Part Numbers: TLD2101,TLD3109
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Average Customer Rating: 4.7 out of 5 stars (3125 Customer Reviews)
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there. Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.The drivers rear didn't get built correctly. the hole to put the tie done is missing. I had to drill a hole into the tie down so I could use it. Didn't notice the problem until I went to put the camper on my pickup. The other three are fine.
Forklift tie downs are manufactured to exact fit to existing manufactured frame rail holes. They lined up perfectly and after 6000 miles with camper on board have stayed secure. The only downside, (this is relative to when and ware you use you camper) they will corrode when driving through snow covered roads that have been treated with sand and/or salt. I use an oil based product to protect them corroding.
Easy install, very effective way to keep the camper were it's supposed to be. Just bought a new truck and ordered another set for it. As long as I have a bed mounted camper I will be using this tie down system.
On my 2017 Ram 2500 HD, were easier to install than the front ones because you don't have to put that bolt inside the frame. There is a standoff for a wire on each side that had to be removed, and will need to be secured with a cable tie or something (see attached picture). I had to remove my Trekstep from the driver's side, but I knew I would have to do that, so no big deal. Again, these are very sturdy, thus very heavy, and lighter aluminum tie downs might be considered to reduce weight.
Installation was easier than I expected. Fit my 2006 Dodge Ram 2500 perfectly.
This products is well made. The transaction was easy and the product arrived as expected. I've been using this product for a year and I have no complaints. It has held up well and does what it was designed to do.
The rear mount arrived this morning, and I immediately went to installation,,,the only thing that could have made things easier would be, if I had a more powerful air wrench to take the bolts out,,,lol.
Looks great! The quality of your product is impressive! And, to think the dealer wanted to charge me $200 to put them on.
I see these as a permanent attachments to my truck,
Great product and helps us a great deal. It fixes our camper tie down issue.
Love the TorkLift Tie-Downs! They are rugged and make loading and unloading much easier than my old basic Tie-Downs.
Seem like a solid well built product. A bit of a pain to install and the instructions could have been more clear and the manual put together better but overall satisfied.
Easy to install and super secure! Made my Lance 1020 feel like its part of my truck. Highly recommended for the juggernaut class truck campers. I’ll never go back to the stake pocket style or bed mount tie downs again.
Cameron
7/13/2022
1 year later, Im still very pleased. Ive gotten many positive comments from people that didnt know they existed and, after talking to me, plan on upgrading themselves.
TorkLift frame mounted tie downs, Torklift Fast Gun tie downs - AWESOME! Arrived Thursday as promised, picked the new Cirrus camper this morning. Installed the frame mounted tie downs - front and back - 1hour 45 minutes. Thank you etrailer!
The TorkLift frame mounted tiedowns for my truck bed camper mounted perfectly on my 2016 RAM 3500. They are holding my camper on very securely and will be tucked away nicely when I remove the camper for Winter. I plan on making a footstep to slide into the receivers then, so I have much easier access to my high truck bed when I use it to haul firewood. The only suggestion I have is that we cleaned up the punched out pin hole edges with a file, inside the receivers. The sharp ridges would have scratched the hold down assemblies a bit when inserted into the receivers. Maybe an opportunity for a manufacturing process improvement there?
Very stable easy to set up system
These camper tie downs are quality made. Very easy to install. Install time was under two hours. Shipping was fast as always.
These camper tie downs have been fantastic! They were easy to install and have made securing my camper a breeze. I really like how easy it is to pull the tie down portion of the brackets out when you aren't carrying the camper. In my opinion this is the only way to secure a truck camper.
Eric A.
7/2/2018
They were great. I ended up getting a different truck and bought another Torklift setup for the new truck. I couldn’t imagine using anything else for securing a truck camper.
Good service, haven't checked the packaging but everything looks OK from the outside.
Perfect fit, Talked to Will on the phone and h got me the right set-up for my 2015 Dodge Ram 3500. Thanks Will.
Easy to install whole job front and rear just under 3 hours
The only Truck Camper tie down devices that I will ever use.
They still work great after a year : )
Great camper mount. Easy install, fit and finish is awesome
These are very well made. They installed easily and fit perfectly. My only concern is that the tie down/turnbuckle attachment hole is slotted and looks potentially weak as a result. I don't know that it's weak, it just looks like making it without the slot would be a lot stronger.
Bruce
11/4/2020
After a year, these have worked out very well. The slotted holes I was concerned about have not been a problem.
Very pleased.easy install
I am really happy with tork lift rear tie downs on my 2004 3509 Dodge Ram dually. They have worked out good for me. I did have to move my rear camper tie downs so the tie down rods would clear the fenders but overall I am very happy with the tie downs.
Ask the Experts about this Camper Tie-Downs
Do you have a question about this Camper Tie-Downs?
TorkLift Accessories
Fit to this rack on your 2006 Dodge Ram Pickup
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Chris
9/3/2023
After two winters on the road, this product shows no sign of wear. Im happy with my purchase.