Hitch and Coupler Lock Recommendation for 2000 Chevy Tahoe and 1994 Coleman Tent Trailer

Question

Question:

I have a 2000 Chevy Tahoe and a 1994 Coleman tent trailer would this set be appropriate. Tahoe has a class IV hitch.

asked by: Rodger C

0

Expert Reply:

Yes, the combo hitch and coupler lock set part # e99039 would work great for you as the hitch lock is designed to fit 2 inch hitches like what you have and the coupler lock is a fit for the trigger type couplers your trailer would have.

expert reply by: Jameson C

0

Answer 1

The Blue Ox Base-Plate and Receiver Lock Kit is offered in a quantity of 2 as part #BX88359, 3 as part #BX88101, and 4 as part #BX88177. The tow bar arms will require one 1/2" lock each and the tow bar shank will require one 5/8" lock or…

view full answer...

Answer 2

Yes, the hitch lock of the Blue Ox Base-Plate and Receiver Lock Kit #BX88177 does fit a 2 inch hitch that has a 2-1/2 inch outer width. Your hitch being 2-1/2 inches in width overall is pretty standard.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Hitch and Coupler Lock Recommendation for 2000 Chevy Tahoe and 1994 Coleman Tent Trailer

Product Page this Question was Asked From

Continue Researching