valve with a 72 inch cable you will need the following:
- LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank - Spigot to Hub - 72" Cable # 34466N4AB72GMA
Then to complete the install you will just need the LaSalle Bristol ABS Solvent... view full answer...
To widen your 1-1/2" pipe to 3" using the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1 you would first need the Valterra DWV Adapter for RV Sewer System - ABS Plastic - 1-1/2" Hub to FPT # D50-2922 to screw onto your current fitting. The # T1041-1 would then slide over the 1-1/2" hub fitting of the # D50-2922 allowing you to connect a 3" pipe to your sewer system.
Between these two fittings you'll want to use some ABS Solvent Cement # A05-0303... view full answer...
You'll first want to attach the LaSalle Bristol Clean Out Adapter for RV Sewer System # 344633703 to your current setup and then you can attach either the Valterra RV Sewer Termination Adapter # T1029-2 or the Valterra Rotating Adapter for Rigid RV Sewer Pipe # T1028 to the unthreaded side of the # 344633703 with some Valterra ABS Solvent Cement # A05-0303 view full answer...
The Valterra RV Sewer Spigot with Flange part # T1006 has a spigot fitting which means it will slide into a 3" diameter sewer pipe and the Valterra RV Sewer Slip Hub with Flange part # T1005 has a hub fitting which means it will slide onto a 3" diameter sewer pipe. view full answer...
The LaSalle Bristol Long Sweep Elbow Fitting for RV Sewer System # 344632276 is 3.5" from the center of the hub to the center line of the other hub. Since yours broke off you'll have to cut of the chunk of the hub left on the pipe before you can install anything else. I recommend using part # 344633001 and some straight pipe to get back out to where you want the valve to sit.
As for the valves, I recommend the Bristol Double RV Waste Valves # 34466ND15AAR. You'll need to cut off the... view full answer...
It sounds like you're going to need the Valterra Eccentric Tank Reducer # T1041-1 which will mount directly to your 3" spigot, while the 1-1/2" hub slides over the sewer pipe.
Now you can connect to the Valterra Waste Valve for RV Gray Water Tank w/ Cap # T1001C, like you mention.
From here, you can attach the Valterra Gray Water Drain Connector # T01-0094VP for the 3/4" hose connection, or you can use # T01-0091VP if you want a 90° angle 3/4" hose connection.
We have various... view full answer...
The LaSalle Bristol RV Sewer Termination Adapter part # 34466V293B3 has a 3" hub fittings so it is designed to slide over a 3" outer diameter black sewer pipe and can then be fused on using the LaSalle Bristol ABS Solvent Cement part # 3447530889. If you're replacing a fitting then you will lose some length as you must cut the old fitting off in it's entirety.
If this was not the info you were looking for please just let me know and I'll do by best to assist. view full answer...
Yes, of course you can insert and glue the Valterra Rotating Adapter for Rigid RV Sewer Pipe, # T1027 if you choose to. If your objective is to have a permanent/semi-permanent arrangement of your RV to a sewer system, I suggest the Valterra Rotating Adapter for Rigid RV Sewer Pipe, # T1028. This adapter converts an RV waste valve to connect to 3" hub sewer pipe. The bayonet fitting rotates, making it easy to connect to the lug fitting on your RV's waste valve and the 3" hub slides over... view full answer...
So the difference is purely in how the two connect to your sewer pipe, which will also tell you which one you need; one will slide into the pipe (the spigot) while the other will slide onto the pipe (the hub):
- Slide Into Pipe: Valterra Waste Valve for RV Black Water Tank - 3" Spigot to 3" Lug # T50A
- Slide Onto Pipe: Valterra Bladex Waste Valve for RV Black Water Tank - 3" Hub to 3" Lug # T50
To secure the valves to your pipe you would just need the Valterra ABS Solvent Cement... view full answer...
The part you're needing for your Bristol Double RV Waste Valves # 34466ND15AAR is a hub so you'll want the LaSalle Bristol RV Sewer Slip Hub with Flange # 34466V1515.
The difference between the # 34466V1515 (hub) and # 34466V1515S (spigot) is how they connect to the pipe from your gray tank. A hub will accept the pipe into it whereas a spigot will slide into a hub. view full answer...
The inner diameter of the female side of the LaSalle Bristol RV Sewer Termination Adapter # 34466V293B3 that you referenced is 3 inches. view full answer...
From what I can gather it sounds to me like you need the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1. The 3" Spigot mounts directly in the gray water tank outlet while the 1-1/2" Hub slides over sewer pipe.
Then for a 1-1/2" diameter gray-water sewer pipe we have the LaSalle Bristol Cable-Actuated RV Waste Valve for Gray Water Tank. This is valve is available in with cables that are numerous lengths, which I'll list for you so you can choose the... view full answer...
All of our hoses and fittings are for the standard fit bayonet which is not what you have. You can either use the adapter # T05-2285VP you referenced to adapt the older thetford fittings to the standard bayonet or if you don't want an additional adapter I recommend replacing current fitting with the Valterra RV Sewer Termination Adapter - 3" Lug Fitting to 3" Hub # T1029-2. view full answer...
Ok so it sounds like what you are wanting to do is just replace your black water tank's waste valve, and I can let you know how to determine the correct one, as there unfortunately isn't a way for us to know the exact valve for your R-Pod.
It's pretty simple though, because you just need to know if the valve you are replacing slid over your pipe or into your pipe.
If both ends of your waste valve slid into your sewer pipe you will need the Valterra Bladex Waste Valve for RV Black... view full answer...
Yes, using the Valterra RV Sewer Slip Hub with Flange # T1005 paired with a guillotine style waste valve like the Valterra Bladex Waste Valve Body # T1003VPM is a good option for your gray water tank. This would bond together using the Valterra ABS Solvent Cement # A05-0303. view full answer...
I believe we have what you're looking for.
We have the P-Trap Fitting # LSB86XR, which will install under your sink, shower or tub and will fit onto 1-1/4" to 1-1/2" diameter pipes. view full answer...
The two flanges are essentially the same thing but made by two different companies so either the # 34466V13B or the # T1009 would work great. view full answer...
The part # D50-2880 has an outer diameter of 1-1/2 inch so the correct flange you'd need to fit it is the part # T1005-1. You'll need ABS solvent part # A05-0303 too and you'd be set. view full answer...
You will need the Valterra Rotating Adapter for Rigid RV Sewer Pipe - 3" Hub to 3" Bayonet - Black Plastic item # T1028 and a 4" to 3" adapter that you can find at your local hardware store to permanently connect your camper to you septic station. view full answer...
To install the Projected Male Slip Fitting # 372216-A-MS-A to your gray tank you're going to clean the surface area and then apply some cement like the Valterra ABS Solvent Cement # A05-0303 to the shorter side of the fitting. Give it 30 minutes to cure and then you can attach your hose and clamp to the longer end that is sticking out! view full answer...
The Valterra Double Elbow DWV Fitting, # D50-3047, measures 9 inches from end to end. Also, from the horizontal opening to the vertical opening the measurement is 7 inches. view full answer...
What you can do is hook the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub Item # T1041-1 onto your 1-1/2" pipe using some Valterra ABS Solvent Cement - 1/4 Pint Item # A05-0303 and a hose clamp.
Next you'll hook in the Valterra RV Sewer Termination Adapter - 3" Lug Fitting to 3" Spigot Item # T1029-1 using some # A05-0303 and a hose clamp.
If your hose has the bayonet end or if you have no end on the hose you can just hook it in as well using a hose clamp. view full answer...
Looking at the picture you provided it's either the Valterra Street DWV Fitting for RV Sewer System - 90 Degree - 1-1/2" Spigot to 1-1/2" Hub Item # D50-2880 or Valterra Street DWV Fitting for RV Sewer System - 90 Degree - 3" Spigot to 3" Hub Item # D50-2882. You'll just need to measure the pipe to see if it's 1-1/2" or 3" in diameter. view full answer...
You're right, a picture of the flange-to-flange width is definitely a good idea, so I contacted the manufacturer, Valterra, to get the dimension, and then went ahead and made a photo for you of the Valterra elbow you asked about:
- RV Sewer Elbow - 2-Way - 3" Hub x 3" Rotating Flange x 3" Rotating Flange # T1039-1
As you can see by the accompanying photo, the distance between the two flanges is 6 inches. I have also added a link below to a video review of the # T1039-1 if you'd like... view full answer...
The Valterra Coupling for Rigid RV Sewer Pipe # F02-2104 is designed for attaching 3 inch ABS style pipes. The larger end is for attaching to a schedule 40 style ABS pipe and the smaller end for attaching to a thin walled style pipe. When making this attachment you do need to use ABS solvent cement like the part # 3447530889. view full answer...
The LaSalle Bristol Coupling for RV Sewer System # 344633003 is designed to fit over a 3 inch pipe so it has a 3 inch inner diameter and the outer diameter is 3.5 inch. view full answer...
The closest match that we have is the Valterra # T1035-2 RV Sewer Elbow. The internal measurement on the spigot end is 3" and is meant for a glued connection rather than a push together connection with an o-ring. view full answer...
The bayonet part of the Flo-Jet macerator is going to connect to your 3" black tank waste valve as the input and use a 3/4" garden hose connection as the output so you wouldn't need the EZ Coupler 4-in-1 Threaded RV Sewer Adapter # F02-3112CL or the Valterra Gray Water Drain Adapter # T1020-5VP.
You would just need your black tank waste valve to have a bayonet fitting for the macerator to attach to like the # T50A has. If you are unsure if your waste valve has a bayonet fitting you... view full answer...
I do see what you are saying, and though we do have a solution, your hoses do not have the appropriate connections for the RhinoFLEX RV Sewer Hose T-Adapter for 90-Degree Elbow Fittings # CAM39734.
What I strongly recommend instead that will fix your problem is the Flush King Reverse Flush Valve for RV Holding Tanks and Sewer Hoses - 3" Diameter # F02-4350 because it is designed for the exact problem you are having. It will flush the hoses so the waste water does not stay the "T" on... view full answer...
I think I'm following you. It sounds like your portable tote tank has a threaded fitting, but your sewer hose has a bayonet fitting like a typical sewer hose. If that is the case, then I have a solution for you, but we don't have a single adapter.
Instead, you will want to use fitting # T1029-2 and fitting # 344633703 to make the adapter you need. The non-threaded end of part # 344633703, will fit into the end opposite of the 3 bayonet lugs on part # T1029-2. You will want to use ABS... view full answer...
The Valterra Eccentric Tank Reducer, part # T1041-1, is installed with cement. When you reinstall the new one use # A05-0303.
The cement is permanent so you're not going to be able to break it up. Instead you need to cut the pipes after removing the hose clamps. Then replace it with the new one and apply the new cement.
The same cement can be used on other plumbing parts as well. view full answer...
We have the LaSalle Bristol Eccentric Tank Reducer # 34466V153 which can slide over your 1-1/2 inch diameter gray pipe to give you a 3 inch pipe that you could then attach the 3 inch pipe to 3 inch bayonet adapter part # T1028 and you'd be set. view full answer...
You can definitely use the Valterra Bladex Waste Valve Body for RV Holding Tank # T1002VPM.
You're correct about the length not being a concern in regards to compatibility, what really matters is the 4-hole spacing, and for the Valterra # T1002VPM it is 2-7/8 inches, just like what you said you had.
With your measurements in regards to the extension, it sounds like you are saying you have a slip hub such as the Valterra RV Sewer Slip Hub with Flange - 2" # T1005-2 which has a 2-3/4"... view full answer...
The Projected Male Slip Fitting part # 372216-A-MS-A typically installs into the opening on the black water tank and then lets you attach a 3" diameter sewer pipe. view full answer...
The Camco RV Drain Trap for 3/4-Inch Diameter Drain Hoses, part # CAM37262, has a threaded portion for connection to your RV sink that measures 1-3/4-inches in diameter at the threads. The overall diameter of the mounting flange is 2-5/8-inches. The linked photo shows these dimensions. view full answer...
We can offer steps on how to determine the correct black tank valve, though unfortunately isn't a way for us to know the exact valve that is on your Montana 5th wheel. To determine the right one is pretty easy, as you just need to know if the valve you are replacing slid over your pipe or into your pipe.
If both ends of your waste valve slid into your sewer pipe you will need the Valterra Bladex Waste Valve for RV Black Water Tank - 3" Spigot to 3" Spigot # T40A.
If both ends of your... view full answer...
The Flush King Reverse Flush Valve # F02-4350 should work great for you but I do not recommend permanently mounting it. I have heard of some people doing this but to get the best, longest-lasting use out of this I highly recommend only using it when needed as opposed to keeping it on when you are traveling.
I have added a link to a video review of the Flush King for you to take a look at. view full answer...
The LaSalle Bristol RV Sewer Termination Adapter # 34466V293B3S is designed to slide into a larger hub like what you see on the end of # T1028 and secured using ABS Solvent Cement # 3447530889. The inner diameter on the hub should be about 3-1/2 inches. If this is what is on the PVC pipe that you mentioned then it will work great.
I don't recommend connecting it directly to another 3 inch diameter PVC pipe though, as this might not allow for the best connection even when using a healthy... view full answer...
The Camco RV Drain Trap part # CAM37262 that you referenced attaches directly to the sink. If would replace any style of trap that you have installed currently.
You could use a basket strainer with this as long as it would fit it's 1-3/4 inch diameter. view full answer...
The Valterra DWV Adapter for RV Sewer System # D50-2929 will fit with other 3 inch ABS threaded fittings. You will want to use Valterra ABS Solvent Cement - 1/4 Pint # A05-0303 to secure the end that is not threaded to the connected pipe. view full answer...
To attach the Valterra Eccentric Tank Reducer # T1041-1 to the rest of the plumbing on the RV and prevent leaks use the Valterra ABS Solvent Cement # A05-0303. It was made for exactly this purpose! view full answer...
Thank you for the photo, and there should be sensors with a monitor for your tank that tells you how full it is in order to use the Flush Valve for RV Holding Tanks and Sewer Hoses # F02-4350.
If you don't have that, you can still use the Flush Valve # F02-4350 but you'll want to be sure to limit the water flow going in so you don't have a real mess. But really, this is best used with black water tanks that have monitors which tell you how full it is.
This will work for you unless... view full answer...
The 1-1/2 inch gray water pipe you need is not something we carry. We do however carry the connectors, fittings, and valves. I've linked the pages to those fittings but the drain pipe lengths you will need to obtain from a local home improvement store. You will use the LaSalle Bristol ABS Solvent Cement - Black - 1/2 Pint # 3447530889 for those connections. view full answer...
The inner diameter of the Valterra Double Elbow DWV Fitting for RV Sewer System - 90-Degree - 3" Hub # D50-3047 is 3-1/2 inches. This will give you an outer diameter at the top of 3-7/8 inches. I've attached a video to help further.
You will want to use ABS solvent cement # A05-0303 to bond this fitting to your pipes. view full answer...
The Easy Slip RV Gray-Water Drain Adapter # CAM39111 will work, but I recommend the Valterra Gray Water Drain Adapter for RV Black Water Waste Valve # T1020-5VP. This will give you a cleanout for your black water tank. view full answer...
The EZ Coupler 4-in-1 Threaded RV Sewer Adapter with 90-Degree Elbow Fitting - Red Item # F02-3305VP comes with the cap for the end that drops into the dump station tube. Typically once you install the fitting onto your hose it doesn't need to be removed you would just place the cap on the open end when you are done draining your tanks. view full answer...
We do have a different option than the Camco Y-connector you are referencing, which is the Camco RhinoFLEX RV Sewer Hose "Y" Fitting # CAM39812. While most people have favorable reviews for the RhinoFLEX, I have seen similar comments as yours that under pressure there can be slight leaks. So what I recommend using as a replacement is the Valterra Rotating "Y" Sewer Connector # F02-2030.
The Valterra is a heavier-duty connector than the Camco that has internal seals (see accompanying... view full answer...
The big thing you need to determine is the diameter of the hose that feeds to your current sink trap. If it's 3/4 inch the part # CAM37262 would fit and work well.
I also attached a diagram that shows the opening dimensions as well for you to compare. view full answer...
It seems like you're looking for a coupling like this one # F02-2104. It has two clamps and will go in between both your grey and black water tank and the rest of your waste system. view full answer...
The Camco RV Drain Trap, part # CAM37262 is designed for 3/4 inch diameter drain hoses.
The threaded inlet portion of the trap measures 1-3/4 inches at the threads as shown in the attached photo. If your drain hose is 3/4 inches in diameter I am sure you could make this work for you. You may have to enlarge your drain to get this to fit and replace. view full answer...
There is Schedule 20 and 40 sewer pipe that has an outer diameter of 3-1/2 inches like what the Valterra Rotating Adapter for Rigid RV Sewer Pipe # T1028 is designed to work with so yes it would fit if the size was correct. view full answer...
I went out to our warehouse and pulled Camco Dual Flush Pro # CAM39062 to measure the length for you. The overall length from end to end is 8-5/16 inches. I have included a picture showing where I measured. view full answer...
The URL's you posted for for the same item so I'm assuming you meant to reference the Camco RV Drain Trap for 3/4" Diameter Drain Hose # CAM37262 and the Exterior Evacuation Drain Trap # 37295195.
Both of these drain traps are exactly the same with a standard 3/4" MPT water hose connection and 1-3/4" standard strainer connection. The only difference between the two is just the brand.
view full answer...
It sounds like you are looking for the Valterra Eccentric Tank Reducer part # T1041-1 which installs in an RV gray water tank with with 3" diameter opening and then reduces this down to 1-1/2". The adapter will install inside the neck on the tank and then secured with gasket maker part # LT37467 and a band clamp part # H03-0009. In order to replace the waste valves you can then use the Double RV Waste Valves part # T80A depending on your setup. Please note, you'll also need the Valterra... view full answer...
It is unknown what that white material is. It is probably some kind of glue used by the manufacturer. We recommend the Valtera # A05-0303 Solvent Cement for these types of connections. Be sure to clean the joints before applying the cement.
view full answer...
The threaded portion of the Camco RV Drain Trap, part # CAM37262 is 1-3/4 inches.
I called my contact at Camco and they told me the threads are 1-1/2 - 11.5 NPSL. My contact at Camco said the information came from the engineers and they were unable to tell me much about this size. The information I found online is that NPSL means National Pipe Straight Locknut, but I was not able to find more information about the 1-1/2-11.5.
view full answer...
The RV Reducing Y # T1014 has 3" lug to a 3" stationary flange and a 1-1/2" rotating flange. The relative position of the flanges is not critical and will fit most black and grey water tank connections. You might want to use # T1014-1 which has rotating flanges for both your black and grey water connections. Check out the videos linked below for more details on these products. view full answer...
The diameter of the threaded portion of the # CAM37262 is 1-3/4 inches which is a very common size and hopefully what you need for your camper. view full answer...
The outer diameter (O.D.) of the end opposite the flange on the Valterra RV Sewer Elbow part # T1035-2 measures 3-7/16" therefore if the inner diameter (I.D.) of the outlet on your black water tank is 3-7/16" then it will work for you. If not you would need to purchase an adapter at your local plumbing store. In order to attach the pipes I recommend using the Valterra ABS Solvent Cement part # A05-0303. view full answer...
If you are using the most common type dump hose out there, perhaps different in appearance but size wise, the same that almost everyone else at the camp site has, then yes. The EZ Coupler 4-in-1 RV Sewer Adapter with 90-Degree Elbow Fitting, # F02-3103 fits 3" slip and 3", 3-1/2", and 4" threaded sewer inlets. view full answer...
Yes, the "Y" part of the Valterra "Y" DWV Fitting # D50-2824 sits at a 45 degree angle. You could add a 45 degree elbow like part # D50-2892 and your pipes would be running parallel. view full answer...
If you plan on using Camco Dual Flush Adapter for Rinsing RV Holding Tanks and Sewer Hoses
Item # CAM39072 for its designed purpose than it would need pressure in order to rinse the tanks and activate the jets. If you are using it as an adapter of sorts then it should not need the pressure and liquid would just flow through it but not activate the jets. view full answer...
Yes you can use the Lippert Components Tote Tank Adapter # LC360789 to go from your bayonet connection to an end that works with the Camlock Connector # LC360578. view full answer...
We do have what you are looking for as the part # T1009. This will replace the flange side of your waste valve that you sent in a picture of and give you bayonet fittings you can attach to your sewer lines. It's hard to say but it looks like yours may have been broken off. view full answer...
The attached image was helpful in easily identifying exactly what measurement you wanting on the Valterra RV Sewer Elbow with Rotating Flange, # T1035-2. It is 5-5/16". view full answer...
As long as the RV sewer hoses are 3 inch in diameter without a bayonet fitting like Camco part # CAM39611 the hoses will slide over each end of the coupler part # CAM39203 to join them together. You do not need to heat the coupler up to seal the connection. view full answer...
I contacted the manufacturer and the Valterra RV Sewer Termination Adapter, Item # T1029-2, fits standard ABS sewer pipes for RV uses. It is made from a very sturdy plastic and you would use something like ABS Solvent Cement, Item # A05-0303, to join the pieces. view full answer...
What I recommend to flush your gray water tank is the Tornado 360-Degree RV Holding Tank Rinser # CAM40126. Install this into the tank, connect a hose, and flush out the tank! I have included a link to a video review of this product for you. view full answer...
Since you are wanting the # T1011 with a 2 inch tee on the side instead you would want the part # T1012 as this is same configuration with the sizes you want. view full answer...
Yes, the Valterra RV Sewer Spigot with Flange # T1006 does fit into the Valterra Double Elbow DWV Fitting for RV Sewer System # D50-3047 which has hub fittings that spigots fit into. view full answer...
Yes, the Valterra DWV Adapter # D50-2929 fits the standard 3 inch RV black water piping like you have currently so it would work well. To install it you will need solvent like part # A05-0303 as well. view full answer...
The LaSalle Bristol RV Sewer Slip Hub with Flange part # 34466V13 has an outer diameter of 3-3/16". That said, this adapter has a hub style connection which means it is designed so that a 3" diameter pipe can slide into the orifice. view full answer...
The Valterra Adapter for RV Sewer Hose part # T1025VP has a bayonet fitting on one end and then a tapered fitting on the other end. There would be no way to attach a 3" pipe to the tapered fitting but what you could do is combine the Valterra Street DWV Fitting part # D50-2892 and the Valterra Rotating Adapter part # T1028 to provide a bayonet fitting on one end and then a hub fitting on the other which you would then slide a 3" pipe into.
Please note, RV's use ABS pipe construction... view full answer...
I have attached a list of all the sewer fittings we offer from LaSalle Bristol for you. I was not able to identify the specific fitting you inquired about but if you can send me a photo, I will try to see if we have the proper replacement for you. view full answer...
The Camco RV Drain Trap, part # CAM37262 is designed for 3/4 inch diameter drain hoses.
The threaded inlet portion of the trap measures 1-3/4 inches at the threads. view full answer...
The Valterra DWV Adapter for RV Sewer System, # D50-2929, installs into your RV's 3 inch waste valve system. If your tank hub is threaded as such, yes. Note that this is the internal diameter at 3". The outer threaded section is about 3-1/2". view full answer...
The Camco RV Drain Trap # CAM37262 or # CAM37420 is designed to be used with a 1-1/2 inch - 11.5 threaded drain fitting. I recommend the Valterra Sink Drain with Strainer Basket # A01-2011VP or the LaSalle Bristol RV Drain with Strainer Basket - Metal - 1-1/2" Diameter # 34433JN1201 for this compatibility. view full answer...
In most cases the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1 is going to be attached to the gray water tank with an ABS solvent like # A05-0303, so it will need to be cut off in order to replace it. view full answer...
To connect your RV to a 4 inch PVC pipe, I recommend the EZ Coupler 4-in-1 Threaded RV Sewer Adapter with 90-Degree Elbow Fitting - Clear # F02-3112CL. This adapter will transition from the standard 3 inch RV black water connections to the threaded 4 inch PVC.
For your 3 inch connections, you may be interested in the Camco RV Sewer Hose Straight Adapters w/ Bayonet and Lug Fittings and Clamps # CAM39543. To get your two lines into one, you may want the RhinoFLEX RV Sewer Hose "Y"... view full answer...
When not in use you would want to remove all of the RhinoFLEX Rhino Blaster Pro Adapter for Rinsing RV Holding Tanks and Sewer Hoses # CAM39085 from the RV so that you don't end up damaging it as it can hang pretty low.
I attached a demo video for this for you to check out as well that shows how it installs. view full answer...
The Valterra RV Sewer Spigot with Flange - 3" # T1006 will be compatible with LaSalle Bristol Valves. This has the standard mounting holes 3-3/4 inches apart on center. Then you will simply use the solvent cement like # A05-0303 or # 3447530889 to bond the spigot to your tubing view full answer...
If you check out the video link I attached you can see where our demo guy measures the larger side of the T10401-2 and it has an outer diameter of 3-1/2 inches and an inner diameter of 3 inches. Right at the 29 second mark you can see the ruler held up to the product so you know he isn't mistaken.
That end is going to fit over a 3 inch sewer pipe like you mentioned. view full answer...
Yes the Valterra Hose Adapter w/ 3" Swivel Lug Fitting part # F02-2028VP will be a suitable replacement for your needs so long as your pipe coming out is 3" inside diameter. You will remove the old one clean up the end on the old pipe to ensure it is free of burrs and give it a light sanding. You then can use Valterra ABS Solvent Cement part # A05-0303 to make your connection with your new adapter. I've included a link to a video Conner was lucky enough to get to do here to show how the... view full answer...
Using PVC (white pipe) between ABS fittings (black) is not usually an optimal setup on a trailer because of the movement during transport and colder temperatures can cause PVC to break more easily.
The Oatey Purple is a PVC primer and not a glue so it wouldn't adhere correctly. Using a green transition glue as well as the purple primer on the PVC pipe could have worked however. Ideally they should have used black ABS pipe between the fittings and used ABS cement like LaSalle Bristol... view full answer...
I went out to the warehouse and verified that one of the hubs is 2" while the other is 1-1/2" for the Double RV Sanitary Tee # T1013. I sent an update for this to be changed, thank you.
Attached is a review video where this is highlighted as well. view full answer...
I went out to our warehouse to measure the Valterra Hose Adapter w/ 3" Bayonet and Swivel Lug Fitting # F02-2029VP that you referenced. I found that the lug fitting has an overall diameter, at its widest point, of 4-1/4 inches (which includes the attachment nibs). The standard bayonet fitting has an overall outside diameter of 4-1/8 inches.
I have attached an image to assist.
If your storage compartment has an inside diameter of exactly 4 inches these likely won't fit too well.... view full answer...
I spoke with my contact at Camoco, and she verified that it is fine for you to leave the Dual Flush Pro # CAM39062 on your trailer.
In the winter months, make sure to keep the Dual Flush Pro clear of water and other liquids so as to not damage or crack the product due to freezing.
view full answer...
I recommend using the Valterra Gray Water Drain Connector # T01-0091VP you mentioned. This has a 1-/1/2" FPT connector on one end, and a 3/4" MPT fitting on the other end to connect to a flushing hose like # W01-4300.
The # T01-0091VP keeps a low profile at 2-5/8" tall which should be small enough to fit in any space you need it. view full answer...
The RV Sewer Slip Hub part # 34466V13 that you referenced has 3-3/4 inches between all of the mounting holes like you are looking for so it would work great. view full answer...
The Valterra ABS Solvent Cement part # A05-0303 can be used in any temperature within reason. That said, the lower the temp the longer cure time it will require. The ideal temperature is 60 degrees Fahrenheit. There is no max or min temperature in the instructions. view full answer...
When installing the # CAM37262 you need to unscrew the top half of the drain trap from the bottom half and screw it onto your 1-3/4" drain tightly and then you can attach the bottom portion back on to the top using two of the four mounting spots with the two screws provided to position the 3/4" drain hole in the direction you need it in. You can use some plumbers putty as extra protection but with the threads tight and the rubber gasket you should be fine. view full answer...
The Flush King Reverse Flush Valve # F02-4350 that you referenced gets connected to your bayonet sewer fitting and used and then removed when not in use. I would not recommend leaving it installed all the time. view full answer...
It is challenging to know for certain if the Camco RV Drain Trap for 3/4" Diameter Drain Hose, # CAM37262 will help in this situation. I do see it as a cost effective attempt. I think best long term would be to reroute the drain lines to more aggressive angles with more direct flow to holding tank, if this is possible. I would attempt these routes before installing a pump.
view full answer...
Go To Results