Clips and Clamps to Attach Wires and Wiring Harnesses to the Bottom of a Trailer Frame
Question:
Given that I have a trailer wiring harness, what are the ways to attach the wires to the underside of the trailer? Masking tape? Sodder? If sodder, can the sodder be placed directly on top of the wire as it lays on the metal frame?, Special connectors that attach to the frame what are they called? Thank you
asked by: Joel L
Expert Reply:
There are many ways you can secure wires to a trailer. I would not recommend the use of tape as it will wear out quickly when exposed to the elements. Soldering is also not recommended because it is a more permanent method and you may need to change wires or move them in the future the hot solder would also melt the coating on the wiring, causing a short. If you can find some large enough, wire ties could be a simple solution.
We have several clamps and clips that could work for this application. First is the Wire Frame Clip, # 464600. These clips are designed to secure one or more wires on your frame or panel surface. The height of the Wire Frame Clip is 1-1/2 inches, width is 1/2 inch, width for wire capacity is 3/8 inches, and the frame depth is 5/16 of an inch. It clips to the vehicle or trailer frame and secures with an edge that has two points like fangs.
Next we have the 1/2 inch Metal Loom Clamp, # A0500, and the smaller 1/4 inch # A0250. These clamps usually attached to the frame with self-tapping screws.
Products Referenced in This Question
- Electrical Tools
- Cable Management
- Wire Clips and Clamps
- 1/4 Inch Diameter
- Black
- Redline
more information >
Product Page this Question was Asked From
- Electrical Tools
- Cable Management
- Wire Clips and Clamps
- 1/2 Inch Diameter
- Black
- Redline
more information >
Continue Researching
- Shop: Wire Frame Clip
- Shop: Trailer Wiring
- Article: Trailer Lighting Requirements
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Shop: Trailer Hitch
- Shop: Fifth Wheel Hitch
- Video: Review of the Wire Frame Clip
- Shop: Metal Loom Clamp - 1/2"
- Shop: Metal Loom Clamp -1/4"
- Search Results: 1~1/16 inch lug nuts wheel covers hubcaps
- Video: The Low-Down on the PVC Grommet for 4" Round Recessed Trailer Tail Lights
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2"
- Shop: B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package - Dual Jaw - 25,000 lbs
- Shop: Gooseneck Hitch
- Shop: Bearing Kit, LM67048/25580 Bearings, GS-2125DL Seal
- Shop: Replacement Spindle Washer - Tang Type for E-Z Lube
- Q&A: Air Suspension Kit Recommendation for a 2002 Ford F-250 with B and W Turnover Ball Gooseneck Hitch
- Video: Detailed Breakdown of the Replacement Spindle Washer
- Q&A: Lug Nut Torque for a Trailer Wheel
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: Kenda Tires Manufacturer Spotlight
- Article: How to Accurately Measure Trailer Leaf Springs
- Search Results: license plate bracket
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
- Video: Review of Timken Trailer Bearings Races Seals Caps - Bearing And Race Kit - TMK54ZR
- Q&A: Is 14 Gauge Wire Too Small for Electric Trailer Brakes
- Article: Trailer Tire Sizing
- Article: Trailer Wiring Diagrams
- Video: How to Install the Curt Trailer Hitch Receiver on a 2007 Ford F-250 and F-350 Super Duty