Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"

See what our Experts say about this CURT Trailer Hitch

• What Is the Towing Capacity Of a 2014 Ford F-150 SuperCrew 4x4 with 5.0 V8
  If the towing capacity of your 2014 Ford F-150 is greater than the weight of the Hyundai Sonata then yes, you can tow it. It looks like your towing capacity will be between 7,500 lbs to 9,300 lbs depending on wheelbase and axle ratio so that should be plenty for the Sonata but if you using a trailer you will need to factor that into the above as well. If you don't already have a trailer hitch for your F-150 then I recommend using the Curt Trailer Hitch Receiver part # 13368. If you can...
  view full answer...
• What Size Wrench/Socket for Nut of Hitch Ball # A-90
  The socket or wrench size that the hitch ball # A-90 needs is a 1-7/8 inch. As long as the tongue weight range of the weight distribution system you have encompasses the loaded tongue weight of your setup you should be good. Also, be sure to inflate the air bags before setting up the weight distribution.
  view full answer...
• Is Towing With A Hitch Better Than Towing With A Ball Mounted To Bumper
  Normally a bumper is rated at about 3500 lbs towing capacity. It is usually stamped somewhere on the bumper or possibly on a sticker. A frame mounted hitch is going to have more capacity for towing due to how it is installed. Also, most trailers will have a towing height of 17 to 19 inches, and a bumper on a truck will typically be around 20 inches. If the trailer is attached to the bumper and the nose of the trailer tongue is higher it can introduce sway when towing. It is better to...
  view full answer...
• What is Towing Capacity of 2018 Ford F-150 When Towed From Ball Hole in Rear Bumper
  I did some checking and it looks like the towing capacity of your 2018 Ford F-150 when using the rear bumper ball hole is 5,100 lbs. As long as your trailer weighs less than that you'd be fine.
  view full answer...
• Can 2019 Ford F-150 Tow Nissan Rogue on Trailer Using Bumper Hitch Ball
  I pulled up the online version of the owner's manual for your 2019 Ford F-150 and it lists a towing capacity of 5,000 pounds when using just the bumper (not a trailer hitch and ball mount). I do still recommend verifying this in your personal copy of the manual as well. The 2011 Nissan Rogue weighs around 3,200 to 3,500 pounds so you should be well under capacity even after factoring in the weight of the U-Haul trailer itself. If you still need a hitch ball for your bumper, such as the...
  view full answer...
• Can Hitch Extension Be Used To Tow Side by Side With Dodge Ram Carrying Truck Bed Camper?
  Assuming that your Dodge Ram has a 2" trailer hitch receiver you may be able to tow your side by side while your 8' long truck bed camper is installed. The longest extender we have for a standard 2" trailer hitch receiver is the Curt Extender for 2" Receivers # C45796 which is 18" long, has a tongue weight rating of 350lb, and has a trailer weight rating of 3500lbs. Keep in mind that the use a hitch adapter like the # C45796 reduces the capacities of your trailer hitch receiver by 50%,...
  view full answer...
• Can Trailer Hitches for 2009 Ford F-150 Be Used with Weight Distribution to Tow More than 6,000 lbs.
  All of the hitches available for the 2009 Ford F-150 are rated for 6,000 pounds gross trailer weight and 600 pounds tongue weight capacity. However, all of the available hitches (see link) are rated for use with weight distribution which will allow the hitch to tow 10,000 pounds (# 13368) to 12,000 pounds (# 75691) depending on the hitch. These are ratings for the hitch, but not the truck. You will need to check the owners manual to determine if a weight distribution system can be used...
  view full answer...
• Availability of a Front Mount Trailer Hitch for a Snowsport Snow Plow on a 2010 Ford F-150 4x4
  For the 2010 Ford F-150, we have two options for a front mount trailer hitch. First is the Curt Hitch, # C31068, specifically designed to fit 4 wheel drive models. If your truck has an air dam, it will need to be removed to install the hitch. I have included a link to the installation details below. The other available front mount hitch is designed to fit all models. It is Draw-Tite Hitch, # 65061. This hitch also requires modification to the air dam. A small section will be trimmed. There...
  view full answer...
• Trailer Hitches Available for 1988 Dodge Ram Pickup
  The hitch referenced in your question, Draw-Tite 2-inch model # 13368, does not fit your 1988 Dodge Ram pickup but we do have Draw-Tite and other brands of hitches that are confirmed to work on your 1988 Ram. The correct hitch to use will depend on your pickup's bumper type. Please refer to the linked article. If you click on the linked page you'll see all hitches for all versions of your truck and you'll want to select your bumper type using the drop-down menu tool. Select your bumper...
  view full answer...
• Hitch for 1999 Chevy S-10 LS 2WD Pickup
  For the 1999 Chevrolet S-10 LS 2WD pickup we offer hitch # 75085. My tech contact at Draw-Tite confirmed the fit of this 2-inch Class III hitch. The written instructions for this hitch and a helpful installation article are linked for you. All mounting hardware is included. If you also need a 4-pole trailer wiring harness you can use Tekonsha part # 118359. Installation of this harness is shown in the linked video. You may care to add a mounting bracket setup for the 4-pole connector using...
  view full answer...
• Recommended Wiring Harness for 2013 Ford F-150 with No Factory Towing Package
  On your 2013 Ford F-150 without any factory towing package you'll want to use the Curt Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 60" Wire Lead # C58044 to add a wiring harness on the rear of your vehicle. This does come with quick splice connectors to make the installation easier and will allow you to to tow a trailer that has a 4 way plug. If you need a 7 way plug, this 4 way provides you with the base functions needed for that; once the # C58044 is installed you'll want...
  view full answer...
• Recommended Hitch Receiver and Wiring Harness for 2018 Ford Escape SE
  I have a solution for you, but the Curt # 13368 is not the hitch you're looking for since it's designed to fit on the Ford F-150. Instead you're looking for the Curt # C13186 which is a confirmed fit on the 2018 Ford Escape SE and will provide you with a 2" receiver. The Curt hitches have a much more durable powder coating than the other hitches on the market, so it's built to withstand the rigors of the road much better and will help keep rust and corrosion away. If you're going to be...
  view full answer...
• Recommended Wheel Chair Carrier for a 2014 Ford F-150 SuperCrew Cab with a Curt Trailer Hitch
  Sounds like you have the Curt Class III Hitch # 13368, with a 600lb tongue weight. I have a solution for you, but it is not the Curt cargo carrier # C18152 you were looking at. I would instead recommend the Flint Hill Goods 30x50 Wheelchair Carrier with a 48-inch-long ramp # FHG77ZR. This rack will allow you to have a ramp to help load the 405lb wheelchair that you have. I have linked a video to this page of the carrier with ramp for you to check out. As long as you aren't going over...
  view full answer...
• Trailer Hitch and 4- to 7-Way Trailer Connector for a 2014 Ford F-150 with 3.5L V6 EcoBoost Engine
  The most popular trailer hitch for your 2014 Ford F-150 is Curt hitch # C14002. This hitch is probably going to be rated much higher than your truck can tow (up to 12,000 pounds using weight distribution) so if you are looking for something with a little lower capacity # 13368 would be a good option. It is rated for 600 pounds tongue weigh and 6,000 pounds gross trailer weight. When used with weight distribution it is rated for 1,000 pounds tongue weight and 10,000 pounds gross trailer...
  view full answer...
• How Will Available Curt Hitches for 2010 Ford F150 Install in Relation to the Rear Bumper
  Curt actually offers three different hitches for a 2010 F150 (see link). Part # 13368 is a Class III with a square tube crossbar and # 13371 is a Class III with a round tube crossbar. Both hitches have a 600 lb tongue weight, 6000 lb towing capacity. A class IV, part # C14002 with a 1000 lb tongue weight 10000 lb towing capacity is also available. You can see the installation instructions for all three hitches by clicking on the provided links. As you can see by the instructions, all...
  view full answer...
  
• Can Flat Bed Directly Tow with Bumper
  In your photo it looks like there could be a hitch ball hole in the cross brace on the back of your Chevy flatbed. If you can find a sticker or plate that indicates a tow rating, and a hitch ball of the appropriate rating and with the shank diameter to fit correctly, then you can tow. It also looks like there is not a lot of clearance for the trailer coupler, due to the vertical support near that hole. A coupler like # CT-5003-Z has a flat lip around the ball cup and this may contact...
  view full answer...
  
• Towing Set Up for a 2012 Ford F-150 Pulling a 2020 Coachmen 194BHS Apex Nano
  I would be happy to help you find a hitch for your 2012 Ford F-150. Since your 2020 Coachmen 194BHS Apex Nano weighs over 2,500 lbs you will also need a brake controller. Since your F-150 did not come with a hitch I recommend the Curt Trailer Hitch Receiver item # 13368. This hitch is custom fit and bolts directly to your trucks frame with included hardware. For your brake controller you will want the Tekonsha Prodigy P3 Trailer Brake Controller item # 90195. This is a proportional brake...
  view full answer...
• Setting Up 2001 Ford F150 to Tow 4500 lb Camper
  The towing capacity of your truck is going to depend on how the truck is equipped, such as the cab configuration and the rear end gear ratio. I can't provide you with a definite capacity without knowing the particulars of your vehicle, but I will say the the owner's manual will provide you with all the specifics according to how your vehicle is configured. The manual has a very comprehensive breakdown of how the way the vehicle is equipped affects the towing capacity. The lowest towing...
  view full answer...
• Receiver and Weight Distribution Hitch Recommendation for 1968 Ford F-250
  In order to use a weight distribution system you'll need to install a receiver hitch mounted directly to the frame of the vehicle. We don't offer any weight distribution systems that would allow you to utilize a bumper mounted trailer ball. If your heavy duty bumper is a standard or a step bumper, I'd recommend the Draw-Tite # 41947 which has a 1600 lb towing/16000 lb capacity if used with weight distribution. If you have a deep drop bumper, which is also called a cowboy bumper, use #...
  view full answer...

Do you have a question about this Trailer Hitch?