Is Sealant Required to Install the Camco RV Drain Valve w Flange # CAM22223

Question

Question:

what type of sealent do I use to replace valve on my rv.

asked by: Mikr

0

Expert Reply:

When installing the Camco RV Drain Valve w Flange # CAM22223 you would not need to use sealant as long as you use the proper size tubing. Either 1/2 inch or 3/8 inch tubing.

expert reply by: Jameson C

0

Answer 1

There isn't a difference in handling between bias and radial trailer tires; bias tires are designed more for hauling heavier loads and won't flex as much on the side walls. The downside is they'll run a bit hotter than radial tires that…

view full answer...

Answer 2

There is a drain valve for you that will work; the Camco RV Drain Valve for 1/2" or 3/8" Diameter Drain Hose - Male NPT Thread #CAM22243 has, as the title suggests, a 3/8" diameter male NPT thread so it will work for you.

view full answer...

Answer 3

The Camco RV Drain Valve #CAM22243 is a 2-piece item. If you refer to the linked photo you will see it is composed of a threaded base part that will fit both 1/2-inch and 3/8-inch RV drain hoses and a handle part that inserts into the hollow cylinder…

view full answer...

Answer 4

Since you have already determined that it is a ground issue (which is almost always the problem) I would try sanding down the area you are installing the clearance light on. A good ground will have a solid connection to a clean, bare metal surface.…

view full answer...

Answer 5

The Camco RV Drain Valve #CAM22243 is threaded so it will not plug in, you will need to screw it in. The valve has 1/2 inch and 3/8 inch diameter male NPT threads and is for use with vinyl tubing. I've added a link to a video review for you to…

view full answer...

Answer 6

To install the #3802348 , the blue wire will connect to the blue wire that's on your battery box and the black wire will connect to the trailer brake wire from your trailer connector to the brakes. Breakaway switches are just there to create an…

view full answer...

Answer 7

The ground pin of a trailer side 7-way connector like the 7-Way Molded Trailer Wire Connector, 4' Long #H20043 you were looking at is the 5 o'clock position as shown in the included picture. For the vehicle side of the 7-way connector it…

view full answer...

Answer 8

We don't have the specific pin, but I have a solution for you. Since Breakaway Switches are universal, I recommend you replace the entire switch with part #3802348 to go with your ESCO breakaway systems.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Is Sealant Required to Install the Camco RV Drain Valve w Flange # CAM22223

Product Page this Question was Asked From

Continue Researching