One SoftStartRV Soft Start for each RV AC Units # SSR54FR is required regardless of the power supply. The SoftStartRV provides a reduction in STARTING AMPS not RUNNING AMPS.
Typically starting amps can be as high as 50 to 70 amps. The SoftStartRV will cut the starting amps down to approx 25. You need one SoftStartRV for each A/C compressor. I attached a demonstration video which goes into more detail on this soft starter. view full answer...
All you need is the 15k BTU Atwood AC kit part # AT15033-22 which comes with the thermostat, roof vent, and a heat pump like you are wanting. view full answer...
Yes, the ball mount in the Curt Trailer Hitch Towing Starter Kit, item # C45534 can indeed be used in the rise position. When in the rise position, the ball mount provides a 3/4 inch rise. view full answer...
The Curt ATV Towing Starter Kit # C45038 is designed to work on any ATV that has a tongue area for mounting a hitch ball with a 3/4-inch hole diameter. The receiver portion with the tow strap loop uses an included 3/4-inch bolt to install in that hole. This kit includes the 5/8-inch hitch pin and clip to secure the included ball mount component into the bolt-on receiver part.
This can be used with a tow strap such as the 20-foot # EM59798. view full answer...
For a 1-7/8" ball that is compatible with the Curt Towing Starter Kit for 2" Hitches item # C45534 you will want the Draw-Tite item # 19260. view full answer...
The Curt Towing Starter Kit part # C45534 comes with the Curt Ball Mount part # C45030 which accepts hitch balls that have a 1" shank. view full answer...
Reese Trailer Hitch Starter Ball Mount Kit # RP7043000 has a 3/4-inch hole for the shank of the included and pre-installed 2-inch hitch ball. view full answer...
I'm not 100 percent sure I know the exact dimension you are referring to by center of the hitch pin hole to where you slide the mount up to the receiver, but I believe you are asking about the hitch pin hole to the rear of the Curt Towing Starter Kit for 2" Hitches # C45554.
It is approximately 2-1/2" from the center of the hitch pin hole to the rear of the ball mount, and 8-1/4" from the center of the hitch pin hole to the center of the hitch ball.
I have added links to a pair of video... view full answer...
That's an excellent question and the Redarc In-Vehicle BCDC Battery Charger - Dual Input - DC to DC - 12V/24V - 25 Amp # 331-BCDC1225D does require a connection to your starter battery as opposed to your 7-way; additionally you do need the 40-Amp MIDI Fuse Kit for Redarc In-Vehicle 25-Amp BCDC Battery Charger # 331-FK40. The reason is this kit makes sure you do not get a short or overload your system.
I have added links to video reviews for you to take a look at of both the charger and... view full answer...
If you have a 2 inch receiver opening on your 2013 Dodge Ram with the factory hitch, I recommend the etrailer.com ball mount kit, part # 989900.
This kit comes with 2 balls, 2 ball mounts, the pin and clip, and a handy storage bag. I have attached a product review video for this ball mount kit you can check out.
We do not offer a Curt towing starter kit. view full answer...
Yes, we do have Replacement Battery Clamps # NOC69FR for your NOCO Boost Max Jump Starter # 329-GB500. We do also have them available in 72" Cables # NOC79FR if you find the 24" cables are difficult to use. view full answer...
Yes, it will drain the battery. Pressing the ignition button without first depressing the brake pedal will set the vehicles electrical system into accessory mode; same as in a keyed ignition vehicle turning the key forward but not to the point of engaging the starter motor. However, if needed, this is why we have the Roadmaster Battery Charge Line Kit for Towed Vehicles, # RM-156-25. This kit allows up to 15 amps from your RV's battery to be used to maintain the charge of your towed car's... view full answer...
The amount of torque needed to secure the nut of the ball on the Reese Trailer Hitch Starter Ball Mount Kit # RP7043000 that you referenced is 160 ft lbs. view full answer...
Yes the ball mount included with the Curt Towing Starter Kit for 2" Hitches part # C45534 can be flipped over. You will need to remove the ball of course and place it on the other side. This should be torqued down to 250 ft/lbs. when installing it. view full answer...
Is this occurring when the vehicle's being flat towed, or when it's being driven, or both?
If it's occurring only when the vehicle's being flat towed, it's possible that operating the towed vehicle's turn signals is too much for the electrical system of the RV. Try replacing the existing flasher with a heavy duty model.
If it's happening only when the vehicle's being driven, there's several different reasons why this is happening. I'd need to know which wiring kit you used and whether... view full answer...
Yes, you can install a trailer hitch on a Coleman Lite 2955RL Trailer Trailer. In order to do this you have a few options. The first is a bumper mount hitch which bolts onto the bumper, the Curt RV Bumper Hitch part # C19101. This is a good option for bike racks or other hitch mounted accessories but isn't great for towing and would likely require bracing of the factory bumper if used in such manor. Instead, I recommend a frame mounted trailer hitch which is much stronger, the Adjustable... view full answer...
When towing your 2019 Chevrolet Equinox behind your motorhome, to keep your Equinox battery charged you would need The Roadmaster Battery Charge Line Kit for Towed Vehicles # RM-156-25. This part maintains the battery charge in your towed vehicle while the car is being towed. The charge line kit connects to the 6-way or 7-way plug on your vehicle. The cable is 14-guage.
This requires the Roadmaster's motor home battery line # RM-156-75 which is sold separately, if no charge line is present... view full answer...
The Keystone Montana series of 5th wheel trailers uses a specific landing gear kit from Lippert Components, the company that built the RV frame.
For a replacement Lead Leg use part # LC178653; for a replacement Follow Leg use part # LC178652. For a new gearbox use part # LG-179015 and for a motor kit if needed use part # LG-196308 that you referenced. view full answer...
Yes and no, if you need to tow a trailer with brakes and are okay with using a wireless trailer brake controller, which is what I recommend, then I do have an option for you that won't require cutting or splicing into the vehicle's wires. That said, you will need to splice a few wires together in the kit but you're just doing this to extend them and again, it's not the vehicle's wires so you can remove everything without modifying. In order to do this you'll need a few parts which I have... view full answer...
Go To Results