How to Wire a 5 Way Trailer Plug (It's Easier Than You Think)

Although 5-way connectors are not as common as 4-ways and 7-ways, many trailers do use 5-way wiring harnesses. In particular, 5-way wiring harnesses are common on boat trailers with surge or hydraulic brakes.

Like 4-way harnesses, 5-ways provide the required running lights, turn signals, brake lights, and ground for the trailer. With a 5-way, there is also an additional pin that is typically used to power a reverse lockout function.

Trailer wiring can be one of the most intimidating components of your towing setup, but it doesn't have to be. Most of us aren't electricians, but that doesn't mean wiring a trailer is beyond us. We'll walk you through the trailer-wiring process for 5-way plugs below, so you can get your trailer up and running in no time.

What is the Color Code for 5-Way Trailer Wiring?

Before we get into the step-by-step walkthrough, we'll first go over the standard color code for 5-way wiring harnesses. This will make it easier when it comes time to make your wiring connections.

The color code for wiring harnesses can vary between manufacturers, but the general standard for 5-way plugs is as follows:

Green: Right turn/brake light
Yellow: Left turn/brake light
Brown: Tail/running lights
White: Ground wire
Blue: Reverse lockout

What Size Wire Gauge is Used for a 5-Way Wiring Harness?

The minimum suggested wire size for a 5-way trailer plug is 18 gauge for the turn, brake, running lights, and reverse lockout. The suggested minimum for the ground wire is 16 gauge.

NOTE: *Some manufacturers will use red/black wires instead of brown/green/yellow. For these harnesses, black is usually for the running lights, and red is for the turn signal and brake lights.

When making connections on your vehicle, check your vehicle's owner manual or use a circuit tester to confirm each wire's function prior to connecting. You can usually tap into your vehicle's wiring system with the circuit tester at the rear of the vehicle, behind the taillights. Activate each function (turn signal, brake lights, etc.) in turn and check for a corresponding signal from the circuit tester to make sure you have the right wire.

Wiring a Trailer with a 5-Way: Step by Step

Now that we have an idea what our wires do, let's get into the step-by-step process of wiring your trailer. We'll start with the trailer side first.

Trailer Side

Step 1: Prepare for Trailer Wiring Installation

Start by making sure you have everything you need to wire your trailer lights.

If you need to replace one or more of your lights, you can purchase trailer lights or use a complete trailer light kit, which will come with the necessary wiring included. Remove old lights before beginning the new installation.

If you don't need to replace your lights, you can simply use a 5-way harness.

Step 2: Connect Ground to Trailer Frame

Attach the white ground wire directly to a clean, bare section of the trailer frame using a self-tapping screw and ring terminal. For best performance, each component should have its own ground. For instance, each trailer light should be grounded separately along the trailer frame. This reduces the risk of a ground issue on one component impacting the whole wiring system. You can make these individual ground connections in step 4, when you connect the rest of your wires.

The trailer connector should extend 2-3 feet past the tongue. Make sure no paint, corrosion, or buildup is present at the ground location. (Clean if necessary.) If the trailer folds, make the ground connection behind the tongue, on the main body of the trailer frame.

NOTE: A bad ground is the most common source of issues when wiring a trailer. Check out our troubleshooting guide for help with common trailer wiring issues.

Wiring Diagram - Connecting Ground to Trailer Frame

Step 3: Run Wires Along Trailer Frame

Run the rest of the wires along the trailer frame to the taillights. Don't allow the wires to catch or chafe against any trailer components.

Feed your wires through the hollow trailer frame if possible for the best protection. You can also drill through the frame and use grommets if necessary. Alternatively, you can use wire clips or zip ties to secure loose wires along the frame.

Step 4: Make Trailer Connections

Once the wires have been run to their respective appropriate locations, it's time to make the connections to your trailer's lights.

Each light will have 3 wires: one that connects to the main harness's brown running light wire, one that connects to the turn/brake light wire (typically yellow or green), and a white ground that should be secured to the trailer frame.

Use a crimper to strip back the insulation on the wires. Then, use a butt connector and heat gun to connect the wires. Connect any additional ground wires from your lights.

HOW TO ATTACH WIRES (EXAMPLE):

Use a crimper to strip insulation from the end of each wire

Use butt connectors to connect your wires

Make your ground connection

Traditionally, the running light circuit (typically the brown wire) is carried on a single wire, so a jumper wire and some additional butt connectors are required to feed the running lights on the opposite side of the trailer.

As a simpler alternative, you can use a wishbone harness (also known as a Y-harness) such as this one. A wishbone harness is a 5-pole connector with 6 wires that effectively splits the running light circuit into two wires. One wire runs along the driver's side of the trailer, and the other runs along the passenger side. Wishbone harnesses make the wiring job easier and eliminate the need for splicing in a jumper wire.

5-Way Wiring Plug Diagram Traditional Color Code

5-Way Wiring Plug Diagram Wishbone Color Code

Vehicle Side

Now that our trailer is hooked up, it's time to wire our vehicle. Let's get started:

Step 1: Prepare for Vehicle Wiring Installation

If your vehicle already has a 5-way connector, then great! Simply plug the trailer-end connector into the vehicle-end connector, and you're ready to roll.

If your vehicle has a 4-way connector, the easiest way to add a 5-way is with an adapter.

If your vehicle lacks any kind of connector, you can install a 5-way connector.

Keep in mind that wiring is a custom component. There are several ways that a wiring harness can connect to your vehicle, and the type of connector you use depends on what is available for your vehicle year, make, and model. You can use our fitguide to find custom wiring for your vehicle.

Also take the time to confirm the function of your vehicle wires if you are splicing or clamping wires together. Check your vehicle's owner manual or use a circuit tester to confirm each wire's function prior to connecting. You can usually tap into your vehicle's wiring system with a circuit tester at the rear of the vehicle, behind the taillights. Activate each function (turn signal, brake lights, etc.) in turn and check for a corresponding signal from the circuit tester to make sure you have the right wire.

If you have a 4-way plug, add a 5-way with a 4-to-5-way adapter

Use a circuit tester to confirm wire function

Step 2: Connect Ground to Vehicle Frame

Just like we did on the trailer, we now have to connect the ground on the vehicle side. Attach the white ground wire to a clean, bare metal surface on the vehicle frame. Apply some dielectric grease like # 11755 to help prevent corrosion.

Step 3: Make Vehicle Connections

Your wiring harness will either plug into, clamp onto, or splice into your vehicle's existing lighting. The type of connection depends on what is available for your vehicle model. We'll go over each process in more detail below.

Some general notes and tips:

Some vehicles require you to route a power wire from the harness to the vehicle battery because the vehicle's electrical system cannot handle the amperage draw of the trailer lights. For a breakdown of how to route a power wire for a trailer wiring harness, click here.
If the vehicle connector is under the vehicle, use a mounting bracket to attach it to the vehicle. This will help prevent damage that may occur if the connector is left dangling.
Use a small amount of grease on all electrical connections—the plugs on your automobile and the 5-pole connector itself—to help prevent corrosion.

4-Way to 5-Way Adapters

An adapter will plug into your existing 4-way plug and provide an additional pin connection for your reverse lockout function. All you need to do is connect the additional wire to your vehicle's reverse light circuit. To do this, use a circuit tester to find the reverse light circuit, then use a quick-splice to connect this wire with your adapter's reverse lockout wire.

Watch video installation of 4-way to 5-way adapter installation

Plug-In Style

Some vehicle manufacturers essentially "pre-wire" your vehicle so that your wires are easily accessible for connection. T-connectors such as this one simply plug into your vehicle's existing wiring, no cutting or splicing required.

The plug-in location is typically near the taillights, underneath the vehicle, or behind the paneling in the back cargo area. You may have to remove your trim access cover, scuff panels, taillights, etc. in order to access the plug.

A T-connector connects to your vehicle's existing wiring via an OEM plug

Splice-In Style

Hardwire kits aren't quite as convenient as the other styles, but splicing into your vehicle wiring is actually less difficult (and scary) than it sounds.

After confirming your wire functions (using your owner's manual or circuit tester), connect your wires using one of three methods.

Soldering: This is the best way to connect wires. Simpy solder your wires together for the strongest, most reliable connection using a soldering gun. Use heat shrink tubing to protect the soldered connection.

Butt Connectors: If you aren't comfortable soldering wires, heat shrink butt connectors and a heat gun are the next best thing.

Quick Splices: The quickest, easiest way to connect wires is by using a quick splice. Quick splices force a metal piece into two separate wires, thus connecting the circuit. NOTE: Quick splices are the easiest—but least reliable—wire connection method.

Soldering Gun vs Butt Connector vs Quick Splice

When Finished

After wiring up your trailer and vehicle, it's a good idea to plug the two ends together and test the function of each wire. Make adjustments as needed. If everything lights up when it's supposed to, you're good to go!

Save or Share This Idea

Troubleshooting 4-Way and 5-Way Installations

Troubleshooting 4 and 5-Way Wiring Installations

Brake Controller Installation: Starting from Scratch

Routing the Power Wire for a Trailer Wiring Harness

Related Products

Shop Trailer Wiring Kits

Shop Wiring Adapters

Shop Circuit Testers

Steve J.

2/13/2023

It all worked for me! Thanks etrailer!

Explore Expert Info

on Wiring

Videos

for Wiring

Help Articles

for Wiring

Expert Answers

for Wiring

Best 2024 Chevrolet Silverado 1500 Towing Mirror Options

Best 2020 Toyota RAV4 Custom Fit Trailer Wirings

Installation: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2022 Toyota RAV4

Detailed Breakdown of the 40 Ft 5-Way Trailer Wiring Harness

The Low-Down on the InfiniteRule Trailer Coupler Lock

Installing the Curt Trailer Connector Adapter on your 2010 Acura MDX

Dexter DX7.5L A-60 Brake Actuator Review

What to Know About the Demco Hydraulic Brake Actuator-DM72VR

Choosing the Right Trailer Wiring

Feature Review LubriMatic LMX Industrial Strength Grease

Comprehensive Review: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers

Trailer Axle with Idler Hubs Spec Review

Trailer Wiring Diagrams

Wiring Trailer Lights with a 4-Way Plug (It&amp;#39;s Easier Than You Think)

Wiring Trailer Lights with a 4-Way Plug (It&#39;s Easier Than You Think)

Wiring Trailer Lights with a 7-Way Plug (It&#39;s Easier Than You Think)

Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)

Troubleshooting 4 and 5-Way Wiring Installations

Wiring Trailer Lights with a 6-Way Plug (It&#39;s Easier Than You Think)

Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)

Brake Controller 7- and 4-Way Installation Kit (ETBC7)

My Trailer Hitch Doesn't Fit

How to Bleed Your Trailer Surge Brakes

How to Adjust Your Trailer Brakes | The Ultimate Guide

Parts Needed to Add Electric Drum Brakes to a Trailer

How Much Does a Boat and Trailer Weigh?

Brake Controller Installation: Starting from Scratch

Wiring New 4-Way Connector on Trailer with 5 Wires

Going by the colors that you mentioned, it sounds like you have the typical set-up, green wire for right turn and brake, white wire for ground, yellow wire for left turn and brake, brown with green wire for right side running lights, and brown with…

view full answer...

Replacement Drum Brake Actuator for a 1995 4 Winns Model 3916 Trailer

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it&#39;s a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Where To Attach Blue Wire From 5 Wires on Trailer When Installing a 7-Way Connector

When wiring a 7-Way on your trailer with 5 wires, your green wire will be right turn/brake, the yellow wire will be left turn/brake, the brown wire will be the taillights, and the white wire will be the ground. You will want to find out if the blue…

view full answer...

Why Does 4-Pin Trailer Wiring Have 5 Wires

Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer…

view full answer...

4-Way Trailer Connector that has 5 Wires

Did you have a 4-pin connector that had 5 wires or was it a 5-pin connector? There is a big difference since you normally see a 5-pin connector on a boat trailer with the 5th pin used for an electric reverse lockout solenoid on a brake actuating…

view full answer...

Replacement Actuator for 1997 Four Winns Boat Trailer

I have some great replacement brake actuator options but that is the route you'll need to go as Atwood has been out of business for quite awhile so replacement parts are almost non existent. The best replacement option we offer is the Demco…

view full answer...

Parts Needed to Add 7-Way With Reverse Lockout Wire to 2021 Toyota Highlander XLE

The 7-Way RV Upgrade Kit #ETBC7L you were looking at is exactly what you need. The yellow wire will connect to the reverse light circuit on your 2021 Highlander XLE to power the reverse lockout solenoid on your brake actuator. This kit comes with…

view full answer...

Correct Bearing Buddies for 3.5K Trailer Hub and Drum Assembly 10 Diameter 5 on 4-1/2 Pre-Greased

The Trailer Hub and Drum Assembly part #AKHD-545-35-K can indeed be used with bearing buddies. These hubs will have a 1.98" hub bore diameter. In order to be sure there are no issues you'll want to be sure your hub bore diameter…

view full answer...

Replacement Equalizers and Wet Bolt Kit For a Tandem Axle Utility Trailer

Your tandem axle utility trailer will likely have an equalizer like the Curved Equalizer #TREQ104. These would have been held in place by 3" Shackle Bolts #166081 and Nylon Bushings #721590 and Shackle Links #LC122487 on the ends of the…

view full answer...

Will a 4000-LB Leaf Spring Fit on a 3500-LB Axle

Yes the 4,000-lb leaf spring is compatible with a 3,500-lb axle. There are a couple of important measurements. Spacing from eye to eye on the spring when unloaded with no weight on the axle. Inner eye diameter of the spring roll Spring width from…

view full answer...

Replacement for a Marine Master Boat Trailer Axle

In order to determine whether or not the Dexter Trailer Axle Beam with 4" Drop part #7685269 will be a good replacement for your Marine Master Boat Trailer Axle we would need to know the distance between the hub faces and spring centers on…

view full answer...

Can a 4-Way Trailer Connector be Plugged Into a 5-Way Vehicle End Trailer Connector

You will still be able to use the trailer with the 4-Way after installing the 4 to 5-Way adapter, #20036. First, you could just remove the adapter if you wanted to and then plug in the 4-Way like normal while stowing the adapter in the truck. The…

view full answer...