Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This 1/2" diameter pin fits 1-1/4" square receiver hitches. Includes retaining clip. Zinc finish resists corrosion.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer.com. Today we're gonna take a look at this Curt half inch diameter hitch pin and clip for the 1 1/4 inch hitches. Now this hitch pin will secure your ball mount or other hitch mount accessory in your 1 1/4 inch trailer hitch receiver. The included clip right here is what'll insert into the hole at the end of the pin to hold the pin in place. So basically when you install this, you'll put your ball mount or hitch accessory in, run this through all the holes. When it comes out the other side, you'll just take your clip, slide that in, and that'll hold it into place.
And then when you're ready to move it, just take your clip out, slide your pin out, and then you can move your accessory or ball mount. This is a sturdy steel construction. Has a nice corrosion resistant zinc plated finish. Application, as we mentioned, fits 1 1/4 inch by 1 1/4 inch trailer hitch receivers. Pin diameter is a half an inch, and the usable length, which is gonna be measured from here to here on this pin is gonna be right at up two inches.
But that's gonna do it for a look at this Curt half inch diameter hitch pin and clip for 1 1/4 inch hitches.
Average Customer Rating: 4.8 out of 5 stars (733 Customer Reviews)
This 1/2" diameter pin fits 1-1/4" square receiver hitches. Includes retaining clip. Zinc finish resists corrosion.
works well, but with the particular hitch, the safety chain loops make getting the clip in the pin hole a little difficult. Slightly longer pin would be great
Bolted on easily, perfect fit. Low profile makes it barely visible. I use it for a bike track and I have full confidence in its support.
this was just what I needed to keep my bike rack from dragging over a hump where I park. works grate. and thank you.
Very nice Hitch Pin & Clip. Fits really well, I had some in the past that didn't.
Great product, tho directions called for 19mm socket (actually uses 18mm socket). Installed in my driveway using common tools, and drove the rear wheels up on some blocks of wood to get a couple extra inches of space to work. I loved the 'fishing wires' that came with to get the bolts and spacers through the holes - how clever!
Fit well, great product. Delivered as p romised.
It’s a great product, I highly recommend it, you won’t regret it
I always seem to miss place the pins so I got extra, the personal at rtrailer are great, Tammie you did a great job, that's why I keep coming back
Les C.
4/29/2023
Works great, Tammie did a great job,I will an have told my friends
Solid, Does it's job, and is cheap. What more could you want?
fast shipping great customer service
It's a pin. What can one say?
Quick. Fair Price. Excellent Communication. First, we ordered the hitch and had it installed. Then we needed the perfect fit for the task at hand: to pull a tank with gray water through a campground. Very specific. Just for our toad, a Smart car.
Etrailer.com has the perfect software to lead you to what you need for the perfect combination. Quick shipment, reasonably priced. Direct communication for every step in the process. All in all, exactly what you’d hope for during these extremely dysfunctional time.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
Brad H.
9/24/2018
Very happy with products all high quality feel confident using. Thanks
Rcvd my hitch today (one day earlier than predicted by etrailer when I ordered...well done!). Everything was received as expected/requested.
Crawled under the car and started installation immediately. Piece of cake really; although some people would struggle with the tight space, 13 year old car, and need to clean threads, and remove caulk/undercoat in order to achieve "hole alignment".
Hyundai also did a great job by having pre-threaded welded nuts in place.
So far.... a great product received in time to use this weekend (as was my plan).
Great job and great product by etrailer.
Also, the website was easy to use and the videos quite helpful.
I will be back!
Thank you,
2008 Hyundai Sonata
Frank
10/20/2022
Hitch etc is holding up fine. Routinely used to pull trailers up to 2000 lbs with a 2008 Hyundai Sonata. I avoid going over 55 mph, or sway is detectable.
They did the job!
Fits good and tight into the space available, and designed to take advantage of the strongest part of the unibody.
Pro tip #1: On Subaru installations calling for cutting out an opening, take the time to remove the bumper, allowing access to the unibody tunnel without hacking a hole into it, to insert the carriage bolts and reinforcement plates.
Pro tip #2: While you have access to the unibody tunnel, now is a great time to apply Fluid Film/Woolwax/B'laster Surface Shield to the interior of the unibody, bumper, and undercarriage, to make your automobile last much longer!
Arrived 1 day early. Will buy from etrailer agin
Excellent service, quick responses to questions and delivery
I got this a year ago to install on my tiny Honda Fit.It was easy to put together myself. I needed extra room to attend art fairs with all my product and displays. It works very well and so easy to take off and put it back on whenever I need to use it.
I ordered this part by accident I didn't notice it came with the hitch. I'm going to keep it. I have a bolt in one of my other vehicles.
like the stuff I;ve ordered so far!
It’s a hitch pin, it worked great. I don’t leave my hitch on 24/7. I would recommend a locking hitch pin if you plan on leaving your hitch on permanently. I only use mine a few times per year, so this one was perfect.
It's a hitch pin. What could go wrong.
Thanks for the fine service and quick delivery.
Nice fit. Shipped fast.
The most straight forward install ever. Excellent instructions, four bolts and your done. The only thing you really need is a torque wrench. Well designed product and no interference with stock exhaust on my 2011 VW GTI.
Do you have a question about this Hitch Pins and Clip?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
5/3/2024
We do have a hitch pin that would be longer, it is 3 inches with its usable length, part # ML1495DAT. And it also doubles as lock.