Brake Flange Needed to Install 12 Inch Brake Assemblies With 5 Bolt Mounting Holes
Question:
I have a 1976 5th wheel single axle trailer frame with no identification on the frame or axle. I would like to convert the 12, 4 bolt electric brakes to 12, 5 bolt. The axle is 3inch and I believe 7200# rated. Will the weld on flange work for this conversion. Thank you.
asked by: Rory M
0
Expert Reply:
The brake flange that you referenced, # 4-44-1, can be welded on 3 inch axles. The brake flange will allow brake assemblies with a bolt pattern of 5 on 3-7/8 of an inch to be mounted.
The brake flange will work with 7,000 and 7,200 lbs axles.
If you are looking for brake assemblies to mount to the flanges, then I recommend the trailer brake assembly # AKEBRK-7L-SA left side and # AKEBRK-7R-SA right side. These brake assemblies will fit the 5 hole bolt pattern on the brake flanges. These assemblies are also self-adjusting brakes. These brake assemblies only need an initial adjustment when installing. After installation the brake will self-adjust.
expert reply by: Jared P
0
Products Referenced in This Question
Electric Trailer Brake Assembly - Self-Adjusting - 12" - Left Hand - 5,200 lbs to 7,000 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 5200 - 7000 lbs
- Brake Assembly
- Self Adjust
- 12 x 2 Inch Drum
- etrailer
more information >
Electric Trailer Brake Assembly - Self-Adjusting - 12" - Right Hand - 5,200 lbs to 7,000 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 5200 - 7000 lbs
- Brake Assembly
- Self Adjust
- 12 x 2 Inch Drum
- etrailer
more information >
Product Page this Question was Asked From
Brake Mounting Flange for 3" Round Axle
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 12 Inch
- 3 Inch Diameter Axle
- Redline
more information >
Similar Expert Q&A Pages
- Electric Brakes for 6,000 lb Axle With 16 Inch Wheels
- Parts Needed to Add Electric Drum Brakes to a Trailer with Tandem 5,200 lb Axles
- Where to Mount the Brake Mounting Flange 4-44-1
- Converting to Electric Over Hydraulic Disc Brakes on 5,200 lb Axle
- Replacement Brake Mounting Flange and Assemblies for 2003 Wehaul Snowmobile Trailer
- Will 5 Hole Brake Backing Plate fit Mobile Home Axle
- Brake Mounting Flange That Fits 2,000 lb Axle
- Parts Needed to Add Electric Brakes to Trailer With 12,000 Pound Air Brakes
- Dimensions for a Brake Mounting Flange for a 3 Round Axle
- Parts Needed To Replace Warner Brakes On Trailer With Standard Brakes
- Will Brake Mounting Flanges be Installed on New Axle
- Recommended Brake Mounting Flange To Welded On Brake Assemblies
- Will Brake Assemblies AKEBRK-6L and # 23-106 Both Attach to Flange 4-44-1
- Is there a Brake Mounting Flange that Has a 3 Inch Diameter Center Hole
- Recommended Nut and Washer for Use with the Brake Mounting Flange part # 4-44-1
- Left and Right Hand Assemblies for 12 " Electric Trailer Brake Replacement
- Installation of Redline Brake Mounting Flange # 4-44-1
- 5-Bolt Brake Mounting Flange for 3" Axle Tube
- Is a Gap Between a Trailer Brake Backing Plate and Drum Normal
- Dimensions of the Brake Mounting Flange # 4-44-1
- Is Trailer Brake Mounting Flange part # 4-44-1 Sold Individually
- Brake Mounting Flange Recommendation for a 1-1/4 inch Spindle on a 2006 Palomino Camper
- How to Determine the Capacity of 2 Inch Square Axle
- Parts to Convert From Electric Brakes to Electric Over Hydraulic Disc Brakes on 6,000 lb Axle
- How To Choose The Correct Brake Mounting Flange For Your Trailer Axle
- Replacement Brake Assemblies that Use 5 Hole Round Brake Mounting Flange
- Bolt Pattern of 5 Bolt Brake Mounting Flange for Trailer Brakes
- Do Electric Trailer Brakes With Parking Brake for 6k Axle Work on 7k Axle