1. RV & Camper
2. Camper Jacks
3. Tongue Jackx

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24"…

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if…

The only difference between these two 8,000 lb landing gear sets - other than price - is that one comes with the crank handle and the other does not come with the handle. - Comes With Crank Handle: Landing Gear Set w/ Handle #RVLG-8HDL - Comes…

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

Hello Brian; the 3/8" difference isn't enough to matter so you can use the #e89FV as a replacement. We do have the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb Round Trailer Axles #APUBR-8 for 3"…

Hey Tyler, so the difference is the amount of motors that each has. The Lippert PSX2 has two and the Lippert PSX1 like the part #LC298707 has a single motor. The foot print and mounting etc. is exact same so this will fit and work great in place of…

The only difference between the #RVLG-8HDL and the #RVLG-8000 is that the #RVLG-8HDL includes the manual crank handle, while the #RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended…

Hi Mike; the Ark Drop Down Corner RV Stabilizer Jacks #ARK77FR can be used in three different positions. At 30° and 60° they act as non-rated stabilizers. At 90° they have the 1,929 lb rating.

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice.…

Aside from the weight capacity of the jacks and their speed, they also have different mounting bracket locations. If you don't mind potentially having someone do some cutting and welding on your trailer then either one will work great…

Hey Tim, so the Ultra Fab Landing Gear part #UF17-943010 does use a more unusual weld stop dimension as it's 20-1/4 inches from outside to outside of the it's weld stops. So since it looks like you already ordered this you can…

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the…

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if…

The only difference between these two 8,000 lb landing gear sets - other than price - is that one comes with the crank handle and the other does not come with the handle. - Comes With Crank Handle: Landing Gear Set w/ Handle #RVLG-8HDL - Comes…

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

Hello Brian; the 3/8" difference isn't enough to matter so you can use the #e89FV as a replacement. We do have the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb Round Trailer Axles #APUBR-8 for…

Hey Tyler, so the difference is the amount of motors that each has. The Lippert PSX2 has two and the Lippert PSX1 like the part #LC298707 has a single motor. The foot print and mounting etc. is exact same so this will fit and work great in place of…

The only difference between the #RVLG-8HDL and the #RVLG-8000 is that the #RVLG-8HDL includes the manual crank handle, while the #RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches •…

Hi Mike; the Ark Drop Down Corner RV Stabilizer Jacks #ARK77FR can be used in three different positions. At 30° and 60° they act as non-rated stabilizers. At 90° they have the 1,929 lb rating.

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice.…

Aside from the weight capacity of the jacks and their speed, they also have different mounting bracket locations. If you don't mind potentially having someone do some cutting and welding on your trailer then either one will work…

Hey Tim, so the Ultra Fab Landing Gear part #UF17-943010 does use a more unusual weld stop dimension as it's 20-1/4 inches from outside to outside of the it's weld stops. So since it looks like you already ordered this…