Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Get more clearance and a smoother ride when towing with Axle-Less trailer suspension. Built-in shock absorption limits rattle and bottoming out. E-Z Lube, 4" lift spindle raises deck height for additional clearance. Fits any trailer frame width.
Features:
Specs:
Note: This Axle-Less system requires crossbeam support. If your trailer frame doesn't have a crossmember in place, you can retrofit it with one, or you can add a support by running a piece of 2" x 2" steel tubing through the square holes cut into these units. You could also add a steel reinforcement bracket to the inside of the trailer frame.
Get more ground clearance and a more comfortable ride when you're towing with Timbren's Axle-Less trailer suspension. This suspension system provides great shock absorption to comfortably get you where you need to go and to protect your precious cargo as you travel - even on rough pavement. With 2 independently operating units, you'll get better handling when making tight turns. And because this system eliminates your axle and has lift spindles built in, you'll get maximum ground clearance.
There are many suspension options for your trailer or camper. So, what makes Timbren Axle-Less different?
Axle-Less systems are a definitive upgrade over traditional leaf springs, in part because they allow you to do away with your thru-axle, allowing for maximum clearance. As you've probably noticed, having a leaf spring suspension means that your axle will always hang at least a few inches below your trailer's frame, resulting in limited ground clearance. This may make it difficult to navigate rough roads.
In addition, while leaf springs do a great job of supporting an even load, they may cause your trailer to bounce and rattle when it's empty or to bottom out with a heavy load. And they don't offer any type of shock absorption for a smooth ride - unless you have upgrades built in. With Timbren's Axle-Less system, gone are the days of dealing with these annoyances - this suspension is designed for a quiet, balanced ride, whether your trailer's fully loaded or empty.
A torsion axle is a step up in terms of shock absorption, and it provides more clearance than a traditional, leaf spring suspension, but that crossbeam will still hang down some. And if your torsion axle gets damaged in any way, it can't be repaired - you'll have to replace the entire thing with a setup that matches your exact trailer frame width.
With the Axle-Less system from Timbren, you won't have a low-hanging axle beam to get in the way when you're driving on rough roads. The lift spindles on this setup will also raise your deck height, making navigating those rough roads way easier. And the rubber springs and independent operation both combine to absorb shock and deliver a smooth, easy ride. In addition, the Axle-Less system can be easily maintained over time, and it will fit any trailer frame width, so you don't have to worry about potentially ordering the wrong size like you might with other systems.
Another suspension upgrade on the market is Timbren's Silent Ride. This setup is a great option to reduce bounce and rattle because it has the same AEON rubber springs as the Axle-Less system. But the Silent Ride still requires an axle, so you won't get the same ground clearance or low deck height as you will with the Axle-Less suspension.
The Timbren Axle-Less suspension is designed with you in mind. All of the parts work together so you can tow your trailer comfortably - regardless of load size.
The first step in installing the Timbren Axle-Less suspension is to make sure that the mounting points for each unit are directly across from each other. The easiest way to measure this is to mark the desired mounting points on your trailer's frame. Then measure the distance between these points and the center of your trailer coupler. These measurements (A and B) need to be within 1/8" to keep your trailer frame square.
Once you have your mounting points lined up, you'll be ready to install the system. Drill 3 holes into your trailer frame at the desired mounting points. Then bolt each unit to the frame with Grade 8, 1/2" bolts (not included).
Because Timbren's Axle-Less system eliminates your trailer's thru-axle, you'll have to find another way to get the crossbeam support that keeps your trailer frame square. You have a few different options to do this depending on your application and how much fabricating you're comfortable doing.
If you're building a trailer, the best option is to begin building with the Timbren Axle-Less in mind and include a crossmember where you want to install the units on your frame. You can also retrofit an existing trailer with a crossmember.
If you don't have a crossmember where you want to install the Axle-Less system (and you don't want to add one), pick up a section of 2" x 2" steel tubing from a nearby weld shop. This tubing will serve as a support to keep your trailer square. It will hang only about an inch down from your trailer frame, providing more clearance than a thru-axle.
After you've mounted both of the units to your frame, you'll need to drill 3 holes into the steel tubing and into the built-in, square holes. Then, insert the tubing through the holes and secure it with 3 bolts (not included) on each side.
The last option is to fabricate a reinforcement bracket that can be attached to the inside of your trailer frame and to the Axle-Less suspension. It may be a little harder to fabricate a compatible bracket than to mount steel tubing, but you may get additional clearance with this method.
The following diagrams show measurements taken on the Timbren Axle-Less suspension system.
| A | B | C | D | E | F |
|---|---|---|---|---|---|
| 13" | 13-11/16" | 1" | 5" | 7-1/2" | 4-1/4" |
| G | H | I | J | K | L |
|---|---|---|---|---|---|
| 5-5/8" | 6" | 4-3/4" | 1-3/4" | 3-3/8" | 3-11/16" |
Alternate Instructions
Average Customer Rating: 4.6 out of 5 stars (313 Customer Reviews)
Get more clearance and a smoother ride when towing with Axle-Less trailer suspension. Built-in shock absorption limits rattle and bottoming out. E-Z Lube, 4" lift spindle raises deck height for additional clearance. Fits any trailer frame width.
The trailer rides great down the road and no more worries about saltwater and rusty leaf springs. Not a cheap option but I’m very happy with the setup. When installing, just be sure to measure accurately and have sharp drill bits. A drill press type of guide also helps ensure correct drilling angles. The first picture is of a mounting gusset a local welding shop made. One is needed for each side and necessary to provide needed mounting strength-at least on my trailer frame. Pics 2 and 3 show the mounted suspension on one side of the trailer. Pic 4 shows the suspension on one side of the trailer with the axle attached and a separately purchased disc brake assembly mounted on it. Finally, pic 5 shows a 2” box channel between both suspension assemblies. Independent suspensions would have been nice, but I wanted to ensure trailer rigidity was maintained. So, after one year, so far, so good. It’s all smooth sailing down the highway.
We use Timbren's ASR3500S06 on all of our XER trailers. We couldn't be happier. It is a well built suspension.
A must have suspension if you're building an off-road trailer!
David R.
9/27/2021
Its been a year and this suspension is still doing great!
Best suspension you can get for off-road trailers. We use this suspension on all of our VORSHEER XER trailers.
These are going on a single axle trailer. They appear to be heavy duty and well made. The shipping was quick.
Came late. Not e-trailers fault. Covid-19 and China's fault. They bolted right up on my trailer frame. Really like the way they make my tear drip trailer handle. No sway, no bouncing all over like it use to. Will always put these under any trailer I build from now on. E-trailer keep up the great work.
Only been driving around on the axle-less system for about a week now and it has far exceeded expectations. I get better gas mileage, my trailer now sits like it was intended to, my trailer doesn't bounce like it used to, I wouldn't trade this axle system for any other. Just wish I would have known which outboard assembly arm my trailer needed with the axle-less system before I placed my order. Still not a problem though, plan on using the wrong outboard arm to build a different trailer. So far, a great product!
works great, only had one discrepancy, on a long trip part of the rubber on one side of the trailer worked its way out, it was repaired and hasn't given us any other problems.
These are quality. Excellent ride height and clearance. Turns your ordinary trailer into a bulletproof beast.
You guys are awesome! Great how to vi deos.
Zac
12/8/2021
Great
Everything arrived in great shape and included easy to follow installation instructions.
The suspension I ordered is of high quality and I received it sooner than I expected , its good to do business with a company that produces its products so fast.
Everything was delivered ahead of schedule and met the expectations provided by the sales person.
Work great
Killer axles
Wow. Solid build.
Thank you Dena
Very smooth pull. I'm very impressed on how the trailer pulls. My traditional axle trailer seemed to bounce a lot on the highway which made a lot of noise, but with the Timbren Axle-less that I installed on a new trailer, the trailer is so smooth and way less noise.
Great product.
Do you have a question about this Trailer Axle?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Dale
4/22/2022
Actually over a year, and still working great.