Filter Questions and Answers:

reset filter

Expert Answers about Tow Bar Wiring


  • Recommended Wiring to Flat Tow 2020 Jeep Wrangler Behind Motorhome
  • To wire up your 2020 Jeep Wrangler so that it accepts the signal lights from your RV I highly recommend the Roadmaster Diode Flexo-Coil Wiring Kit # RM-15267. This will tap into the tail light circuits of the Jeep and provide you with a 6-Way to mount at the front, along with enough coiled wiring to go from there to the 7-Way on the motorhome. The included diodes prevent any potentially harmful feedback. I have attached an installation video on an earlier model Wrangler that you can...
    view full answer...

  • Roadmaster Universal Hy-Power Diode Wiring Kit to 6 Pole Round Connector on 2016 Kia Soul
  • First off, thank you for your recent purchases! It looks like you're getting your 2016 Kia Soul ready for flat towing, which is a rather large undertaking, but we're here to help make that as easy as possible. I'll start off by saying that after looking at your orders, there is at least 1 part you'll probably need if you don't already have it-but I will get to that shortly. The wiring diagram you're going to use for the Hy-Power Diode Kit # RM-154 depends on the wiring of both your RV...
    view full answer...

  • Wiring to Flat Tow a 2019 Jeep Wrangler Behind a Motorhome
  • Magnetic tow lights, like part # TL21RK, do their job just fine, are less expensive, and don't require much to setup so they're not a bad option by any means. The only real drawbacks to them is that you need to set them up or take them off each time you change from towing to driving the Jeep. They also have a chance of scratching the Jeep's paint since they're being attached to its surface each time. We often recommend them if you're not going to be towing the vehicle very often or if...
    view full answer...

  • Flat Tow Wiring Needed For 2020 Jeep Wrangler
  • The best option for flat tow wiring on the 2020 Jeep Wrangler is Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267. This will provide a 6-Way round harness on the front of the Jeep Wrangler that you can to your RV with the included flexible coiled cable. If you are planning on using a supplemental braking system, you will need a stop light switch kit part # RM-751490 which will alert you when the Wranger's brakes are being applied while flat towing. To complete...
    view full answer...

  • Can Standard Tow Bar Diode Kit fit 2020 Jeep Wrangler
  • For your 2020 Jeep Wrangler you can use a standard diode kit like the part # RM-152-98146-7. You do not need anything different for the lighting setup that you have.
    view full answer...

  • Plug and Play Wiring Harness for 2018 Ford F-150 To Tow Behind Coach
  • I have exactly what you are looking for in the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles part # HM56009 which is a fit for a 2018 Ford F-150 (All Models) and completely plug and play. In fact, the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles is the only plug and play flat-tow wiring harness on the market. Hopkins has been making wiring harnesses for a very long time so you can depend on them and this kit in particular. I have attached for you an install video...
    view full answer...

  • Heavy Duty Magnetic Towing Lights for Flatbed Trailer Towed by 2017 Ford F-350
  • It sounds like you're trying to add some lights to a flat bed trailer being towed by a 2017 Ford F-350. If your 2017 Ford F-350 has a 4 way round pin plug installed (or you're willing to do some wiring), you can use the Heavy Duty Magnetic Tow Lights # 337TL257M which comes with a 4 way round pin plug and socket to install on your vehicle. With that being said, I have a solution for you that won't require any additional wiring work. I recommend using the Heavy Duty Magnetic Tow Lights...
    view full answer...

  • How Many Hours Will the Custer Wireless LED Light Battery Last Between Charges
  • The Custer Wireless LED Tow Bar Light # LIW-LDTL has a 4-8 hours battery life before it would need to be charged, so it's not really ideal for the use that you're looking for. With that said, if you could figure out a way to keep it plugged in to a 12v power source inside the tow vehicle you could likely make this work as you're hoping. However, if you wanted a set of removable lights that work with a wireless signal, you may want to have a look at the Pilot Magnetic Tow Lights - Red...
    view full answer...

  • Can I Purchase Roadmaster Diode Kit Without The Coiled Adapter
  • Yes, if you do not need the 7-way to 6-way coiled adapter cord you can purchase Diode Kit and wiring part # RM-152 and vehicle side 6-way plug part # RM-910030-7. This 6-way plug is the same plug that comes with the kit # RM-15267. The Diode kit part # RM-152 comes with 4 diodes and 30 feet of 4-wire. It also comes with the connectors, zip ties, 1 ring terminal and plastic loom to wire the vehicle for lights while flat towing. I have attached an installation video of the diode kit in...
    view full answer...

  • How To Install Tow Bar Wiring On Vehicle With Separate Brake Signal And Turn Signals
  • When installing tow bar wiring on a vehicle with separate brake and turn signals that will be flat towed you would want to use a diode kit like the Demco 4-Diode Universal Towed Vehicle Wiring Kit w/ 7-Wire to 6-Wire Coiled Connector # DM9523010-54. When installed it will make your brake lights flash as the turn signals instead of your actual amber turn signals when being flat towed. If you wanted to keep the separate wiring for flat towing you would need the Vehicle to Vehicle Tail...
    view full answer...

  • Can Hopkins HM56202 be Wired into 6-Way Connector on Front of Towed Vehicle
  • Absolutely! We actually recommend doing this exact install a lot of the time. Using a 6-way, like part # PK12720 for an example, at the vehicle's front allows you to install additional wiring for a braking system or charge line but doing it this way makes it an easier install because the Hopkins # HM56202 is the easiest to install harness for your 2004 Jeep.
    view full answer...

  • Plug and Play Lights for Flat Towing 2019 Jeep Wrangler Unlimited
  • There is one plug and play option for lights when you are flat towing your 2019 Jeep Wrangler Unlimited, although it would use magnetic lights as opposed to the Jeep's lights. You would need the Pilot Magnetic Tow Lights - 4-Way Flat and 7-Way RV Connector - Wireless # NV-5164 which will plug into your Jeep's 4-way or 7-way to send signals to the mounted lights when you turn or brake. To use your Jeep's lights you'll need to splice into the wiring with the Roadmaster Diode 7-Wire to...
    view full answer...

  • Installation of Tow Ready TR118821 Flat Towing Wiring Harness on 2020 Jeep Gladiator
  • If the 4-pole/7-way on your Gladiator is already functional, you wouldn't need to add a 4 pole harness like the Curt # C56407. Adding the flat towing wiring harness like the # TR118821 wouldn't interfere with the factory trailer tow wiring. I've provided a wiring diagram showing how the # TR118821 installs as well as to a video showing a typical installation.
    view full answer...

  • Recommended Tow Bar Wiring Harness For 1997 Jeep TJ
  • Thanks for the pictures! The Blue Ox Tow Bar Wiring Kit # BLU79FR you were looking at has square connectors that will not plug into the connectors you have on your 1997 Jeep TJ. Since we do not offer a custom wiring kit that will plug into the connectors you have on your Jeep, I recommend the Roadmaster Universal Hy-Power Diode Wiring Kit # RM-154 which will splice into your factory harness and the included diodes will protect your factory wiring from feedback or damage from your...
    view full answer...

  • Wiring Options for Flat Towing a 2006 Mini Cooper
  • We actually have a decent amount of wiring kits that you can install on your 2006 Mini Cooper to flat tow it. If you plan on flat towing it frequently then installing a tail light wiring kit like the Roadmaster # RM-155 which uses a 4-Way to the motorhome or the Roadmaster # RM-152-LED-7 which uses a 7-Way to your motorhome is what I recommend using. After the initial installation all you'll have to do is plug in the wiring from the front of your Mini Cooper to the back of your motorhome. If...
    view full answer...

  • Diode Lighting Kit for 2019 Chevy Suburban & Does Battery Need to be Disconnected
  • Let's start with the lighting kit for your 2019 Chevy Suburban, and there are diode wiring kits available. The best option due to its reliability is going to be from Roadmaster, the Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Wire to 6-Wire Straight Cord # RM-152-98146-7. In regards to your battery, it does need to be disconnected in order to flat tow your Suburban, so what you will need is the Roadmaster Automatic Battery Disconnect with Switch # RM-766. What this...
    view full answer...

  • Availability of Plug-In Tow Bar Wiring Kit for 2020 Jeep Wrangler Unlimited
  • I do have a great lighting solution for you, however the Hopkins Custom Tail Light Wiring Kit # HM56200 that you referenced won't work on your 2020 Jeep Wrangler Unlimited. This custom harness is designed to fit earlier model Wranglers (up through the 2018 model year) and isn't compatible with the new generation. There isn't a similar custom plug-in harness available for your Jeep. If you'd rather not splice into the factory wiring on the vehicle (which I can certainly understand) another...
    view full answer...

  • Pulling Fuses to Flat Tow 2019 Chevy Sonic with Keyless Entry
  • Pulling those fuses are supposed to disconnect the power so that your battery doesn't drain so, naturally, your 2019 Chevy Sonic won't start without power. I recommend using the FuseMaster # RM76512 for the BCM1 and BCM2 fuses and then the FuseMaster # RM76511 for the F07 fuse. I'm not able to find the owner's manual online so you may need to use another # RM76511 for the DLIS 1 fuse as well. These FuseMaster units make it so that you just flip a switch to disconnect the fuses instead...
    view full answer...

  • Parts Needed To Flat-Tow a 2012 Fiat 500
  • It sounds like you are wanting to flat-tow a 2012 Fiat 500 behind a motorhome and if that's the case you'll need a few different components such as base plate kit, tow bar, safety cables, wiring harness, and braking system. I have attached each of these components for you below. For the wiring, I recommend the Roadmaster Diode 7-Wire to 4-Wire Flexo-Coil Wiring Kit part # RM-15247. It comes with everything you need and is our most popular option for this purpose. Roadmaster Crossbar-Style...
    view full answer...

  • Does 2020 Buick Envision Need Brake Light Relay and Which is Easier Blue Ox or Roadmaster Setup
  • Does our Allegro have trailer wiring already present at the rear of the vehicle? Like with a 7-way connector? If so the circuits are already combined regardless of what you see on the vehicle taillights. If you plan to use a diode kit or bulb and socket tow bar lighting solution you will need a brake light relay like # RM-88400 when using the brake system you mentioned so that the brake lights won't override the blinkers. It's a toss up on which is easier to use between the Roadmaster...
    view full answer...

  • Smart Diode Kit for a Ford Edge ST 2020?
  • If you are going to flat tow your Edge, you will need "smart diodes" as included in the Roadmaster # RO44FR Universal Kit. However, I would go ahead and get the Roadmaster # RM38FR kit that additionally includes the 7-way to 6-way cable and connectors that you will also need. Additionally, your Edge will drain its battery while being towed. I recommend the RM-766 battery disconnect unless you want to manually wrench the battery cables off every time that you unhitch and rehitch! Flat...
    view full answer...

  • Custom Tow Bar Wiring Harness for Flat Towing 2008 Jeep Commander Behind Motorhome
  • For your 2008 Jeep Commander, the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, part # HM56205 is what you are looking for. This harness easily plugs into your vehicle's existing wiring, located behind your Jeep's tail light assemblies. No cutting, tapping, or splicing is required. If your motorhome uses a standard 7-way connector, you can use coiled adapter # 787196 to connect to the 4-Way on # HM56205. With this harness hooked up for flat towing, your Jeep's lighting system...
    view full answer...

  • Does Brake Buddy Select Supplemental Braking System Drain Vehicle Battery
  • The Brake Buddy Select 3 part # HM39524 like you have plugs into a power outlet in the tow vehicle to power the brake setup. So what that means is that it's draining your vehicle battery as it's being used. Using a fuse bypass won't prevent this from happening. Only solution is a battery charge kit like the part # RM-156-25 like it sounds like you tried which will keep the battery topped off so that when it's being used it will hopefully recharge.
    view full answer...

  • Fuse Bypasses Needed to Flat Tow a 2016 Chevy Traverse
  • Both bypass switches are needed in order for you to flat tow your 2016 Chevrolet Traverse; the reason for that is because they are different types of fuses (at different locations, as you pointed out), so both switches are needed, the Roadmaster FuseMaster Fuse Bypass Switch - 50 Amp FMX Fuse # RM-76517 and Roadmaster FuseMaster Fuse Bypass Switch - (2) 20-Amp ATC/ATO Fuses # RM76514. I have added links to video installations of both bypasses being installed on a 2016 Traverse for you...
    view full answer...

  • How To Install a Flat-Tow Wiring Harness on a 2005 Jeep Wrangler with Trailer Wiring Harness
  • I do have options for you but it's largely going to depend on what trailer wiring harness you have installed on your 2005 Jeep Wrangler. The best and most simple solution for you would be to just use a set of magnetic tow lights, the MaxxTow Magnetic Tow Lights part # MT70097. However, we do have hardwire options for you as well. If you have a factory trailer wiring harness then you can use the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles part # HM56202 which is a plug and...
    view full answer...

  • Recommended Tow Bar Wiring and Safety Cables To Flat Tow 2017 GMC Canyon
  • Since you already have a tow bar, base plates, and a supplemental braking system for your 2017 GMC Canyon you are most of the way to a complete flat tow setup. Since you mentioned that you are using the Roadmaster Even Brake Portable Supplemental Braking System # RM-9400 you will also need the 12 Volt Outlet Kit # RM-9332, and Roadmaster Stop Light Switch Kit # RM-751472 for your Canyon. The last components you will need are the wiring, and safety cables you mentioned, and likely...
    view full answer...

  • 2021 Jeep Wrangler Sahara Unlimited Flat Tow Setup
  • Since you have the # DM9511008 tow bar, # DM9519336 base plates and # SM99242 Delta Force braking system covered, you'll only need a couple of other items to complete your flat towing setup. You'll need a wiring harness so the Jeep's taillights operate in conjunction with those of the motorhome, a stop lamp switch and possibly a high/low adapter if the installed height of the base plates has a height difference of greater than 3 inches compared to the motorhome's receiver height. For...
    view full answer...

  • Tail Light Kit For Kuat NV Base Bike Rack
  • The LED light kit # 98174LED and bracket # BK70BB is for a cargo carrier like this one # C18152. It will not attach to your Nv 2.0 # BA22B without rigging it up. Your best bet is to get something like the magnetic tow lights # PE26UR. These will connect to your 4 pole on your vehicle and will attach to your roof via magnets. This light kit won't interfere with your bike cover as the others may. Keeping the lights on your roof rather than your bike rack will be much more visible too.
    view full answer...

  • Using C56407 Trailer Wiring w/ TR118821 Taillight Diode System While Flat Towing 2019 Jeep Wrangler
  • In order to install the # TR118821, you will need to do a little splicing but the easiest and safest way to do that would be to tap into the wires on the Curt # C56407, the procedure for this is shown in the instructions for the # TR118821, which I've linked for you. Installing in this manner will not harm the trailer wiring harness in any way. I've linked to some videos that you might find helpful.
    view full answer...

  • Towed Vehicle Battery Charge Wire Kit for 2020 Jeep Cherokee
  • This had something to do with the electric steering assist and whatever it was that caused issue Jeep addressed. I do not know exactly what that fix was though. The Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Wire to 6-Wire Straight Cord, # RM-152-98146-7 is a confirmed fit to your 2020 Jeep Cherokee. Installation video is attached showing how to wire to a 2018 Jeep Cherokee. This will not cause a big battery draw but a battery charge kit is still recommended. ...
    view full answer...

  • Is The Mopar Flat-Tow Wiring Harness Needed for a 2018 Jeep Cherokee Trailhawk
  • In order to flat tow a 2018 Jeep Cherokee Trailhawk you will need a number of components which I have attached for you below along with some recommendations. In regards to the wiring, you will need both a tail light wiring kit like the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles part # HM56208 and a power steering pump wiring kit, the Flat Tow Performance Kit 68321424AB (Obtained Through Dealer) which I think is what you are referencing. The Flat Tow Performance Kit activates...
    view full answer...

  • Connecting Magnetic Tow Bar Lights With 4-Way to Motorhome With 7-Way
  • We have some options for you to connect magnetic tow bar lights to a motorhome connector (which should be a standard RV 7-way), though there isn't an adapter to go from the 4-round on the Heavy Duty Magnetic Tow Light Set # 337TL257M. While you could do some cutting and splicing to get it to work, the much easier option is to go with a magnetic light set with a 4-flat, the Roadmaster Standard Magnetic Tow Lights # RM-2120. There is an adapter that will go from a 4-flat to a 7-way,...
    view full answer...

  • Comparing the Roadmaster Combo Wiring Kit and Roadmaster Diode Flexo-Coil Kit
  • The RoadMaster Falcon 2 and Falcon All-Terrain Combo Towing Kit # RM-9243-1 was designed as a combo kit to be purchased along with Roadmaster Falcon Towbars like # RM-520. The Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 is a more 'universal' kit that focuses on giving you a 7-wire to 6-wire harness no matter what tow bar you have. The main difference is the Falcon Kit # RM-9243-1 has 8,000 lb capacity safety cables and extra tow bar accessories, while the Diode Kit...
    view full answer...

  • Difference Between RM-152-98146-7 and RM-154 Wiring Harnesses for Flat Towing 2020 Jeep Gladiator
  • The difference between the # RM-154 and the # RM-152-98146-7 is the trailer connector and the umbilical. The # RM-154 provides 4 circuits to the towed vehicle, right turn/brake lamp, left turn/brake lamp, running lamps and ground. The # RM-154 would provide a 4 pin trailer connector on the front of the towed vehicle and would require that the motorhome have a 4 pin trailer connector or an adapter like # 47345. The # RM-152-98146-7 kit also provides the 4 circuits mentioned above,...
    view full answer...

  • Replacing Incandescent with LED Bulbs in Roadmaster Tail Light Wiring On 2015 Jeep Grand Cherokee
  • You can switch over to LED lights by using the Roadmaster LED Bulbs # RM-152-2 . This will allow you to use the existing wires that you've already run with the Roadmaster Tail Light Wiring Kit # RM-155 and add LED tail lights in the place of the incandescent bulbs.
    view full answer...

  • No Splice Tail Light Wiring Harness Compatible with 2020 Ford F-150
  • Yes. The Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM56009 is confirmed to fit a 2020 Ford F-150. It simply plugs into your factory wiring connections at your tail lights and is run to the front of your vehicle for connection to your towing vehicle. You will however also need the # RM-88400 relay to prevent the towed vehicle's brake signal from overriding the turn signal from the RV when applying the brakes during a turn. I've attached a video of each installation...
    view full answer...

  • Wiring Third Brake Light for Truck Topper on 2012 GMC Sierra
  • Unfortunately, your photo didn't come through, but we get asked this question fairly often. There is a bundle of wires under the brake pedal of your 2012 GMC Sierra that will have an orange wire that should be used to power the third brake light of the camper shell. This orange wire is in the same bundle as the brake controller wires in the photo attached. If you want to capture the signal at your tail lights then you will use the Curt Vehicle to Vehicle Converter # C56196 to separate...
    view full answer...

  • Can 2013 Fiat 500 with Separate Taillights be Wired for Flat Towing with Diodes for Combined
  • Your situation is a very common one and the solution you proposed is the easiest and most popular solution. Like you mentioned you'd be wiring up the separate taillights to function like combined ones. You'd need a total of 4 diodes which we have that as a 4 pack with part # RM-794. I attached the correct diagram you'd need to use for your application.
    view full answer...

  • Recommended 10 Foot 7-way Trailer Connector Extension
  • TorkLift offers a 10 foot 7-way extension with a male 7-way plug on one end and a female 7-way socket on the other as part # TLW6510. I've linked to a product description video for the extension.
    view full answer...

  • RM-152 Diode Kit Compatibility With A 2021 Jeep Gladiator With LED Tail Lights
  • According to Roadmaster, if your 2021 Jeep Gladiator is equipped with ParkSense proximity sensors then you'll need the Roadmaster Universal Wiring Kit with Smart Diodes for Variable Voltage LED Tail Lights # RO44FR. If you do not have the ParkSense feature then you'll be fine with the # Roadmaster Universal Hy-Power Diode Wiring Kit # RM-152.
    view full answer...

  • Flat Tow and Trailer Tow Wiring Recommendations for a 2008 Subaru Impreza
  • The wiring kits used for flat towing are designed to receive signals while the wiring for trailer towing is designed for sending signals. The TowDaddy Custom Tail Light Wiring Kit # TD3003 that you referenced would get you halfway there but it actually fits a 2005 - 2010 Chevrolet Cobalt Sedan so you need to use different wiring. For your 2008 Subaru Impreza I recommend using the Tow Ready Tail Light Isolating Diode System # TR118821 for your flat tow wiring and then the Curt # C56111...
    view full answer...

  • Tow Bar Wiring For A 2021 Sahara Unlimited
  • The tow bar wiring for your 2021 Jeep Wrangler Unlimited will require Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit Item # RM-15267. If the brake lights were to override the turn signals you would use a relay however, I have found in most cases on the new Jeeps, they will fall asleep after about 15 minutes, Since you cannot tap into the factory brake wires on the Jeep, depending on the braking system you are using, it will require the Roadmaster Stop Light Switch Kit Item #...
    view full answer...

  • Tow Bar Wiring for 2016 Lincoln MKX
  • For your 2016 Lincoln MKX we don't have a custom tow bar wiring but we do have great options like the diode kit part # RM-15247 which will allow you to control the MKX taillights with your tow vehicle's taillights.
    view full answer...

  • How to Isolate Stop Light Signal for 3rd Brake Light on 2017 Ford Fusion
  • Thank you for all of the information about the wiring you are using for flat towing your 2017 Ford Fusion. If you are using the Curt 2-To-3-Wire Tail Light Converter # C56196 in conjunction with a wiring kit like the Tow Ready # TR118821 it should work properly to isolate the 3rd brake light signal but you need to make sure that you are connecting the right and left turn wires to something on the output side. A common misconception is that you can just cap those wires off but when I've...
    view full answer...

  • Replacement 4 Round Trailer Wiring Socket for Roadmaster 7-Wire to 4-Wire Flexo-Coil Kit
  • It sounds like you're looking for the Pollak Heavy-Duty, 4-Pole, Round Pin Trailer Wiring Socket - Metal - Vehicle End # PK11404, which can be used on the toad side to replace the socket that came with your Roadmaster Diode 7-Wire to 4-Wire Flexo-Coil Wiring Kit # RM-15247. If I'm misunderstanding you and you're in need of a different part, just let me know and I'm happy to help you locate the part you're seeking.
    view full answer...

  • Taillight Wiring Harness for Towing 2021 Ford F-150 Behind Motorhome
  • Although we have wiring harness options that will work for your truck, the Hopkins # HM56009 taillight harness for towed vehicles wouldn't work for your 2021 Ford F-150, it only fits up through the 2020 model year. I'd recommend using a diode kit like part # RM-15267, that would install as shown in the video I've linked for you. You'll also want to use a # RM-156-25 charge line kit to keep the truck's battery topped off while you're towing the vehicle. I've also linked to an install...
    view full answer...

  • Recommended Fuse Bypass Switch For Flat Towing A 2008 Honda CR-V
  • You'll only need a single fuse bypass switch like the Curt Fuse Bypass Switch for Towed Vehicles # C93HR you were looking at. You'll want to pull the ACC Radio fuse, which is fuse # 34 and the location can be seen in the attached picture. To flat tow your 2008 Honda CR-V you'll also need a tow bar, tow bar wiring kit, base plate, braking system, and safety cables. If you don't already have these items then I have the following recommendations for you below: Tow Bar: Roadmaster Falcon...
    view full answer...

  • Is Wiring Converter Needed for Flat Towing 2015 Mini Cooper
  • That's a good question but a wiring converter is not needed to install the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 on your 2015 Mini Cooper. Since it has separate lighting and your motorhome has combined lighting you can add Tail Light Converter # 118158 if you want to retain your Mini's separate turn and brake signals but it isn't a requirement. In regards to the airline you will run the vacuum line of the SMI Stay-IN-Play DUO Supplemental Braking System...
    view full answer...

  • Recommended Tow Bar Wiring Solution for 2017 Buick Enclave
  • It sounds like you're looking for a tow bar wiring kit for a 2017 Buick Enclave and while the Blue Ox Bulb and Socket kit # BX8869 would work just fine, it requires cutting into the back of the tail light housing on your vehicle and isn't really a convenient option if you're going to be installing the parts yourself. Instead I recommend using the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 which will splice into your vehicle wiring and comes with diodes to protect...
    view full answer...

  • Flat Tow 2021 Ford F-250 Super Duty
  • That is good that you already have the base plates and tow-bar for your 2021 Ford F-250 Super Duty, and the needed supplemental braking. That just leaves a few items such as the the wiring kit, I suggest the Demco 4-Diode Universal Towed Vehicle Wiring Kit, # DM9523010-54. For your supplemental braking, if you have the Demco SBS Air Force One Supplemental Braking System for Motor Homes with Air Brakes, # SM99243, then you all you need is the Second Vehicle Kit, # SM99209. You may...
    view full answer...

  • Troubleshooting Wiring on a Trailer with Separate Brake and Turn Signal Lights
  • There are two things that may help to solve your predicament. The easier one is the converter. The converter that you used, part # 118158, is not compatible with LED lights. So, even if the wires all lined up where they needed to go, it wouldn't have worked anyway. We do have one that is compatible with LEDs, though. It's the Curt Converter, part # C56196. I've linked to a video review of this converter for you to look at. As for the wiring, that's a little harder to figure out. From...
    view full answer...

  • Brake Light Relay to Allow Turn Signals of Flat Towed 2019 Wrangler to Work with Brakes Applied
  • What you need is the Roadmaster Brake-Lite Relay Kit for Towed Vehicles # RM-88400. This product was specifically designed for flat towed vehicles to prevent the brake pedal signal from overriding the turn signals like you are needing. Once installed your turn signals will work like they are supposed to even when the brakes are applied.
    view full answer...

  • Battery Life On the Custer Wireless LED Tow Bar Light
  • I contacted the manufacturer in regards to this question. Per the manufacturer the Custer Wireless LED Tow Bar Light - Weatherproof - Magnetic Base - 23" Long - 7-Way Round # LIW-LDTL-7B should be fine for several weeks after a full charge, if it is just sitting on the shelf. They recommend that if you use the light bar during the day, you should plug in the charger and get power to it during the night. That way it will always be ready to go. Once fully charged, the bar should last...
    view full answer...

  • Blue Ox Tow Bar Wiring Kit for 2021 Jeep Wrangler Unlimited
  • Yes, the Blue Ox Tow Bar Wiring Kit, # BLU79FR will work for your 2021 Jeep Wrangler Unlimited. This kit is a custom fit for the 2020 through current model Jeep Gladiator, and the 2018, through the current model Jeep Wranglers with, or without the tow package. But please note, Wrangler’s with tow packages have two identical connectors available on the driver’s side. Make sure to install the diode kit to the connector on the back side of the taillight option or the unit will not operate...
    view full answer...

  • Tow Bar Wiring Kit for 2021 Jeep Gladiator that is Flat Towed
  • For your 2021 Jeep Gladiator there aren't any custom fit tow bar wiring kits available so you'd have to go with a diode type kit like the part # RM-152-98146-7 which we've had the chance to install on a 2020 Jeep Gladiator and made an install video for which you can use as an install guide to walk you through the process.
    view full answer...

  • Fit of Blue Ox BLU79FR EZ Light Flat Towing Wiring Harness on 2021 Jeep Wrangler
  • According to Blue Ox, the # BLU79FR EZ Light wiring harness is a fit for all models of the 2021 Jeep Wrangler/Wrangler Unlimited.
    view full answer...

  • 2-To-3 Wire Adapter To Add Amber LED Turn Signal To Truck
  • I have another option but the Vehicle to Vehicle Tail Light Converter # 118158 you were looking at is not compatible with LED Lights. To convert the combined brake and turn signal wiring on your truck to separate brake and turn signal wiring I recommend the Curt 2-To-3-Wire Tail Light Converter # C56196 which we have found to work with LED lights, and will give you the dedicated turn signal wire you need to add an amber LED turn signal to your truck.
    view full answer...

  • Is There a Plug In Flat-Tow Wiring Harness for a 2021 Jeep Grand Cherokee
  • I have a few flat-tow wiring harness options for a 2021 Jeep Grand Cherokee. If you don't want to do any splicing whatsoever then I recommend the Custer Wireless LED Tow Bar Light part # LIW-LDTL-7B (see video below) as it mounts to the roof via a strong magnet and it is wireless. If you don't mind a bit of splicing then I recommend the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267 as it's an integrated package that uses the factory tail lights.
    view full answer...

  • Tow Bar Light that Can Fit Mini Cooper 2012 Convertible S that Bypasses Vehicle Wiring
  • It doesn't look like there is a flat metal surface that the # LIW-LDTL-7B could attach to at the rear of your 2012 Mini Cooper convertible so a different light kit like the # RM-2120 would be a much better option with the TLP01 helpers would probably work for you..
    view full answer...

  • What Fuses Need to be Pulled to Flat Tow 2019 Chevy Sonic with Remote Start
  • Your owners manual would be the correct guide for fuse pulling for your vehicle. We only really can give info we find in the manuals online which means that the manual is the final authority. So since your 2019 Chevy Sonic owners manual says you need to pull the fuses BCM1 and BCM2 that would be all that you'd need to pull. We used the FuseMaster bypass part # RM76511 on a 2019 Sonic just like yours which I have attached an install video for.
    view full answer...

  • What Dinghy Wiring do you Recommend for my 2019 Jeep Wrangler Moab with Led Lights
  • For your 2019 Jeep Wrangler Unlimited I recommend the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267. This is our go to wiring kit in tons of cases. It has the brackets, cable, diodes and everything you will need to get your lights working properly. I linked a video that my buddy Shane did on the wiring kit on a 2019 Jeep Wrangler Unlimited.
    view full answer...

  • Do Fuses Need to be Re-Installed at Each Stop When Flat Towing 2011 GMC Acadia
  • You will need to follow the instructions of the owner's manual to properly flat tow your 2011 GMC Acadia without damaging it. I took a look for myself and it does say to run it at the start of the day and at each RV fuel stop, and the fuses do need to be re-installed when you do this. Removing the fuses will ensure the battery does not drain and there is unfortunately no way around this. While you are welcome to try leaving the fuses in, there is a much better option. For your '11 Acadia...
    view full answer...

  • Pins of Curt Tow Bar Extension Cord w/ Socket
  • You link to # C59HR, the Curt Tow Bar Extension Cord w/ Socket. This connects the 7-way, blade-style connector from an RV to the 6-way round connector used for towed vehicles. This drops the black wire, the battery hot lead.
    view full answer...

  • Add Separate Trailer Turn Signal Lights
  • Please take a look at the Curt 2 to 3 Wire Tail Light Converter, # C56196. Pair this converter with an isolating diode kit, # 38955, to get the signal you are looking for. This is actually designed for use of flat towing a vehicle behind a motorhome, but the same results are achieved for what you are wanting, separate signal lights. It is rather straight forward, see the attached diagram. Remember that although wiring color code is identified, attach wires function to function even if...
    view full answer...

  • Flat Towing 2021 Ford F-150 Platinum
  • First, your owners manual forbids recreational towing of a 4X2 truck. If you have a 4X4 then follow the guidelines in the manual. You will need a flat tow wiring kit. You mentioned the # RM-154. I recommend the Roadmaster # RM-152-98146-7 Universal wiring kit which includes everything you need to connect your RV's tail, brake, and turn signal lights to your towed car. Diodes prevent feedback and wire your car to operate as a combined system. Includes a 7-way to 6-way straight adapter...
    view full answer...

  • Does Jeep Wrangler Battery Need Charging When Using Blue Ox Tow Bar Wiring Kit BLU79FR
  • Since it will be connected to your motorhome, you do not need any type of battery charger in your 2019 Jeep Wrangler Unlimited when using the wiring kit from Blue Ox: - Blue Ox Tow Bar Wiring Kit # BLU79FR
    view full answer...

  • Tow Bar Wiring Recommendation for 2020 Jeep Gladiator
  • For your 2020 Jeep Gladiator we have diode style tow bar wiring kits like the part # RM-15247 which would would great but we do not have any custom fit kit like you may be looking for. I did attach and install video for the # RM-15247 on a similar 2021 Gladiator for you to check out as well. This kit once installed will activate your Gladiator taillights while it's being flat towed and comes with a coiled wire to go between the tow vehicle and the towed vehicle.
    view full answer...

  • How Would 2001 TJ Wrangler Custer Wireless LED Tow Bar Light # LIW-LDTL Fit Wrangler
  • The Custer Wireless LED Tow Bar Light # LIW-LDTL that you referenced is designed to attach with the powerful magnets on the bottom of it either to the top of a vehicle or to the rear bumper. Looking at the rear of your 2001 Jeep TJ the best shot it's going to have at fitting properly is if you have a metal rear bumper you can set it on top of since the top is not metal. If you have other ideas let me know and maybe we can work out a better solution. I attached a review video for...
    view full answer...

  • Diode Tow Bar Wiring Kit Recommendation for 2020 Ram 1500
  • While you do have a separate taillight setup since your turn signals are on a different circuit from your stoplights you can still wire up your 2020 Ram 1500 for tow bar wiring like a combined circuit and it will work just fine and be totally legal. The red bulbs of your stoplights would just blink with the turn signals like a combined vehicle. The # RM-152-1676-7 that you referenced comes with everything you'd need so it would be the best overall setup and would work great too with the...
    view full answer...

  • Hopkins Wiring Kit to Flat Tow 2018 Jeep Wrangler
  • We do have a Hopkins wiring kit that will work with your 2018 Jeep Wrangler, but the wiring kit you mentioned is not available, like you said. What we know will work for your '18 Wrangler is the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM56200. We know this will work because of numerous customer reviews stating they have installed it, and we have also installed it on a 2018 Wrangler. I have added a link below to a video of that install for you to check out.
    view full answer...

  • How is the 7 Way Plug on the Custer Wireless LED Tow Bar Light Wired
  • In order to use the Custer Wireless LED Light # LIW-LDTL-7B you just need a standard 7 way connector. I've attached a photo of what a standard 7 way plug is going to be wired like, as well as one of our helpful articles on wiring a 7 way plug that you might want to refer to as well.
    view full answer...

  • Towing Lights that Bypass the Tow Vehicle's Wiring and Are NOT Magnetic
  • If you don't want to tap into your 2018 Jeep JL Wrangler's wiring to tow and your top does not have any metal for our magnetic lights, then we have one other option available for you. It's the Demco Tow Lights w/ Wiring Harness, part # DMKKLB. This light bar uses suction cup to attach to the roof or trunk and has a secondary connection by straps. This may work for your soft top, but I would suggest finding something with a suction cup on your roof first to test how well it sticks. You...
    view full answer...

  • Troubleshooting Installation of Roadmaster FuseMaster Bypass On 2019 Buick Envision
  • The Roadmaster FuseMaster Fuse Bypass Switch for Towed Vehicle - (2) 20-Amp ATM Mini-Fuses # RM76512 does not seem to be operating correctly. The manufacturer suggests to confirm the following when it fails to operate correctly: • …the pins are fully seated in the fuse socket and not touching each other; • …the wiring is properly connected to the back of the switch; and • …there is a properly-installed fuse in the FuseMaster harness and that it is not blown. Double check the installation...
    view full answer...

  • Can Brake Signal be Isolated from Hopkins Wiring for Flat Towing a 2019 Ford F-150
  • To isolate the brake signal from the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM56009 on your 2019 Ford F-150 you can just tie in the Pacer Performance 3rd Brake Light Logic Module # PP20-702. Attached is a photo of the installation instructions for you to check out.
    view full answer...

  • How To Use the Tow Ready Tail Light Isolating Diode System with 7-Way On Motorhome
  • If you wanted to use the Tow Ready Tail Light Isolating Diode System with 4-Pole Connector part # TR118821 with a 7-way trailer connector on the motorhome you'd need an adapter. If you wanted to also upgrade the umbilical that goes between the motorhome and toad you can use the Wesbar Coiled Adapter part # 787196 which also doubles as the adapter. The Mounting Bracket 4-Pole Flat part # 18144 can then be used to secure the 4-way on the Tow Ready harness.
    view full answer...

  • Recommended Tow Bar Wiring for 2021 Chevrolet Silverado 1500 Trail Boss
  • I recommend using the Roadmaster Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267, which comes with diodes to prevent backfeed and gives you a great solution to power the lights on your 2021 Chevy Silverado 1500 when towing behind your RV. You may also need the Roadmaster Brake Light Relay Kit # RM-88400 if you're using this in conjunction with a supplemental braking system. I've linked an installation video of this harness you can check out and use as a guide when...
    view full answer...

  • Is the E-Z Mount Tow Light Kit EZT20B Still Available
  • The E-Z Mount Tow Light Kit part EZT20B has been discontinued by the manufacturer and replaced with the magnetic base style, the Magnetic Towing Light Kit part # RM-2120. I did check all of our other options but none retain this same style of mounting. The list is attached below as well.
    view full answer...

  • How Does The Transmitter Get It's Power On The Custer 23" Wireless LED Light Bar
  • The transmitter for the Custer Wireless LED Tow Bar Light - Weatherproof - Magnetic Base - 23" Long - 7-Way Round Item # LIW-LDTL-7B gets it's power through the 7 Pole plug on the back of the RV. When the RV has power at the plug and the 7 pole is plugged in, the transmitter sends the signal to the light. The light has a 3AH battery which can be replaced. There is a panel on the bottom of the light to access the battery. A charge typically last about 6-8 hours. Keep in mind it is recommended...
    view full answer...

  • Flat Tow Wiring For 2017 GMC Terrain
  • I recommend Hopkins Custom Tail Light Wiring Kit for Towed Vehicles part # HM56108 which will plug into your vehicle's existing wiring behind the tail lights to activate the Terrains signaling functions with the motor homes. It does not require splicing like the other tow bar wiring options for your vehicle, I have attached an installation video for your reference. When you flat tow the GMC Terrain you will need to pull the ABS (fuse 16) if you have a 4 cylinder mode. you will need...
    view full answer...

  • 2021 Chevy Trailblazer LED diode wiring
  • Using the Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit for Variable Voltage LED Tail Lights Item # RM38FR you'll want to cut the diodes in just before the the twist-lock to the LED and another just before the incandescent bulb. The point of the diode is to stop power from reversing and damaging the wire behind it so being closer to the bulbs will help save wire in the event that there is a power surge. Hooking up diodes to your car will not cause the LED or signal lamp to act any...
    view full answer...

  • Do I Need LED Resistors When Installing the Roadmaster Hy-Power Diode Kit on 2021 Chevy Equinox
  • You shouldn't need to add resistors to your vehicle when using the Roadmaster Hy-Power Diode Kit # RM-154, however if your 2021 Chevy Equinox is the L Series (L, LS and LT) your vehicle has variable voltage tail lights and you would instead want to use the Roadmaster Universal Wiring Kit with Smart Diodes for Variable Voltage LED Tail Lights # RO44FR instead of the # RM-154. Your assumptions on the wiring of the vehicle bulb is also correct assuming that it's a single bulb running all...
    view full answer...

  • What Type of Diode Tow Bar Lighting Kit is Needed for 2018 Chevy Equinox
  • You are correct. Your 2018 Chevy Equinox does require the smart diode style of Roadmaster tow bar wiring part # RO94FR as the standard style in the # RM-15267 would not work. I attached an install video for this kit on a similar 2019 Chevy Equinox as yours for you to check out as well.
    view full answer...

  • Tow Bar Wiring Kit for 2019 Ford F-250 King Ranch Edition with LEDs Around Tail Lights
  • I did take a look at the tail lights that come on the Ford F-250 King Ranch edition and I can see what you're referring to with the LED lights. When installing the Roadmaster Tail Light Wiring Kit # RM-152-LED-7 you need enough space to drill a 1" diameter hole in each of the tail light housings. If you don't have the room inside the tail light housing because of additional LED lights around the lenses, you may need to switch from a bulb and socket kit to a diode kit like the # RM-15267....
    view full answer...

  • What Pound Rating are the Magnets of the Peterson Magnetic Tow Lights
  • The Magnetic Tow Lights - Red LEDs - 4-Way Flat Connectors - 20' Long Harness # PE26UR have a 35-40 lb pull force rating. The kit weighs less than 3 lbs so the magnets are very strong in comparison to the weight.
    view full answer...

  • Towed Vehicle Wiring Recommendation for my 2020 Jeep Gladiator
  • The Roadmaster Diode 7-Wire to 4-Wire Flexo-Coil Wiring Kit part # RM-15247 is a great option for the lighting only functions. We generally install the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267 however because it will allow you to trickle charge the battery and run your monitor wire through the coiled cable rather than needing a separate connection for it. For the charge line kit use the Roadmaster Battery Charge Line Kit for Towed Vehicles part # RM-156-25...
    view full answer...

  • Recommended Wiring Kit for Flat Towing a 2020 Jeep Wrangler
  • We do have a variety of wiring options to help you flat tow your 2020 Jeep Wrangler. I have attached our selection for you to filter through, but out of that selection I really like the Flexo-Coil Wiring Kit # RM-15267 because it is very reliable and it looks really clean when installed. If you'd like to get an idea of the installation process then I'm attaching a video of the Hy-Power Diode Wiring Kit # RM-154 on a 2020 Jeep Wrangler Unlimited for you to check out. The difference between...
    view full answer...

  • 7-Way RV to 7-Way Dinghy Tow Bar Wiring Extension
  • Thanks so much for the photos they were super helpful, and what you have is a 7-way on the RV and 7-way on your Jeep, and we do have one option for an extension cord that will work for you: - Curt Tow Bar Extension Cord w/ Socket - Coiled - 7-Way RV - 96" Cord # C39HR This cord will stretch up to 8 feet long which will easily span the width between your connectors. It does come with the additional 7-way socket for your Jeep which you don't need, but since 7-way to 7-way tow bar wiring...
    view full answer...

  • Correct Tail Light Harness to Flat Tow 2020 Ram 1500 4WD
  • The Tow Ready Tail Light Isolating Diode System with 4-Pole Connector # TR118821 (confirmed to fit your 2020 Ram 1500) ,draws the power from the RV in order to activate the turn signals, running lights and brake lights on your Ram, so the towed vehicle's battery being disconnected wouldn't pose a problem. That being said, based on the information under the "Recreational Towing" section in your owner's manual (pp. 423-427), your Ram's battery, does not need to be disconnected when flat...
    view full answer...

  • Can the Roadmaster Diode 7-Wire to 4-Wire Flexo-Coil Wiring Kit Be Purchased Without the Diodes
  • Yes, we do offer the Roadmaster Diode 7-Wire to 4-Wire Flexo-Coil Wiring Kit part # RM-15247 without the diodes and bonded four wire harness. In order to obtain this you'll need the RoadMaster 7-Wire to 4-Wire Flexo-Coil Kit part # RM-164-7.
    view full answer...

  • Troubleshooting Jeep Computer Issues with Diodes Installed on 2020 Jeep JL with LED Tail Lights
  • I reached out to my contact at Roadmaster and there are a few things to look out for when installing the Flexo-Coil Wiring Kit # RM-15267 on a 2020 Jeep Wrangler. First step would be to make sure that the vehicle fell asleep before you started unplugging things. If you didn't wait for it to fall asleep then that would be why you are seeing codes and you should be able to take your JL to your nearest Jeep dealer to clear the codes. The second thing to note is that you need to install...
    view full answer...

  • Replacement Coiled Section for Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
  • In order to replace the umbilical cord on the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267 you'll need the Roadmaster 7-Wire to 6-Wire Flexo-Coil Kit part # RM-146-7. It does however come with new mounting brackets as well.
    view full answer...

  • Is It Normal For Brake Light Of Custer Wireless LED Towbar Light LIW-LDTL-7B To Flash W/ Turn Signal
  • It sounds like you are saying that when the brakes are pressed in your tow vehicle, and the turn signal is on at the same time, that the brake light on the Custer Wireless LED Tow Bar Light - Weatherproof - Magnetic Base - 23" Long - 7-Way Round # LIW-LDTL-7B flashes with the turn signal. If that is the case, then everything is working correctly. On a 7-way connector like this light is powered by the brake signal and turn signal are powered by the same wire so their functions will be...
    view full answer...

  • How Long are the 4-Way Wiring Harnesses of Tow Ready Flat Tow Diode Kit # TR118821
  • There are two sections of 4-way wiring on the Tow Ready Tail Light Isolating Diode System with 4-Pole Connector # TR118821 that you referenced. There's a section that attaches to the converter boxes which measures 60 inches and there's a 25 feet long section that spans from the front of the towed vehicle to the wiring at the rear of the tow vehicle.
    view full answer...

  • Recommendation on Wiring a 2015 Ford F-150 for Flat Towing
  • On your 2015 Ford F-150, we have a couple options for you to choose when wiring your vehicle up for flat towing. The first option and most labor intensive would be to use the Roadmaster 7-Wire to 4-wire Flexo-Coil Kit # RM-15247. This kit includes the diodes and wire that will allow you to hard wire into your Ford's lighting wiring harness. You then would run the wiring to the front of the truck and install the 4- wire round plug. The 7-way to 4-way Flexo-Coil will connect your motor...
    view full answer...

  • What Lights Will Be Powered When Installing Tow Bar Wiring On 2020 Chevrolet Sonic
  • The Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit for Variable Voltage Incandescent Tail Lights # RM26FR you were looking at for your 2020 Chevrolet Sonic will power the tail lights when plugged in to your RV. You should have turn signals, brake lights, and tail lights that come on when you turn on the running lights of your RV. These functions will only happen on the tail lights, and will not light up the front turn signals. If you are missing any of these functions I recommend...
    view full answer...

  • Is Brake Lite Relay Needed When Installing Tow Bar Lighting in 2018 Jeep JK Wrangler
  • What braking system are you planning on using? If the system presses the brake pedal of the 2018 Jeep JK Wrangler like most do then yes you do need to use the # RM-88400. The reason for this is so that the stoplights of your Wrangler don't override the blinker circuits of the # RM-15267. I attached install videos for both kits in similar 2017 Jeep Wrangler Unlimiteds.
    view full answer...

  • Flat Towing Equipment Needed For A 2018 Jeep Grand Cherokee Limited
  • The Mopar kit #82216418AA was designed to maintain power to the electric steering pump to prevent the "Death Wobble" that owners were experiencing while towing their Jeeps. It should specifically say in your owner's manual if you need it but you can also contact you local Mopar dealer with all the specifics of your 2018 Jeep Grand Cherokee to confirm the necessity of this kit. The Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM56208 you ordered is not a compatible wiring...
    view full answer...

  • Do The Pilot Magnetic Tow Lights Illuminate as Tail Lights
  • The Pilot Magnetic Tow Lights part # NV-5164 take the place of your towed vehicle's tail-light, turn and stop light functions so they will be illuminated when the head lights are on. I have attached a review video for your reference.
    view full answer...

  • Correct Flat-Tow Diodes and Install for 2020 Chevy Equinox LT
  • The 2020 Chevrolet Equinox LT has variable voltage taillights so in order to use diodes you must go with the Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit part # RM26FR. I have attached an install video which shows the correct model with two taillight connectors as you have.
    view full answer...

  • Replacing Malfunctioning Flat Towing Wiring Harness on 2014 Jeep Wrangler
  • From what you describe, the the relays in the converter are going bad, and my contact at Hopkins agrees. The relays aren't readily accessible and aren't designed to be replaceable, so your best bet would be to replace the # HM56200 harness entirely. Or, you could go in a different direction with a more reliable hardwired system like the # RM-15267 from Roadmaster. Installation of this product would mean tapping into the wiring harnesses for the taillights of your Jeep, but this installation...
    view full answer...