Self-Stripping Connector with Waterproof Sealant - 14-18 Gauge - White and Blue - Qty 1

See what our Experts say about this Spectro Wiring

• Quick Splice Connector Recommendation for Tapping into Stoplight Switch Circuit
  We don't have that info but I would almost guarantee it's a 16 gauge wire. The good news is that the part # SWC501746-1 is a quick splice that fits gauges between 14 and 18 so it should work the best.
  view full answer...
• Troubleshooting Trailer Brakes that Lock Up in Reverse with One Truck but Not Others
  Sounds like your trailer has surge brakes and the 7-way of your truck does not have the reverse light circuit complete which is preventing the reverse lockout from functioning properly. What you would need to do is run a wire from the center pin of the 7-way on your truck to the wire of your reverse lights that goes hot when you put the vehicle in reverse. Once you do that the reverse lockout solenoid will function properly. You'd want to use a quick splice like the part # SWC501746-1...
  view full answer...
• Quick Splice Connector Recommendation for Tapping Subaru Reverse Light Circuit for Backup Camera
  Sounds like you are looking for a quick splice connector. The one you'll want is the part # SWC501746-1. This fits gauges of 14-18 which is where your reverse light wiring will fall.
  view full answer...
• Orange Square Displaying on the Peak Performance Digital Wireless Backup Camera Part PKC0RB
  I called my contact at Peak Performance and they stated that the reason you are experiencing the orange square in the middle of the monitor on your Peak Performance Digital Wireless Backup Camera part PKC0RB is that there is a communication issue between the camera and monitor. What you will want to do is check the splice on the vehicle's reverse wire where the camera is attached in addition to the ground wire coming from the camera itself. I find it best to use something like part # SWC501746-1...
  view full answer...
  
• Installing the Power Wire of a Backup Camera to the Reverse Light Power on 2006 Honda Odyssey
  I looked up your specific vehicle and the green wire will be the positive wire and the black the ground. So you will connect your red wire on your backup camera to the green wire using a Quick Splice Wire Connector - Tan - 14-18 AWG (Qty 1) # 564.
  view full answer...
  
• Wiring Reverse Light Circuit to 7 Way Connector on 2016 GMC Terrain
  The center pin of a 7-way is typically the reverse light circuit. You'd need to tap into the reverse light circuit of your 2016 GMC Terrain to activate it. For a quick splice for 14-18 gauge wire you'd want # SWC501746-1 or for 10-12 gauge wire # 562. I'd recommend strongly that you run the 12 volt power wire back to the positive post of the battery and not to a 12 volt outlet to prevent shorting out that circuit.
  view full answer...
  
• Can a Third Brake Light Be Added to a Trailer
  To add a third brake light to a trailer is pretty simple, but does require an adapter to convert the signal. Because trailer tail light systems combine the stop lamp and turn signals for each side onto a single circuit, you will need to use a vehicle-to-vehicle tail light converter, part # 118158 to split the brake light circuit back out. The white wire on the input side of the converter would ground to the trailer frame, the green input wire would tap into the right turn circuit on...
  view full answer...
  
• How to Add a Third Brake Light to a Trailer
  To add a third brake light to a trailer is pretty simple, but does require an adapter to convert the signal. Because trailer tail light systems combine the stop lamp and turn signals for each side onto a single circuit, you will need to use a vehicle-to-vehicle tail light converter, part # 118158 to split the brake light circuit back out. The white wire on the input side of the converter would ground to the trailer frame, the green input wire would tap into the right turn circuit on...
  view full answer...
  
• Taillight Converter Recommendation for Adding Dedicated Stop and Turn Signals to Trailer
  You can use the turn signal converter part # 118158 to accomplish what you are trying to do but instead of cutting the trailer wiring to run to the input side of the wiring you'd need to use something like a quick splice part # SWC501746-1 so that you can get the signals you need ran to the converter without stopping the circuit from getting to the combined taillights you already have. Once you do this the output side of the converter box will have separate stop and turn signals available...
  view full answer...
• How to Install a European Trailer Connector on a 2013 Ford Explorer
  All of the trailer wiring harnesses we have for your 2013 Ford Explorer like the T-One Vehicle Wiring Harness part # 118540 will combine the separate turn and brake signal lighting on your Explorer to combined turn and brake signal lighting. In order to wire a european trailer connector onto your Explorer you would need to splice into each circuit on the vehicle with a quick splice connector like part # SWC501746-1 and then run the wire to respective terminal on the trailer connector.
  view full answer...
• Recommended Quick Splice Connector To Install Truck Bed Cargo Camera 3460010
  The Self-Stripping Connector with Waterproof Sealant part # SWC501746-1 can be used in place of the Quick Splice Wire Connector part 564 (No Longer Available) to install the Truck Bed Cargo Camera for 8" Factory Monitor part # 3460010 on your 2015 Chevrolet Silverado 2500. They are the same save for the water seal on the former.
  view full answer...
• Quick Splice Connector Needed for Stop Light Switch On Brake Controller for 2015 Toyota Sienna
  The Self-Stripping Connector part # SWC501746-1 can be purchased along with a brake controller of your choosing like the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 to splice into the stop light switch circuit on a 2015 Toyota Sienna. There are different styles of quick-splice connectors, the above will work just fine in place of the two part one that was shown in the video which we don't offer.
  view full answer...
• Trailer Left Turn Signal Does Not Work After Installing Hopkins Backup Camera on 2015 Ford F-150
  It sounds to me like something is not wired correctly inside of the connectors on backup camera # HM50002. Make sure that on both halves of the connectors the wires are attached to the pins and that there are no broken wires or bent pins in the connectors. The connectors are basically a pass-through device. The camera only needs the reverse light circuit to turn on (and the ground). So the only thing it could be is a broken connection from a wire or wires or bent/broken pins on the inside. Worse...
  view full answer...
• How To Install A Wiring Harness For Towing On A 1972 Volkswagen Bus Campmobile
  I do have a trailer wiring harness option for you to consider however, there are no t-connector wiring harnesses for your 1972 Volkswagen Bus Campmobile. In order to install a wiring harness on your vehicle for towing, you will need to hardwire in a harness such as the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector part # HM48035. The white wire will need to be grounded to the chassis, the brown wire will be spliced into the vehicle's tail lights, the yellow wire will need...
  view full answer...
• Installing the Hopkins Smart Hitch Backup Camera on a 2014 Nissan Frontier
  Without seeing the 2014 Nissan Frontier 7-Way disassembled I can't say for sure if there is a way to tee into the back of the connector. But even if you can't it is still easy enough to tap into the reverse light circuit. The reverse lights on a 7-Way will be the middle pin. Find the wire associated with the center pin in the connector that plugs into the back of the 7-Way. Then you would just need to use a quick splice connector such as # SWC501746-1 to tap in the backup camera wire to...
  view full answer...
  
• Where Is Reverse Light Typically Found for Activating Reverse Light Circuit on 7-Way
  To find the reverse circuit to use for the purple wire will require you to test the wiring to your reverse lights and then tap into it. We don't have specific instructions for your vehicle but if you check out the install video I attached for a 5-way adapter you can see how we found it on a similar vehicle. For a quick splice you would want the part # SWC501746-1.
  view full answer...
• Reverse Light Circuit on 2001 Ford F-150 7-Way Not Working to Power Hopkins Backup Camera
  If your reverse light circuit is not functioning on your 2001 Ford F-150 then it could be a blown or missing fuse in the tow package wiring. Under the hood in the power distribution box, check the fuse in location 6 and the relay in location 203. If either is blown or missing then it will need to be replaced. The other option is to run the wire associated with the center pin on the factory 7-Way to a reverse light wire behind one of the reverse lights and tap into it using a quick splice...
  view full answer...
• Converting 4-Way of 2001 Toyota Tundra to 5-Way to Tow Boat Trailer with Surge Brakes
  We have a solution to convert your 4-way to a 5-way so that your reverse lockout solenoid can activate but we don't have a plug and play style of adapter. Instead your best option is a 4-way to 5-way adapter part # 20036 which plugs into your current 4-way and then gives you an additional wire you'd run to the reverse light circuit of your truck. You can use a quick splice connector part # SWC501746-1 to tap into the circuit easily.
  view full answer...
• Can the Skull LED Lighted Trailer Hitch Cover be Used as a Tail Light
  The Skull LED Lighted Trailer Hitch Cover part # RP86523 as the name states is a lighted hitch cover, not a tail light assembly and will not work as such on your trailer. It is designed to be attached to a 1-1/4" or 2" trailer hitch receiver opening. The skull will have a low red illumination when the tail light are on and a high red illumination when the brake or turn light is activated. If you wanted to somehow mount this on your trailer then you would need to remove the 4-way trailer...
  view full answer...
• Recommended 7-Way Trailer Wiring Harness To Install On Trailer
  The Pollak 7-Pole, RV-Style Trailer Connector Socket w/ Wiring Harness and Mounting Bracket part # PK11898 is what I recommend that you use on the back of your trailer in order to install a 7-way as it comes with the trailer connector, wiring harness, mounting bracket, and the hardware to connect the mounting bracket. The wire connectors however will need to be swapped out with part # SWC501746-1. You are correct in that you will need to splice into the tail lights on your trailer in order...
  view full answer...
• What is Purpose of Fifth Circuit Of Trailer Wiring that Runs to Reverse Light Circuit
  The circuit for the trailer is what allows your trailer to be backed up without the brakes locking up. When that circuit is active it prevents the surge brake actuator from being able to build pressure and activate the brakes. You want to have it connected to your reverse light circuit on your truck. On the tailgate/rear door you'll need to look for a rubber grommet with that has wires in it. In that wiring bundle will be a circuit that carries the reverse light circuit. Tap into it with...
  view full answer...
• Parts Needed to Install 5-Way Trailer Wiring Harness on 2017 Kia Sorento
  What you'll need to do is install a 4-way on your 2017 Kia Sorento like the Tekonsha kit part # 118269 and then convert it to a 5-way with an adapter like the part # 20036. The adapter will need to have the blue wire ran to the reverse light circuit of your vehicle and tap into it with a quick splice like the part # SWC501746-1.
  view full answer...
• Activating Reverse Light Circuit of 7-Way Trailer Connector on 2017 Ford Edge SEL
  Not every vehicle will have the reverse light circuit available for the 7-way. Especially a smaller vehicle like your 2017 Ford Edge. Best option would be to run a wire from the reverse light pin of the 7-way (center pin) to the wire that powers the reverse lights of the vehicle. You'd want to use a quick splice connector like the part # SWC501746-1.
  view full answer...
• Parts Needed to Install 7-Way 1997 Jeep Wrangler for Towing Surge Brake Trailer with 7-Way
  First you need to start with a 4-way connector if you do not have one already on your 1997 Jeep Wrangler. For that you would want the part # 118356. Then to convert this to a 7-way to match your trailer you need the part # 37185. The purple wire of this kit needs to be connected to your reverse light circuit and you will be set. You would want to use a quick splice like part # SWC501746-1 to tap into the reverse light circuit.
  view full answer...