Do Brake Lines Have to be Equal Length for them to Activate Brake Assemblies Equally

Question

Question:

The diagram for this hydraulic brake line kit shows the line from the actuator to the midpoint of the trailer but then a 19 inch line to one side and a 66 inch line to the other which tells me it has to be run down one side and the longer line takes it to the other side. Doesnt this configuration cause unequal braking pressure from one side to the other? Thank you

asked by: John S

0

Expert Reply:

Hydraulic pressure does not apply more braking to the closer brake lines than the ones further away. The pressure is equal across the entire system at all times so the braking would be equal regardless of one set of brake assemblies having shorter lines than the other.

expert reply by: Jameson C

0

Answer 1

Your trailer must have free backing brakes if you have never used the surge brake actuating coupler reverse lockout. If you did not have free backing brakes, your brakes would most likely brake even if they didn't lock up when you back up because…

view full answer...

Answer 2

The biggest difference between the servo styles that you'll notice is between free backing plates and the others. The free-backing plates will allow your trailer to back up without having the brakes lock up. With surge brakes typically when you…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Do Brake Lines Have to be Equal Length for them to Activate Brake Assemblies Equally

Product Page this Question was Asked From

Continue Researching