Lug Nut Torque Setting for 14-Inch Steel Trailer Wheels on 1/2-Inch Wheel Studs

Question

Question:

Hi I have a 2014 Dutchmen/Colemen travel trailer. I believe I have 14 inch tires and 1/2 in. steel lugs. Do I use the 90-120 ft. lb torque star pattern? thank you for your support

asked by: John K

0

Expert Reply:

Wheel torque specs vary based on stud diameter, wheel diameter and wheel material. The linked chart shows you commonly recommended torque specs for a range of studs and wheels.

For 1/2-inch wheel studs and a 14-inch steel trailer wheel you will use a torque range of 75-to-85-ft-lbs.

expert reply by: Adam R

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Thomas, so B and W does have a fifth wheel hitch that fits the Reese above bed rails you have in the bed of your truck but the Companion that you mentioned does not as it only fits into B and W Turnoverball gooseneck hitches. So instead what you…

view full answer...

Answer 3

I am attaching a form that shows the different torque ratings for different situations. If you were to have a 14" steel wheel with a 5 on 4-1/2" bolt pattern like what comes on the Kenda Karrier #AM32182 which fits a wheel bolt size of…

view full answer...

Answer 4

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 5

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 6

You would need to use all of the install hardware holes of the Demco Hydraulic Actuator part #DM62VR for it to be a safe install.

view full answer...

Answer 7

A 7,000 lb capacity actuator like the part #T47457207K would work great with your boat and trailer that weighs a total of 2,200 lbs. This is a multi-fit coupler that will work with virtually any hitch ball size.

view full answer...

Answer 8

I spoke to my contact at Demco and he told that the Demco Hydraulic Brake Actuator #DM62VR should not slam forward when you slow down. He said this brake actuator is inertia based, meaning as you start to apply the brakes it will begin to slowly…

view full answer...

Answer 9

In theory, we do have a solution that would turn your blocking solenoid into a bypass solenoid. The Demco Solenoid Kit for Brake Actuators with Reverse Lockouts - Bypass, part #DM5404, is designed just for this reason, to keep your trailer brakes…

view full answer...

Answer 10

For a Demco EZ latch coupler actuator like the part #DM62VR you referenced we have the etrailer pin lock part #e98887 which would work great. This pin installs in the hole between the latch and where it attaches to the ball.

view full answer...

Answer 11

For 9/16 inch suspension bolts, wet bolts or regular bolts, you will want to torque them to 65 to 95 foot pounds. And should you ever use 1/2 inch bolts then the torque spec is 45 to 70 foot pounds. And for 5/8 inch use 100 to 120 foot pounds.

view full answer...

Answer 12

Hello Mark. Based on what I could find online, the Dexter 072-042-00 is a standard 1-3/4 inch wide double eye spring which is 25-1/4 inches long and rated for 1,750 lbs. To replace these, I recommend you use the 3-Leaf Double-Eye Spring #e57SR. This…

view full answer...

Lug Nut Torque Setting for 14-Inch Steel Trailer Wheels on 1/2-Inch Wheel Studs

Product Page this Question was Asked From

Continue Researching