Replacement 7-Way Recommendation for Trailer Pollak 14-117

Question

Question:

Pollak has recommended I change my fifthwheel trailer harness to a pollak 14-117inch and directed me to etrailer. I have not been able to find that part number listing on your web site. Do you carry that particular item?

asked by: Bernie

1

Helpful Expert Reply:

That part number is not active anymore but it basically is just a 7-way with wiring like our part # H20044. This is a trailer side 7-way with a 6 foot long wiring harness attached to it.

expert reply by: Jameson C

1

Answer 1

The bases for the 2 inch ball and 2-5/16 inch ball are the same for the Trailer Valet XL models, so you can swap out one diameter ball for the other. My contact at Trailer Valet says it will just take a good wrench to remove the 2 inch ball and…

view full answer...

Answer 2

The correct hardware to mount the Optronics License Plate Holder #LP35BB mostly depends on the type and thickness of the surface you want to mount it on. This plate holder has 4 pre-drilled holes for mounting and these are hidden by the plate once it…

view full answer...

Answer 3

The yellow wire of the 7-way harness part #H20044 that you referenced goes to the center pin of the 7-way which is an aux circuit that is typically used for reverse lights if present on the trailer. Normally the red wire on a 7-way (RV standard…

view full answer...

Answer 4

The Trailer License Plate Holder with LED Light #328-003-71BE uses non-submersible lights. Although this would not work well on your boat trailer, I have a different solution. I recommend using the LED Trailer License Plate Light #LPL82CBB. This…

view full answer...

Answer 5

The 4 mounting holes for Enclosed Cargo Trailer License Plate Holder #LP35BB are very small so something like an 1/8 inch self-tapping screw should be what you need. If you already have some screws that are larger there is no harm in using the holes…

view full answer...

Answer 6

Yes, you can use a 2 5/16" hitch ball, like the 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 20,000 lbs #63840, on a trailer that has a 2 5/8" Coupler. You will just want to make sure that you get the…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hi Kipp; the Blue Ox SwayPro Weight Distribution w/ Sway Control for 2-1/2" Hitch #BLU54TR will work well with this setup. The tongue weight range for this system is 1,000-1,500 lbs. With batteries and propane added to the trailer tongue you…

view full answer...

Answer 10

Hi Dennis; you aren't going to find information on the static load listed from the roof rack manufacturers. Our general guidelines for tents like the Y79XR are that the roof rack must have a minimum load capacity of 165 lbs which this rack does…

view full answer...

Answer 11

Hey Bob, I can assure you that the Thule WingBar Evo Roof Rack for Naked Roofs #TH48KG will also work with your F-250. For a black version, you can use the Thule WingBar Evo Roof Rack for Naked Roofs #TH32KG with the Evo Clamp Feet for Thule…

view full answer...

Answer 12

I am sorry Ira but it will not. The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY48GR is currently the only replacement available for the Turning Point pin box. Unfortunately, there is not a normal king pin pin box that will…

view full answer...

Replacement 7-Way Recommendation for Trailer Pollak 14-117

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching