Can I use the Timbren Axle-Less Suspension on my Boat Trailer

Question

Question:

I am thinking about installing these on my boat trailer. Will these withstand the saltwater environment?

asked by: Ben

0

Expert Reply:

Yes, the Timbren Axle-Less Suspensions # ASR5200S01 have a black powder coat finish on them that helps them resist wear and corrosion. This finish will help the axles to withstand the saltwater environment.

expert reply by: Jon G

0

Answer 1

The things you need to confirm to choose a replacement hub for your old trailer are the axle weight rating (usually noted on a sticker or plate on the axle itself), the wheel bolt pattern and the numbers of the bearings used in the existing hub. The…

view full answer...

Answer 2

We sure can! The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 3

The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

Hello Darren. Thanks for reaching out, I can definitely help with this. To convert your 2024 Brinkley Z2900 5th wheel over to disc brakes, you will need a disc brake kit, a brake line kit, and electric over hydraulic actuator, and a breakaway kit for…

view full answer...

Answer 12

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Can I use the Timbren Axle-Less Suspension on my Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching