bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about RV and Camper Steps


  • Lippert SolidStep Fit for 28 Inch Wide Door and 38 Inch Entry Height
  • The best Lippert SolidStep for you RV with a door frame that measures 28 inches and an entry height of 38 inches is the SolidStep Manual Fold-Down Steps for 26" to 29-7/8" RV Door Frames # LC791574, which, as you can see by the name of the product, is perfect for your 28 inch door frame. It is also designed to fit entry heights between 35 inches and 44 inches, which it can do because it has adjustable let extensions. These steps do not come with mounting hardware but you will only need...
    view full answer...

  • MORryde StepAbove Fold-Down Steps for 2018 Montana Fifth Wheel
  • Since the distance from your threshold to the ground is 38", and the narrowest part of your door is 28-1/4" side-to-side, the MORryde steps that are a fit for you are the MORryde # MR28RR steps featuring 8" deep steps. Optionally you could also use the MORryde # MR85RR steps which are the same as the MR28RR's except they feature gas lift struts that allow you to lift of lower the steps with one finger! If these steps are replacing traditional fold in steps you should consider the...
    view full answer...

  • Motor Replacement for Kwikee Step Motor Number 903209000
  • Are you sure that's the number you found? I can't find any references to it anywhere.
    view full answer...

  • TorkLift Glowstep Revolution Size Selection
  • Since you have the 27" wide entryway, the only additional thing we need to know is the "Entry Height." The attached photo will show you how to measure from the top mounting point to the ground. From there use the attached chart. For instance if your entry height was 38" high, then you would use # TLA8004. Watch this though: If your entry height was 36" then you could use # TLA8004 or # TLA8003. The steps for taller entryways will extend out further. The steps for shorter entryways...
    view full answer...

  • Differences Between MORryde StepAbove Fold-Down Steps MR98RR and MR48RR
  • You are right on. The 8" rise/drop on the MORryde StepAbove Fold-Down Steps # MR98RR is the height between the steps. The # MR48RR you were looking at has a 9" rise/drop meaning the distance between the steps is 9". The # MR98RR is designed for RVs with a 23-3/4" - 26-1/4" wide door frame, and requires and entry height between 30" - 33-1/2", and the # MR48RR is designed for RVs with the same 23-3/4" - 26-1/4" wide door frame, but is used when the entry height is between 34" - 36". Entry...
    view full answer...

  • Installation Bracket Locations for Lippert Victory Fold-Down Steps
  • The Victory Step Manual Fold-Down Steps for RV and Toy Hauler Patios - Quadruple - Aluminum # LC726895 you asked about will only allow for about 3 inches from the edge. For your application you would either need to add a piece that is hinged to flip out over the door frame or add a piece to the outer door frame to hold the brackets and weight. This could look similar to the Lippert Components Garage Storage Brackets for Victory Step Manual Fold-Down RV Steps - Wall Mount # LC726890 but...
    view full answer...

  • Torklift GlowStep Replacement Support Bracket and Bolt
  • I have a solution for you but we don't have a replacement bracket to replace the support and bolt that was broken on your TorkLift GlowStep similar to the # TLA8004 . Instead you would need to use the Add-A-Step for TorkLift GlowStep Revolution Scissor Steps # TLA8101 which will work on any TorkLift GlowStep models with the 25-7/16" wide mounting base. You can use the parts in this kit to replace your broken parts or replace an entire step. If you have the 27-7/16" mounting base model...
    view full answer...

  • How To Measure Doorway Width for Lippert SolidSteps On a Grand Design Solitude
  • In order to choose the correct SolidStep Manual Fold-Down Steps you will need to measure the opening of your doorway inside the trim pieces. I have attached a photo to show this. If the threshold height is over 35" when measuring from the ground while level to the bottom of the doorway then you can indeed use a quad step. For this we have part # LC678025 for 26" doorways, part # LC791574 for 26"-30" doorways, and part # LC791575 for 30" - 36" doorways.
    view full answer...

  • Manual RV Steps for 24 Inch Wide Door Frame with 6 Inch Rise/Drop Between Steps
  • Thank you for all the information; that allowed me to do quite a bit of research. To answer your questions in regard to the Lippert SolidStep, there isn't a 4-step version of # LC698799, which is a triple step that fits 24 inch wide door frames. Additionally, there isn't an option to add an extra step, nor are they sold separately. Therefore, according to my contact at Lippert, if you were to take on such a project, you'd need to provide your own parts and come up with a plan to execute...
    view full answer...

  • Fold Out Camper Steps for 24" Wide Door and 27"-36" Entry Height
  • The Lippert # LC698799 is no longer available however the MORryde # MR98RR is a better choice for doors with thresholds 30" to 33" off the ground and doorway widths of 23-3/4" to 26-1/4". Depending on your measuerments the MORryde # MR26RR is good for thresholds 25" to 29" off the ground and doorway widths of 23-3/4" to 26-1/4". Either way these steps are large and ensure a safer entry to your trailer with out the disturbing trailer roll that standard steps cause. If you are removing...
    view full answer...

  • How To Mount TorkLift GlowStep Stow N' Go Steps To Camper With 9" Deep Bumper
  • I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear # TLA7843 away from your camper to clear your bumper. It may be possible to have a local fabrication shop make a custom bracket for your application. Instead I recommend installing the # TLA7843 to the bumper of your camper as shown in the included pictures, this will allow you to still use the step, but will not require a...
    view full answer...

  • Replacement Gear and Parts for Original Lippert 3 Step on 2008 Forest River Georgetown 373
  • For the replacement gear you will use the Replacement Entry Step Gear for Lippert Kwikee 25 and 26 Series Triple Steps # LC369354. I believe the shear pin you are referring to is a part of the gear itself. The motor is # LC369506 which comes with the smaller gear. If you want to replace the entire assembly you can use the Lippert Components Kwikee Step Replacement Kit # LC379804.
    view full answer...

  • Difference Between Kwikee 40 Series RV Steps # LC3726892 and # LC3726891
  • There is a slight difference between the # LC3726892 and # LC3726891. The # LC3726892 comes with a control switch setup that allows the light and step to come on and off with the opening and closing of the door.
    view full answer...

  • Handrail For Use With Lippert SolidStep Entry Steps
  • We do have handrails that are going to allow for an easier way for your mom to get up the steps and into your 2016 Heartland Cyclone, the issue with changing from the Lippert SolidStep Manual Fold-Down Steps # LC791574 to a TorkLift GlowStep is the mounting brackets because none of the GlowSteps share the same mounting bracket dimensions as the Lippert steps. What I recommend instead is keeping your current steps and instead adding a very good handrail, the Lippert Entry Assist Handrail...
    view full answer...

  • Lippert SolidSteps for 2021 Forest River Surveyor Legend 18RBLE
  • To measure for fit of the Lippert SolidStep, measure the entry way from right to left at the narrowest point. Generally there will be a flat metal flange that extends out 1/2" all around. This is the flange that the door closes against and keeps the door from trying to swing inside. From that measurement, round up to the next even inch. So, your door (at the narrowest point) is 21-1/4" wide to the door flange, and rounded up we get 23". The narrowest width for solid steps is 24 inches....
    view full answer...

  • Will Screen Door and Entry Door Close Normally with SolidSteps in Place?
  • When the Lippert # LC791572 steps are properly installed with the threshold plate firmly against the outside threshold you should have no issues. The only thing we hear from customers is how much they love them! While you have your tools out you might as well take down those old stock rattle-trap steps that came stock on your trailer and install the Lippert # LC664640 locking steel box just made to fit in the spot where the steps were. Great spot for black water supplies, or roadside...
    view full answer...

  • Solid Step Fold-Down Steps for RV Compatibility with Screen Door Bar
  • The SolidStep Manual Fold-Down Steps for 26" to 29-7/8" RV Door Frames - Quad - Aluminum # LC791574 will work fine with most screen door bars like the Camco Deluxe RV Screen Door Cross Bar - 21-1/4" long to 28-5/8" long - Aluminum - Black # CAM42183 that sounds similar to your description. You won't have issue with the bar if it is just above the plastic bubble cover slide as you stated.
    view full answer...

  • Picking Out Correct Lippert 2-Step SolidStep Assembly for 2018 Rockwood Mini Lite Trailer
  • The Lippert SolidStep Fold-Down Steps like the 2-Step # LC733931 you were looking at are designed to fit specific doorway widths. Unfortunately trailer manufacturers don't make dimensions like this available so you will need to take a quick measurement of the inside door width on your Rockwood Mini Lite to determine the correct model. This particular SolidStep model will fit doorway widths of 26" to 29-7/8". Also make sure that your entry height (height from the ground to the door)...
    view full answer...

  • Solution for Kwikee RV Electric Steps that Work in Reverse After Installed
  • We're familiar with this issue which happens when the incorrect switch is used. Kwikee Steps use two different magnetic switches. One is a normally open circuit and the other is normally closed circuit. The switch must match the controller. Otherwise, the steps will work in reverse, as you described. The original switch kit included with the newer Kwikee 32 Series Electric RV Steps # LC372261 is an open circuit. The two magnetic sensor tabs mount in the doorframe and on the door. When...
    view full answer...

  • 2 Step Solution For A Forest River Wildwood 171RBXL
  • For your Forest River Wildwood X-Lite 171RBXL you are looking for the SolidStep Manual Fold-Down Steps as your solution. Which part number you need will depend on your doorway width. If you have a door frame width of 26" - 29-7/8, you'll want the 26" - 29-7/8" Wide RV Door Frames part # LC733931 or part # LC713662 for 24" wide door frames. Included is an installed example for reference.
    view full answer...

  • Do Fold-Out Steps Need to be Removed When Mounting Brophy Scissor Steps
  • That is a good question, and you can leave your current fold-out steps up and in the folded position when installing the mounting bracket of the Brophy Scissor Steps. The reason is, the bracket will be installed just underneath the door so as long as when your steps are folded up there is no interference in that area the Brophy steps will be a great option. I added a photo for you a customer sent in which shows the bracket and steps installed so you can get an idea of how they mount. The...
    view full answer...

  • Comparing Camper Scissor Steps Brophy AS24 vs. Torklift TLA7804
  • Both the Brophy # AS24 and the TorkLift # TLA7804 are easily removed when not in use- and it's actually recommended that you do so. Additionally, they both weigh in around 26-lbs total, so they're easy to move on and off; so they'd both be great choices for what you're looking for. Overall I prefer the TorkLift # TLA7804 because of the quality of TorkLift products in general, plus you'll have the ability to add the All Terrain Landing Gear for TorkLift GlowStep Scissor Steps for RVs...
    view full answer...

  • Is There a Replacement Gearbox and Motor for 1989 Electric Step
  • So while we do have some options for you, there are no longer specific motors and gearboxes for electric steps manufactured before 1999, so for your 1989 Pace Arrow, what you will likely need is a motor upgrade kit, which includes the motor, linkage, control unit, switch kit, and hardware for installation. Keep in mind that this would only be for specific Kwikee steps, with the right one depending on the series of Kwikee step you have. - Kwikee Series 22, 23, 28A, 30, 32, 33, 34,...
    view full answer...

  • How Much Clearance is Needed Between Entry Door and Threshold of RV for MORryde StepAbove
  • The standard clearance requirement for the MORryde StepAbove RV steps like part # MR88RR is 3/8 of an inch which is the same for the # MR28RR.
    view full answer...

  • Could Torklift GlowStep Scissor Step Fit 2018 Lance Truck Camper 825
  • What's the entry height of your Lance? I am sure we have a set of the Torklift Glowsteps that will work but we need to know for sure the entry height to pick out right size. For example, the part # TLA7844 fits the height range of 31-42 inches. And the part # TLA7845 fits the height range of 38-1/2" - 50".
    view full answer...

  • Fitment of Brophy Camper Scissor Steps for Truck Campers
  • The Brophy Camper Scissor Steps for truck campers, # AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points and chart.
    view full answer...

  • Troubleshooting Kwikee 42 Series Step that Motor Continues to Run for 2-3 Seconds After Steps Extend
  • It could be that your Kwikee Series 42 Steps # LC372779 are just hanging up and bit and could use some lubricating spray on the gears; you'll want to use a dry silicone spray on these parts similar to the Roadmaster Lube Master # RM-747 to keep everything in working order. With that being said, this is also a sign that the motor on your Kwikee Series 42 steps could be weakening, so you'll want to keep an eye on this going forward. If it ends up that the motor goes out on your steps...
    view full answer...

  • Will Torklift RV GlowSteps TLA7834 Fit 2017 Forest River Flagstaff Classic 832BHDS
  • To determine if you are able to replace your 3-step unit with a 4-step unit like # TLA7834, you will need to take a few measurements as RV steps are not custom to the year, make and model of a specific RV. Measure from the ground to the top of the threshold on your RV to determine how much ground clearance you have. The Torklift Steps require ground clearance between 31 and 42 inches. The mounting bracket base dimensions for the Torklift GlowSteps are 21-1/2" wide x 14-1/2" tall x...
    view full answer...

  • Torklift Replacement Steps for Grand Design Reflection 5th Wheel Including 303RLS
  • The Torklift # TLA8003 (3 Steps) will fit for your trailer. These are intended for a mounting bracket measuring 27-1/2" and an entry height of 25-1/2" to 36". Alternatively, the Torklift # TLA8004 (4 Steps) is designed for an entry height of 32-1/2" to 44" and will extend out further. If you have trouble on steps I would recommend the 4-step model, just know that they extend out further, otherwise the 3-step model is fine. Also check out the Torklift # TLA7621 Hand rail. 4 steps...
    view full answer...

  • Do MORryde StepAbove RV Steps MR26RR Fit 24 Inch Wide Doorway
  • The doorway width - the width from flange to flange of your doorway - needs to be between 23-3/4 inches and 26-1/4 inches, so yes, your 24 inch door will allow you to use the MORryde steps you asked about, which are the following part number: - MORryde StepAbove RV Steps - 2 Steps # MR26RR The only other thing you need to be sure of is the entry height (which is measured from the doorway threshold on your camper to the ground), as the # MR26RR is for entry heights measuring from 25...
    view full answer...

  • Replacement Motor and Gear Box for Kwikee 32 Series Steps 903209000
  • We have the exact motor and gear box you need for your Kwikee 903209000 steps, which are the Kwikee 32 Series Electric RV 2-Step # LC3722615. The replacement parts are the following: - Replacement Motor with Mounting Plate for Kwikee Electric RV Steps # LC379608 - Replacement Gear Box and A Linkage for Kwikee Electric RV Steps # LC379160
    view full answer...

  • Lippert Fold Down Solid Step for 2017 Coachman RL251
  • You will need two measurements to pick the perfect fitting Lippert fold down solid steps. First the door way width which is the distance between the narrowest part of the door, usually where the flanges stick out. See the picture on the product page. Second you will need to measure the "Entry Height," which is the height from the threshold at the bottom of the door to the ground. With these two number in hand refer to the chart of the product page. I have attached a copy of it here. For...
    view full answer...

  • Picking Out Torklift Glow Step That Fits Lance Model 1475
  • The TorkLift GlowStep Revolution Scissor Steps # TLA8004 that you referenced are designed to fit entry heights on RVs that are between 32-1/2 and 44 inches which which might be a little higher than what you have on your 2018 Lance 1475 based on the pictures I was able to find online of it, we don't have a way to get the exact threshold height of your RV so you'll have to take a quick measurement to verify. If you find you have lower height we have the part # TLA8102 which has two steps...
    view full answer...

  • TorkLift GlowStep Stow N' Go Scissor Steps for 2022 Arctic Fox 990 With Platform
  • The TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear, # TLA7834 is for an entry height of 31" - 42". Find the mounting spot for the bracket on your vehicle and measure from that point. The # TLA7835 part number is for height of 38-1/2" - 50". We also have available the TorkLift GlowGuide Handrail, # TLA7621, note linked product video. And the Pin Lock for TorkLift GlowStep Scissor Steps, # TLA7509. This replaces one of the pins that holds the scissor steps to the mounting...
    view full answer...

  • Troubleshooting Kwikee Power Step of RV that Opens When Driving in Rain
  • The water is creating a short for the door switch of the Kwikee 32 Series Electric RV Steps # LC372261 which is basically telling the module that the door is open when it's not. Either there's exposed wire between the door switch circuit which the water is creating a short or the module is allowing water to seep in and create the short there. The step light switch wiring should be purple and black. You might check to see if there's any exposed wiring you could potentially seal up better....
    view full answer...

  • Replacement Steps for SCS/Frigette 733-0074 On RV
  • I would be more than happy to help you find replacement steps for the Scs/Frigette 733-0074 steps on your 2008 Monaco Dynasty Renaissance IV! We don't have any exact conversions but we do have replacement 2-step steps that you can potentially use. You'll just want to choose the steps that fit your application best. The 42 Series Kwikee Step # LC372779 is 25-1/4" wide and has a mounting plate that is 30-1/4" wide x 24-11/16" deep. The 47 Series Kwikee Step # LC427247 is 26-1/4"...
    view full answer...

  • Lippert Solid Step Quad Steps Compatibility with Thresholds
  • By threshold I assume you are either talking about threshold height or how the SolidStep fits on a threshold. If it was the latter then these steps do need to rest on the threshold of the door frame; I have added a cut out of the instruction manual and if you read the part that says "NOTE" you will see where it specifies this. If you were talking about threshold height or doorway width, that is much simpler and will only require you to take a couple measurements. The SolidStep...
    view full answer...

  • Can You Add a Step to the TorkLift Glow Step Scissor Steps
  • Yes; there is a way to do this. In order to add a step to your TorkLift Glow Step # TLA7803 you can use the Single Add-On Step for TorkLift GlowStep Kits - 20" Long x 8" Deep # TLA7801. This adds a step in the middle and leaves the rest of the step in tact.
    view full answer...

  • Hand Rail For Lippert SolidStep Manual RV Steps
  • Yes, the Lippert Entry Assist Handrail for SolidStep Manual RV Steps part # LC799640 is the hand that you need for your SolidStep Manual Fold-Down Steps for 26" to 29-7/8" RV Door Frames part # LC791574. This hand rail fits third generation Triple or Quad SolidStep models. The Entry Assist Handrail can be easily removed or left in place when storing if clearance allows inside the trailer.
    view full answer...

  • Kwikee Magnet Switch for RV Step with 909506000 Module
  • The replacement door magnet switch kit for the auto retract/extend is the part # LC369299 as what you have requires a switch that is "normally open". This is an inexpensive solution that should fix your issue so I would start with it and see if it helps.
    view full answer...

  • Can Stow N' Go Scissor Steps be Installed on Camper Without a Bumper
  • While we do not have a video of these steps being specifically installed on your camper I took a look at the instruction manual, which is also linked, and there is a method for installing these steps on a camper that does not have a bumper. You would need to remove your current bracket and it would require a 19.5" x 3.5" mounting area below the door. The mounting bracket for each of these steps is 21-1/2" wide x 8-1/2" deep but its height is going to differ depending on the model you...
    view full answer...

  • replacement stairs for Eagle Cap 1165 Truck Camper
  • You will need two measurements to determine the best fit for your camper. First is the "Entry Height". This is the measurement from the top of the mounting bracket to the ground. See the example picture on the product page. The TorkLift # TLA8006 that you referenced is suitable for entry heights between 46-1/2" to 60". The second measurement is the "Mounting Bracket Width". With the old steps removed, there will be a black metal mounting bracket that held the old steps. If yours measures...
    view full answer...

  • MORryde StepAbove Fold Down Step for Forest River Salem 178bhskx
  • Since your threshold is 28-1/2 inches tall from the ground and your doorway width is 24 inches the correct MORryde StepAbove is the part # MR26RR. The three step options like the # MR98RR would be too tall and wouldn't fold down all the way so they wouldn't work.
    view full answer...

  • Recommended Lippert SolidStep for a 2014 Keystone Montana 3402RL
  • I am not sure who you spoke with at Lippert but what they told you about using the 26" wide SolidStep # LC791574 was incorrect. When I spoke with my contact he said that whether you have the 29-3/8" or 28-1/4" wide frame you want to use the 30" SolidStep # LC791575 that we referenced in a previous answer. Reason being that there is no SolidStep for a 29" wide door frame so you simply round up. When the SolidStep first came out there was conflicting information regarding fits but I believe...
    view full answer...

  • Recommended Replacement Steps For 2017 Forest River Sandstorm 27
  • I can absolutely recommend a set of replacement steps for your 2017 Forest River Sandstorm 27 but you will need to do a quick measurement of your entry height to confirm the correct model as we unfortunately do not have a way of checking the entry height on your RV. I recommend the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear which you will need # TLA8104 if your entry height is between 32-1/2" - 44", # TLA8103 if your entry height is between 25-1/2" - 36", or # TLA8102...
    view full answer...

  • Handrail for Second Generation MORryde StepAbove
  • For your Second Generation MORryde StepAbove, please take a look at the, # MR83AR. This is designed specifically for the steps you have.
    view full answer...

  • Which Torklift GlowStep Set Would Work Best on Doorway Height of RV that is 40 inches
  • Thanks for the pictures of your steps on your RV. Right now it looks like you have the Lippert Manual Pull Out Steps part # LC432690. So for a similar Torklift GlowStep setup that would match the threshold height you have now of 40 inches you'd be best off with the 5-step part # TLA9105 which has a entry height range of between 34-7/8" to 42-3/8".
    view full answer...

  • Door Clearance of Morryde Steps for 2014 Open Range 399BHS
  • As long as the doorway opens at least 90 degrees the MORryde StepAbove RV Steps, # MR98RR will clear to raise and lower into position. The # MR98RR is for doorway widths of 23-3/4" to 21-1/4" and entry heights of 30" to 33".
    view full answer...

  • Can I Replace Current MORryde 3-step With a MORryde 4-step on 2018 Forest River Flagstaff 832OKBS
  • It is possible that you will be able to switch out your current MORryde 3-step RV steps to a MORryde 4-step, like the MORryde StepAbove RV Steps for 27-3/4" to 30-1/4" Wide Doorways - 4 Steps # MR28RR, but it will depend on a couple of measurements on your 2018 Forest River Flagstaff 832OKBS. Once you determine if you are able to go with the 4-step, it will not be hard to switch out the two steps. I have attached the installation instructions and the Qualification Guide for you to view. The...
    view full answer...

  • Determining Correct TorkLift GlowStep Revolution Scissor Steps For 2012 Rockwood 9312SS
  • I would be happy to help you figure out the correct TorkLift GlowStep Revolution Scissor Steps for your 2012 Rockwood 8312SS, but unfortunately I do not have a list that has the correct step for your trailer. To determine the correct steps you will need to take a few measurements, with the first being the dimensions of the mounting space for the steps under the door of your trailer. There are two different widths offered which are 25-1/2" wide like the # TLA8104, or 27-1/2" wide like...
    view full answer...

  • Will the Brophy Camper Scissor Steps # AS23 Fit My Vehicle?
  • I have a solution for you. Unfortunately, the Brophy Camper Scissor Steps - 3 Steps # AS23 will not work with the dimensions that you provided (thank you!) because you have an entry height of 36 inches from the ground to the entry way. The Brophy steps are only designed to fit steps that have entryway heights of 24-30 inches. With the information that you provided, the best solution would be the Brophy Camper Scissor Steps - 4 Steps # AS04. With these steps, they fit entryway heights...
    view full answer...

  • Recommended TorkLift Steps for Palomino SS1240 Pop Up Camper
  • I have a solution for you, but the TorkLift # TLA7843 require much more mounting space than you've got available on your 2020 Palomino SS1240. Because of the limited mounting space under your door, you'll need to use something similar to the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 4 Steps - 20" Wide # TLA7804-8000, which has a very narrow mounting bracket that is 1" tall x 20" long and will work well in the limited space you've got on your Palomino SS1240 camper. I...
    view full answer...

  • Is Item # TLA8003 Compatible With Bracket Dimensions Of 27-1/2 x 13-3/4 And Entry Height Of 29-1/2
  • Yes, TorkLift GlowStep Revolution Scissor Steps Item # TLA8003 is the correct steps for the measurements you provided to replace the steps on your 2016 Keystone Cougar Fifth Wheel. I do recommend, if you have pets, to add the SafeStep Vinyl Barrier Item # TLA7602. K9s have a hard time not looking through the steps as they walk up into the camper and get scared they are going to fall through. Adding the barrier provides a wall so they can see there is a back to it.
    view full answer...

  • Recommended Steps for Truck Bed Slide-in Camper with Bolts on Bottom of Threshold
  • The bolts you show will work with the TorkLift GlowStep Camper Scissor Steps - 2 Steps - Aluminum - 20" Wide - 375 lbs # TLA7802. The attachment bracket will work for this application. If you want to replace the pins with locks, you can use Pin Lock for TorkLift GlowStep Scissor Steps # TLA7509 to deter theft. The Brophy Camper Scissor Steps # SS02 are similar, but the mounting bracket would require you to do a custom 90 degree plate like you referenced since it doesn't have the pin...
    view full answer...

  • Torklift Glowsteps For Truck Campers Plus Add-On Step
  • If your door entry height (the distance from the ground to the threshold) is 37" and you bracket area (width) is 21-1/2" or greater then the TorkLift # TLA7804 is the correct fit. You can use the # TLA7801 Single Add-On Step to extend your reach.
    view full answer...

  • Are There Entry Door Quad Steps for Trailer with 30-1/2" Wide Bracket
  • The best option we offer to replace your quad steps would be to use ones that mount in the entry door like the MORryde StepAbove Fold-Down Steps. We don't have any entry steps that will fit the existing bracket width you listed so unless you wanted to modify the outriggers this would be your best option. In order to choose the correct steps you'll need to know your entry door width and threshold height. The part # MR28RR for example fits a a threshold height between 36-1/2" - 42" and an...
    view full answer...

  • Which Lippert Manual Pull-Out Step Is Correct for a 32 Inch Entry Height
  • The Lippert Manual Pull-Out Step for RVs part # LC432690 which is a triple step option would be best for an entry height of 32". The distance from the top of the mounting bracket to the bottom of the step is 25" therefore you will only have 7" from the ground to the first step which is perfect. Please note, you do need to verify the mounting bracket width is 27-1/2" which is pretty standard.
    view full answer...

  • Quick Release Hinge For Lippert Manual Fold Down Steps
  • I spoke with Lippert and they confirmed that SolidStep Manual Fold-Down Steps for 29" to 36" Wide RV Door Frames # LC791575 does not have a quick hinge function, just manual fold down and raise up. We do offer the Torklift GlowStep Revolution # TLA9005 that is a scissor style design made to fit and be used in small or tight paces. This product also extends to reveal a 5th step for use and fits doorways 28" wide. We do carry the detachable quick hinge kit for Morryde first generation...
    view full answer...

  • Installation Questions About Power Source for Kwikee Electric RV Step on Ambulance
  • I have a solution for you, but since you don't already have a step installed you'll need to use the Kwikee Electric RV Step Complete Assembly - Single - 28 Series - 23-5/8" Wide # LC3747453 instead of the # LC3747452 since it has all of the components needed for a new installation, where the # LC3747452 is designed to work as a replacement with existing components. With that said, you can use the Kwikee Electric RV Step Complete Assembly - Single - 28 Series - 23-5/8" Wide # LC3747453...
    view full answer...

  • Will The MORryde StepAbove RV Steps # MR48RR Be Compatible With A 1/4" Threshold To Door Gap
  • The MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps # MR48RR will work with your 26" door opening width and 36" entry height but the hinge of these steps does require a threshold height of 5/8" - 3/4". To allow room for the hinge plate, there must be a gap of at least 3/8" between the threshold and the bottom of the entry and screen doors. If the gap is too narrow, the doors may not close while the steps are down. Because of this I recommend going with the...
    view full answer...

  • What RV Steps Will be the Best Replacement for My Jay Flight Jayco 25BHS
  • The replacement steps I recommend for your Jayco Jay Flight 25BHS is the MORryde StepAbove RV Steps. I recommend the MORyde steps because the legs that extend individually on each side, providing maximum ground contact and stability. You will need to measure the entry height to your trailer to get the correct fit, since you already know the height we can use that to narrow down the possibilities. If your entry height is 30" - 33" you will need # MR68RR, if the entry height is 34"...
    view full answer...

  • Comparing Price of TorkLift Glow Step Revolution with SafeStep
  • The TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear - 4 Steps - 25-1/2" Base - 375 lbs # TLA8104 is their part number A8104. I don't know where you are seeing their pricing but I couldn't find it online to compare. We get our pricing directly from them, so we are offering the best price we can. I wonder if the difference is in shipping or if they are not including the Landing Gear, but can't confirm. As far as the SafeStep Vinyl Barrier for TorkLift GlowStep Scissor Steps...
    view full answer...

  • Clearance Needed To Fold Down MORryde StepAbove RV Steps In A Storage Lot
  • The MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways # MR98RR is going to be 36" in length from the hinge to the furthest part out. If you don't have enough clearance in your RV bay then you can detach these steps so you won't get locked out if you park in a tight storage lot where you can't fold the steps down. You'll just need to remove the pins from hinge plate to disconnect the steps so you can access your door.
    view full answer...

  • Can I Use the Brophy Scissor Step on a Class C RV
  • You could probably make the Brophy # SS02 work on your Class C as long as there is something secure to mount them to right below the coach's entry. These Brophy steps are typically used on truck bed campers that have limited space available for steps to be mounted, so if you've got something similar then you can make this work, but there are likely better solutions. Depending on the width of the door, the MORryde StepAbove RV Steps for 21-3/4" to 22-1/4" Wide Doorways - 2 Steps # MR86RR...
    view full answer...

  • Electric Coach Step To Replace Manual Steps on Motorhome
  • If your doorway is about 24" wide and you just need one power step to extend out, then the Kwikee # LC3747453 complete electric step assembly should be about right for you. I have provided two review videos for you. I have also included a link to this product page which has a chart of available doorway widths and entry heights for you to choose from if this one is not perfect. This includes everything you will need to complete your installation. However, if the installation of you...
    view full answer...

  • Picking Out Torklift 4 Step or 5 Step Glowstep Setup for 5th Wheel
  • The way to pick out the correct Torklift Glowstep is to go by the height from the threshold of the door down to the ground. Since you mentioned 3 feet the 4 step # TLA7844 is most likely what you need as it has a height range of between 31 and 42 inches. 3 feet is 36 inches. If you can get me an exact number though I can verify for sure what you'd want. The 5 step version part # TLA8005 has a height range of 39-1/2 to 52 inches.
    view full answer...

  • Does Brophy Scissor Step Mount Permanently to Rear of Camper
  • The Brophy Camper Scissor Steps # AS24 that you referenced is designed to get removed when travelling. So the bracket would install on the camper under the door permanently and then you'd mount the steps to them when you are parked as needed. To determine if you need this 4 step or the 3 step comes down to the height of your door from ground. The 4 step is good for if the entry height is between 31 and 39 inches whereas the 3 step # AS23 is for 24 to 30 inch entry heights.
    view full answer...

  • Replacement Linkage Arm Compatible with Kwikee 28 Series Step
  • For the Replacement Step Frame for Kwikee 28 Series Electric RV Step # LC3747457 you referenced, the linkage arm you want is found in the Motor Upgrade Kit for Kwikee Electric RV Steps # LC379145. This linkage arm is not available by itself.
    view full answer...

  • What Brophy Scissor Trailer Steps do You Recommend for My 40-1/2 Inch High Entryway?
  • For the best option for Brophy scissor steps, I recommend the Brophy Camper Scissor Steps - 5 Steps - Aluminum # AS25. These steps are made for entry heights that range from 40 - 48 inches tall and will work great with your current 40-1/2 inch tall height. However, another thing that you need to know is your entry way width. With the # AS25, this is made for entryways that will be able to accommodate a bracket width of 24" inches. We do offer steps with 18-1/4 inch wide brackets. That...
    view full answer...

  • How Much Doorway Height Does MORryde StepAbove RV Steps MR26RR Require
  • In order for the MORryde StepAbove # MR26RR to fold down you'd need to have between 25 and 29 inches from the threshold to the ground on your RV.
    view full answer...

  • How to Determine if MORryde StepAbove will fit 1998 Shasta TravelMaster
  • To determine if the MorRyde StepAbove part # MR86RR will fit your 1998 Shasta Travelmaster you have to check two things. You'll need the entry height to be between 25 and 29 inches and the doorway width to be between 21-3/4 and 22-1/4 inch.
    view full answer...

  • Replacements for Kwikee Steps on 1988 Motorhome
  • I was unable to find any reference to any of those models or part numbers, unfortunately. For a step of that age, there are very few - if any - replacement parts, and since your wiring is different, that leads me to believe that none of the replacement controllers will work for you. The only option we can offer is an all-new assembly with a motor, control, and switch, such as the Kwikee 40 Series Electric RV 2-Step - Motor, Control, Switch # LC3726892. The right one will depend on the...
    view full answer...

  • Folded Up Dimensions of Brophy Camper Scissor Steps AS24
  • I checked with Brophy and the folded dimensions of the scissor steps part # AS24 are 25" x 17" x 13".
    view full answer...

  • Which SolidStep Fold Down Step for Doorway that is 25-1/2 inches Wide
  • Since your step is 25-1/2 inches wide the correct triple SolidStep is the part # LC791572 according to our contacts at Lippert.
    view full answer...

  • Need Fold-In Style Steps for Trailer With Narrow Storage Space to Deploy
  • Yes the TorkLift GlowStep Revolution Uprising Steps, # TLA9004 has a booster/bonus step intended for use when needed. This is a three steep model intended for an entry height of 27-3/8" to 34-7/8" with 28" doorways. If you will need the 4th step regularly because of threshold height, it is suggest that you select the four step model, # TLA9005. This too will have that additional booster/bonus step as well as landing gear that creates a stable connection from the bottom step to the ground.
    view full answer...

  • Will the Lippert Steps # LC726895 Fit an Entry Level with a Height of 26 Inches?
  • I have a solution for you. Unfortunately, the Victory Step Manual Fold-Down Steps for RV and Toy Hauler Patios # LC726895 only fits on entry level heights of 30-45 inches tall. Unfortunately, we do not currently carry any bolt-on steps that fit stairs under 27-1/2 inches tall. With that being said, there are some stairs that do not bolt to your truck that will still get the job done. For this route, I recommend the Econo Porch Trailer Step w/ 2 Handrails and Landing # EHS-103-R. Since...
    view full answer...

  • 5th Wheel Step Replacement With 3 Steps
  • The correct fit for a manual fold down step with a 24" entry width and 34" entry height is the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps # MR48RR.
    view full answer...

  • Which MORryde StepAbove RV steps for 2016 Coachmen Apex Travel Trailer
  • To determine the best choice of MORryde StepAbove RV steps for your 2016 Coachmen Apex Travel Trailer you need to have the threshold height measurement and the doorway width. With your travel trailer arranged on a flat surface, deployed as you will normally when camping, measure from the doorway threshold on your camper to the ground. Then measure from the inside of your door flange to the inside of the door flange on the opposite side. Compare these measurements to the attached chart. For...
    view full answer...

  • SolidStep Manual Fold-Down Steps for 2018 Grand Design Reflection 311BHS
  • The how to measure height is rather straight forward and you do not need to be concerned about exact measurement. With your RV situated on a level setting and arranged the way you would typically have it when in use, measure the height from ground to the threshold. If your measurement is between 35" and 44" then you will want the four step model. For a four step Lippert SolidStep for your 2021 Grand Design Reflection 311BHS, I suggest the SolidStep Manual Fold-Down Steps for 29" to 36"...
    view full answer...

  • MORryde StepAbove RV Steps Modification or Replacement
  • After doing some research I was unable to find a way to safely modify your MORryde StepAbove RV Steps with Strut Assist - 23-3/4" to 24-1/4" Wide Doorways - 3 Steps # MR45RR. We do have the MORryde StepAbove RV Steps with Strut Assist - 23-3/4" to 24-1/4" Wide Doorways - 4 Steps # MR75RR which would change the steps to 8" apart. The thing you would want to watch with the 4 step would be ground clearance. The 3 step is a threshold-to-ground height between 31-1/2" and 37-1/2" and the 4 step...
    view full answer...

  • Will Lippert SolidStep on RV Cause Interference with Door Opening/Closing
  • When the SolidStep part # LC791573 is installed on your RV there would be slight reduction in clearance above the threshold like you can see in the picture I attached. If it's already tight there it would become tighter. You may have to adjust your door but in general this does not cause interference.
    view full answer...

  • SolidStep Manual Fold-Down Steps Leg Adjustment Height
  • The SolidStep Manual Fold-Down Steps for 25" to 28-7/8" RV Door Frames - Triple - Aluminum, # LC791572, has adjustable legs that adjust in 1" increments. When drawn fully in the feet can be pulled in approximately 1" from the bottom step. Please note the product review and installation videos that have been linked. A valuable addition to the SolidStep is the, Lippert Entry Assist Handrail for SolidStep, # LC799640. And the SolidStep Locking RV Storage Box - Powder Coated Steel -...
    view full answer...

  • Inner Door Clearance Required Lippert Solidstep Torklift GlowStep Uprising MorRyde StepAbove
  • The Lippert Solid Steps like part # LC791572 require 13 inches of inside clearance in the door. The MorRyde # MR48RR requires 8-9 inches according to MorRyde. And then the Torklift Glowstep Revolution # TLA9104 sits inward 12-1/2 inches. These are all dimensions I verified with the manufacturer. The feedback that we've gotten on all three of these is that they are all very solid when in use. These are the top of the line RV steps so that would be expected. So from that point of view...
    view full answer...

  • What Are the Dimensions of the Mounting Bracket for TorkLift Stow and Go Glow Steps
  • The bracket on the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375 lbs - Black Bracket # TLA7834 has holes spaced 9-3/4" apart horizontally and 2-1/2" vertically. The bolt holes are 3/8" in diameter.
    view full answer...

  • RV/Trailer Over Frame Step Replacement Recommendation
  • To solve your step issue I recommend the MORryde StepAbove Fold-Down Steps for 23-3/4" to 26-1/4" RV Door Frames - 8" Drop Item # MR98RR. This will bolt right onto the bottom portion of the door frame instead of the sides and has adjustable drop down legs. These steps adjust down to 23-3/4" so you'd have an inch to work with when placing these to make sure you have enough clearance with the cabinet door. I've attached a review video and a size chart for you as well.
    view full answer...

  • Recommended Replacement Steps For A Kwikee Part Number 903209000 Step Assembly
  • The Kwikee part number 903209000 comes up as a 32 Series step so the Kwikee Electric RV Step Complete Assembly - Double - 32 Series - 24" Wide # LC372261 would be the correct replacement and it comes with the whole setup to completely replace your old steps. You can reuse the old wiring if you want and plug these new steps in and save the wiring that comes with it for any future repair needed. The mounting bolts and washers do not come with the steps as you can just reuse your OEM bolts....
    view full answer...

  • Do MORryde Steps StepAbove Fold-Down Steps MR58RR Require Screen Door to be Removed
  • It is possible you will have to remove your screen door in order to use the MORryde StepAbove Fold-Down Steps for 21-3/4" to 22-1/4" RV Door Frames # MR58RR. The answer just depends on the gap you have between the bottom of your screen door and your threshold. As you can see by the cut out I added from MORryde, you will need a gap of at least 3/8" between the bottom of your door and threshold in order for the steps to work for you. I have added a link below to the installation instructions...
    view full answer...

  • Correct MORryde StepAbove Fold-Down Steps for a Coachmen Freedom Express Select Travel Trailer
  • The correct MORryde StepAbove Fold-Down Steps for a 24" wide doorway with 34" threshold is part # MR48RR. The width of the step is not the only reason you need to be within the specified range, the keeper which holds the steps inside the door must be taken into consideration as well which is why you cannot go with a narrower step like the one for 21-3/4" to 22-1/4" doorways.
    view full answer...

  • How To Determine The Correct RV Steps For A 2008 Tiffin Phaeton QSH
  • Manufacturers do not list the steps they use on their RV's so you'll have to measure the entry height (ground to the mounting bracket for the steps) and mounting bracket width to know what steps are the correct fit for your 2008 Tiffin Phaeton QSH. The Kwikee Electric RV Step Complete Assembly # LC3722862 are designed to fit an entry height of 14-1/4" and mounting bracket width of 32-3/8". This electric step assembly includes everything you need to automatically open and close the steps...
    view full answer...

  • Install Video Guide to Use for Install of Torklift GlowSteps
  • The Torklift Glow Steps part # TLA8003 install just like a standard set of RV steps. While I don't have a link to install instructions I can send you I did attach a link to an install video that will walk you through the process which will be much more helpful!
    view full answer...

  • Replacement Kwikee RV Steps with Switch
  • We have the Replacement Step, Motor, and Switch for Kwikee RV Electric Steps # LC3747451. This will be a simple kit that will come with a 4 terminal switch so that you can deploy and retract the steps when you want.
    view full answer...

  • What Comes with the Lippert Kwikee 26 Series Electric Step # LC3711361
  • The only things included with the Lippert Kwikee 26 Series Electric Step # LC3711361 are the step, the motor, the switch, and the adapter harness. This is the most bare kit that we carry as the other 26 series steps come with the control module as well. It actually wouldn't be a bad thing to have an extra switch and adapter harness in case something were to need replacing anyways.
    view full answer...

  • Width of Lippert LC733932 Solid Step RV Steps
  • The widest point of the Lippert # LC733932 Solid Step is 24 inches, which is the dimension from the outside of one stringer to the outside of the other. The latching mechanism that holds the steps folded upright into their storage position is width adjustable for doorways from 29-36 inches in width. The photo I provided shows a good view of the adjustable latching mechanism. I've linked to an installation/demonstration video for the Lippert Solid Steps.
    view full answer...

  • Lippert Solid Step for 24" Doorway
  • Since your narrowest entry width is 24", and your entry height is between 22" to 28", the best fitting Lippert Solid Step is part # LC713662. If your measurements are different you can pick the part number from the table below. Once you have these awesome steps you can get rid of the old rattlers and install a MORryde # MR43RR locking storage box. This box is great for tools, or roadside emergency supplies, or even black water hoses and parts that you do not want mixed in with other...
    view full answer...

  • Step Recommendation For 30" Door Width And 36" Entry Height
  • The MORryde StepAbove Fold-Down Steps for 27-3/4" to 30-1/4" RV Door Frames - 9" Drop Item # MR78RR will fit your 30" door width with 36" entry height. There isn't a strut assist for this size but you won't have any issues without it.
    view full answer...

  • Troubleshooting Kwikee Electric RV Steps That Only Retract 3/4 Of The Way
  • It sounds like something might be bent or damaged either on the steps, gearbox, or motor of your Kwikee Electric RV Step Complete Assembly 32 Series # LC372261. First remove the gearbox and motor and manually move the steps to see if they are the cause. If not then check the gear on the outside of the motor housing for any teeth that are damaged. If there is no damage then the culprit is most likely the internal gears in the gearbox. you can replace the gearbox with the Replacement Gear...
    view full answer...

  • Recommended Permanently Mounted 4 Step Scissor Steps For Camper
  • I may have another option but unfortunately the Brophy Camper Scissor Steps # SS04 you have were not designed to be permanately installed and will not work with the TorkLift GlowStep Stow N' Go Mounting Bracket # TLA7820 you mentioned. The Brophy # SS04 was designed to be removed when traveling, and only installed onto the camper when needed. The only option I can offer that would give you a permanently mounted option on your camper would be to use steps that were designed to be permanently...
    view full answer...

  • What Does Econo Porch Trailer Step # EHS-103-R-HR Weigh
  • The Econo Porch Trailer Step # EHS-103-R-HR that you referenced weighs 83 lbs. It has a weight capacity of 350 lbs. I attached a link to a review video for this for you to check out as well.
    view full answer...

  • Are the MORryde StepAbove RV Steps the Second Generation
  • The MORryde StepAbove RV Step part # MR65RR is the same as the STP-210 which is the newest generation. It is designed for a 31-1/2" - 37-1/2" entry height and 27-3/4" - 28-1/4" doorway width. It's a strut assisted model. If you have different measurements please let me know what those are so we can get the correct step or choose from the list below. Please note, the STP-3-30-07h is the older generation no longer made.
    view full answer...

  • Compatible MORryde StepAbove Steps With Strut Assist
  • The MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps Item # MR98RR is the correct fit for your 24-1/4" door frame width and 31" entry entry height. The steps that come with the strut assist require a minimum of 31/5" entry height. You could get the MORryde StepAbove RV Steps with Strut Assist - 23-3/4" to 24-1/4" Wide Doorways - 3 Steps Item # MR45RR and just not extend the legs all the way but you'll want to be careful not to trip because the first step will...
    view full answer...