Replacement Swivel Trailer Jack For 1994 Mastercraft Boat Trailer

Question

Question:

I am looking for a trailer hitch to replace the worn out hitch on my 1994 Mastercraft boat trailer. It is currently an Atwood hitch that come on the trailer. I would be happy to send pictures and measurements but cant attach to this website response. The current bolt pattern of the welded on plate is. top center to center is10cm or 4 inches top to bottom holes are 7 cm or 2 3/4 inches overall plate measurements are 13.5 cm on top and 10cm or 4 inches top to bottom

asked by: Ken B

0

Expert Reply:

The trailer jacks we offer that are similar to the # FTJ120W0301 you came from all use a mounting plate that has different dimensions than what you said your trailer jack plate has. You can remove the welded mounting plate on your trailer and have a new weld-on mounting plate installed or you can use a bolt-on jack as a replacement.

The bolt-on option may be the best way to go due to the ease of installation and replacement if needed.

For a bolt-on sidewind jack I recommend part # F1413140334.This jack has a weight capacity of 1,600-lbs and features an 8-inch wheel. It is designed to work with 4 to 5 inch trailer frames. This jack has a lift height of 10-inches and swings up when not in use.

If you decide to replace the welded-on plate on your trailer and install a new jack I recommend a jack like part # FTJ120W0301 you came form. This jack comes with the weld-on bracket, snap ring, and wheel included. It has a 1,200-lb lift capacity and has a 10-inch lift. It also has a swivel feature that lets you swing up the jack when traveling.

expert reply by: Jeffrey L

0

Answer 1

The Fulton Marine Jack you referenced, part #FXP100W0301 has a lift of 10 inches. The bracket height is 14-3/4 when the jack's extended and 10-1/2 when it's retracted. The weld-on bracket is sold separately as part #P9012-00.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Swivel Trailer Jack For 1994 Mastercraft Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching