Parts Needed to Install Trailer Brakes on 2015 Livin Lite Quicksilver 10.0 Tent Trailer
Question:
Somewhere on your site I think I saw someone get information about adding electric brakes to a Livin Lite quicksilver tent trailer. I am interested in adding brakes to my 2015 quicksilver 10.0 trailer. Thankyou.
asked by: Forrest L
Helpful Expert Reply:
I can certainly help you determine what parts you need to add electric brakes to your 2015 Quicksilver 10.0 tent trailer.
Based on my research, it looks like your trailer has a 2,000 pound axle. If that is the case you can use the following part numbers:
Brake Mounting Flange - # 4-34
Brake Assemblies - # AKEBRK-2L left-hand side # AKEBRK-2R right-hand side
Hub and Drums - # AKHD-545-2-EZ-2K for 5 on 4-1/2 inch wheel bolt pattern or # 8-173-16UC3 for 4 on 4 inch
Breakaway Kit - # PS50-85-320
Before ordering any components, I strongly recommend you double check your axle's capacity. If it is not a 2,000 or 2,200 pound axle, let me know and I will be happy to recommend the correct parts for you. You can also check and see if your trailer axle already has a brake mounting flange.
For trailer wiring, I recommend using the Trailer Wiring 7-Way Upgrade Kit # HS381-9000. This will provide you with a 7-way trailer connector on your trailer so that the brakes can get signal from the vehicle. To run the signal wire back to the brakes, you will want # 12-2-1, which is sold by the foot. You will also need Butt Connectors # DW05745-5. You will want to run the # 12-2-1 wire to the brake assemblies, and either wire on the brakes can be used for signal or ground.
The trailer brake controller I recommend for your 2015 Honda CR-V is the Tekonsha Prodigy P3 Trailer Brake Controller # 90195. The Prodigy P3 is our most popular brake controller, and it has all the best features. It has a customizable LCD display that provides easy-to-read troubleshooting. The P3 has integrated safeguards that protect your vehicle, trailer, and the controller. I have attached a review video of this controller for you.
To install the brake controller, you will first need to have a 4-pole harness, like # 118561, already installed. Then you will want to use the Universal Installation Kit for Trailer Brake Controllers # ETBC7. This kit will provide you with a 7-way connector at the rear of your CR-V and all of the wiring and hardware needed to install the connector and brake controller. I have attached the installation instructions for the ETBC7 kit for you, as well as an installation video of the kit on a similar 2014 CR-V.
I have attached a help article on adding electric brakes to a trailer for you.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Jacketed 2 Wire (Brake Wire) - 12 Gauge - per Foot
- Wiring
- Wire
- Jacketed Wire
- 2 Wire
- 12 Gauge
- Deka
more information >
Brake Mounting Flange for 1-3/4" Round Trailer Axles - 2K
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 7 Inch
- 1-3/4 Inch Diameter Axle
- Redline
more information >
Dexter Trailer Hub and Drum Assembly for 2,200-lb Axles - 7" Diameter - 4 on 4
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- L44649
- L44649
- For 2200 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- Dexter
more information >
Electric Trailer Brake Assembly - 7" - Left Hand - 2,000 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 2000 lbs
- Brake Assembly
- Manual Adjust
- 7 x 1-1/4 Inch Drum
- etrailer
more information >
Electric Trailer Brake Assembly - 7" - Right Hand - 2,000 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 2000 lbs
- Brake Assembly
- Manual Adjust
- 7 x 1-1/4 Inch Drum
- etrailer
more information >
Easy Grease Trailer Hub and Drum Assembly for 2K Axles - 7" - 5 on 4-1/2 - L44649 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- EZ Lube
- Pre-Greased
- L44649
- L44649
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5
- Wiring
- Wire Connectors
- Butt Connectors
- 12-10 Gauge
- Deka
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Wiring Kit for Hydrastar Electric Over Hydraulic Actuators
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Wiring
- Hydrastar
more information >
Tekonsha Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Top Load
- Trailer Breakaway Kit
- Kit with Charger
- Top Load
- Single-axle
- Tandem-axle
- Triple-axle
- LED Tester
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Testing Trailer Brake Magnets for Proper Function
- Video: Checking Out the Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies
- Video: Feature Review Replacement Magnet Kit for 10" Electric Trailer Brake Assemblies
- Shop: etrailer Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs
- Q&A: What Ohms Should Trailer Brake Magnets Be?
- Q&A: Should The Trailer Brake Circuit Have Continuity Between the Blue Power Wire and Ground?
- Q&A: Adding Trailer Brakes to Livin Lite Quicksilver 10.0 Trailer and 2011 Subaru Forester with 4-Way
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7,000 lbs
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies - 2,000 lbs
- Shop: Electric Trailer Brake Assembly - 7" - Left Hand - 2,000 lbs
- Shop: Roadmaster Battery Charge Line Kit for Motorhomes
- Shop: Curt Trailer Connector Adapter with Backup Alarm - 4-Way to 7-Way RV and 4-Way Flat
- Q&A: Does The Curt 7-Way Require a 12 Volt Charge Line To Be Connected When Brake Controller Isn't Needed
- Q&A: Parts Needed to Add 7-Way and Brake Controller on 2017 Subaru Outback Wagon
- Q&A: What are the Wire Functions of the CURT Trailer Connector Adapter, # C57102
- Q&A: What Circuits Of The 7-Way Blade Connector Are Required To Use a Curt Echo Trailer Brake Connector?
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer brake controller
- Search Results: brake controller
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Search Results: trailer brakes
- Shop: Suspension Enhancement
- Video: Detailed Breakdown of the etrailer Electric Trailer Brakes
- Article: Brake Controller Installation: Starting from Scratch