1. Trailer Parts
2. Electric Winch
3. Car Trailer Winchx

Hey Eric, I recommend going with the Bulldog Winch Trailer Winch #BDW66FR. This winch has a static line load of 9,800 lbs, has a line speed of 29 FPM, and has a free spooling clutch with a 360 degree gearbox that can be rotated so you can reach the…

For a 12,000 lb. electric car trailer winch like the Bulldog Winch Trailer Winch part #BDW10040, I recommend a standard 12 volt lead acid battery rated up to at least 650 cold cranking amps (CCA). As long as the battery is rated up to 650 CCA then…

Hi Walter, For the Deka Battery Isolator #DW08770 you can go with 8 gauge wire. Deka actually makes an installation kit with this wire, the Deka Battery Isolator Installation Kit for Standard Alternators #DW08769.

I recommend the Bulldog Winch Winch Cover - Standard Truck Winches #BDW20046, It has a stretchy elastic bottom, and polyurethane interior coating. It is a quick and easy install or removal.

It is plastic. The ComeUp UW-5000si Trailer Winch item #CU645010 is a light duty winch so it's housing and base are made of plastic. I attached a picture below that will show you the base. I've also…

Since you've already got a 4 pole on your trailer, you'd just need to add a 7-way with #ETBC7 so that you can run a charge line using #10-1-1 from the accessory circuit to your battery. This circuit is…

A diode like the part #RM-690 is a great idea but the only issue is that is has a max load of 85 amps. A standard 5,000 lb winch, like the ComeUp DV-5000si #CU645010, will greatly exceed the 85 amp rating of the diode so it would be useless. What…

If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with the…

The Curt Front Hitch for the 2008 FJ Cruiser , item #31367, and the setup you are describing should work well, as long as the multi mount you are referring to is designed to fit into a 2 inch receiver. If you already have the winch but not the…

I have a solution for you to connect the Bulldog Winch Trailer Winch #BDW10039 to your vehicle's battery, but it will not work well for you to connect the winch to the vehicle's 7-way connector. The…

The LT3000 winch, #SW1130220, is a good choice for pulling a 2,350 pound vehicle onto your trailer. With a rolling load (your vehicle) on a 17 degree slope (typical range for a trailer ramp) the winch will have a 7,825 pound rolling load capacity.…

For your Aluma 6810 HBT trailer, I recommend the Erickson Horizontal E-Track - Zinc Coated Steel - 2,000 lbs - 5' Long - Qty 1 #E19148 along with the E-Track Backing Plate - Zinc Plated Steel - 6" Long…

Hey Eric, I recommend going with the Bulldog Winch Trailer Winch #BDW66FR. This winch has a static line load of 9,800 lbs, has a line speed of 29 FPM, and has a free spooling clutch with a 360 degree gearbox that can be rotated so you can reach the…

For a 12,000 lb. electric car trailer winch like the Bulldog Winch Trailer Winch part #BDW10040, I recommend a standard 12 volt lead acid battery rated up to at least 650 cold cranking amps (CCA). As long as the battery is rated up to 650 CCA then…

Hi Walter, For the Deka Battery Isolator #DW08770 you can go with 8 gauge wire. Deka actually makes an installation kit with this wire, the Deka Battery Isolator Installation Kit for Standard Alternators #DW08769.

I recommend the Bulldog Winch Winch Cover - Standard Truck Winches #BDW20046, It has a stretchy elastic bottom, and polyurethane interior coating. It is a quick and easy install or removal.

It is plastic. The ComeUp UW-5000si Trailer Winch item #CU645010 is a light duty winch so it's housing and base are made of plastic. I attached a picture below that will show you the base. I've…

Since you've already got a 4 pole on your trailer, you'd just need to add a 7-way with #ETBC7 so that you can run a charge line using #10-1-1 from the accessory circuit to your battery. This…

A diode like the part #RM-690 is a great idea but the only issue is that is has a max load of 85 amps. A standard 5,000 lb winch, like the ComeUp DV-5000si #CU645010, will greatly exceed the 85 amp rating of the diode so it would be useless. What…

If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with…

The Curt Front Hitch for the 2008 FJ Cruiser , item #31367, and the setup you are describing should work well, as long as the multi mount you are referring to is designed to fit into a 2 inch receiver. If you already have the winch but not the…

I have a solution for you to connect the Bulldog Winch Trailer Winch #BDW10039 to your vehicle's battery, but it will not work well for you to connect the winch to the vehicle's 7-way connector.…

The LT3000 winch, #SW1130220, is a good choice for pulling a 2,350 pound vehicle onto your trailer. With a rolling load (your vehicle) on a 17 degree slope (typical range for a trailer ramp) the winch will have a 7,825 pound rolling load capacity.…

For your Aluma 6810 HBT trailer, I recommend the Erickson Horizontal E-Track - Zinc Coated Steel - 2,000 lbs - 5' Long - Qty 1 #E19148 along with the E-Track Backing Plate - Zinc Plated Steel -…