Of all tie-down methods, chain and load binders have the most muscle to handle the toughest tie-down jobs. They're made for big, heavy loads. But they're also heavy to handle. If you must strap down heavy loads though, chains may be your best choice.To tighten those chains, you use a binder, a device that pulls slack out of the chain.
Applications of Tie-Down Chains
Chains are possibly the best choice for hauling heavy items. They're perfect for use with big trucks. They can secure heavy agricultural equipment and industrial machines like bobcats and skid loaders.
Pros of Chains and Binders:
Resist wear and breakage - durable, heavy duty, and strong
Cons of Chains and Binders:
Weigh more than straps
Could damage finished surfaces
Can rust
Capacity
Capacity is one of the most important considerations when you're choosing tie-down chains and binders. To get parts that have enough capacity to do the job, you need to know the weight of your cargo and the total number of chains you will use to tie it down.
The capacity of chain and binders is designated by safe working load limit (WLL), a measure of the amount of load the chain or binder can safely handle. The load being tied down must not exceed the combined WLL of all the chains being used. For example, if your cargo weighs 8,000 lbs and you will use 4 chains, each chain must have a WLL of at least 2,000 lbs. Four chains of 2,000 lbs WLL each will equal 8,000 lbs total, enough capacity to secure an 8,000 lb load. Each binder must also have a WLL of at least 2,000 lbs. A good rule to follow is to always use binders that have an equal or greater capacity than the chains they will tighten.
Chains are also rated by break strength, the amount of load that will cause the chain to fail. WLL is usually rated at 1/4 the break strength. WLL, rather than break strength, is used for calculating load limits because WLL is a realistic measure of a safe load limit for a chain.
At etrailer.com, we offer chain and binders with working load limits (WLL) from 4,500 lbs to 17,900 lbs.
Hooks
Tie-down chains and binders have hooks at the ends for attaching them to a trailer or tie-down point. You can anchor a chain by hooking it to a tie-down like a D-ring. Or you can wrap the chain around a strong, stationary part of your trailer, then slip the hook back over a link of the chain.
BindersA chain binder works by pulling slack out of a tie-down chain. The hooks on this device fit over links in a chain and then, when you pull or crank the handle, the binder pulls the links together thereby tightening the chain.
A standard chain binder operates with a lever that you push to tighten the chain. All of the tightening must happen with one push of the handle, which means that this type of binder often requires more effort and strength to operate than a ratcheting type requires. Because this type of binder lacks a ratcheting mechanism, it is usually less expensive.
A ratcheting chain binder uses a built-in ratchet to give you leverage when tightening chain. You push and pull the handle repeatedly until you get the chain tight. This type of binder doesn't require as much strength to operate as the non-ratcheting kind.
The Convert-A-Ball load binder combines the weight savings of a strap with the ability to tighten chain. It's lighter than an all steel binder, but it includes hooks at the ends of the straps to fit over chain links. For convenience, it tightens with a ratchet.
Chain and Binder Fit
Chain and binders must fit together as well as be matched in capacity. To fit together, the hooks of a binder must fit over the links of the chain. At etrailer.com, we list the sizes of chain that our binders will fit. This dimension is the diameter of the links in the chain.
Updated by: Jacob JUpdated on: 2/21/2024
I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…
The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. You will…
The red wire on a trailer brake controller like the Redarc Tow-Pro Liberty Brake Controller part #RED24FR when using the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers part #RED69FR will need to be attached to the cold side of…
I believe the connector you found is the connector you will use to plug in the wiring for your 7-way connector. There should be a wiring connector along the drivers side frame rail at rear of truck between the rear wheel and the rear of truck (see…
How many links get used when installing a weight distribution system really depends on the tongue weight of the trailer. Basically you set up a WD system so that the tow vehicle sits as level as possible when loaded. Changing the amount of links used…
We have one aluminum folding option for you and it is the 19x60 Curt Cargo Carrier for 2" Hitches - 500 lbs #C18100. This carrier is well made and will store close to your vehicle when not in use. We have another aluminum option also rated for…
The accent holes on the Americana Modular Wheel w/ -0.5 Offset - 17-1/2" x 6-3/4" Rim #AM22461 will measure 1.57". Just to cover all the bases, the pilot hole measures 4.76", the lug holes measure .66", and the valve stem…
Yes, you can upgrade from a 16" rim to a 17-1/2" rim if you have the clearance in your fenders and the right size studs. I recommend the Americana Modular Wheel w/ -0.5 Offset item #AM22461. This is a 17-1/2" x 6-3/4" rim with an…
It sounds like there is a short circuit that is overloading the running light circuit in the tow package wiring on your tow vehicle. The most likely culprit is a dirty or corroded trailer connector on the vehicle or trailer if not both. The first…
I was able to locate a wiring guide for jack motor switches such as your Atwood part and from these I linked a diagram for you. I also sent a link to a complete installation guide.
We do have an electric option available that may work for you. The HappiJac Electric Truck Camper Jack System #LC736514-ELKIT will have a higher capacity of 8,800 pounds, but does only have 34-1/2 inches of lift. This will also include the mounting…
I recommend the Buyers Products 4" Standard Bolt-On Trailer Winch #3371903020 for your trailer. This has the same mounting bracket as the Titan Chain Lashing Winch #TCLR965 you found. The Buyers winch has 2-1/2" of space between the frame…