Replacement Parts For Kar Kaddy 2 Tow Dolly

Question

Question:

I cant seem to find all the parts for my 80s model kar kaddy 2 Im trying to restore it and need to replace several parts but can not find any parts for it

asked by: Jacob J

1

Helpful Expert Reply:

I can't promise we have all the parts you need for your 80's model Kar Kaddy 2. We do have the Replacement Hub Assembly for Demco Kar Kaddy Tow Dolly - Qty 1 # DM04369 and many other parts that may work but aren't specific to your car dolly. Let me know what you are looking for and I'll see if I can help.

expert reply by: Jason S

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 6

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 9

Hey Phillip, since we know you have 3,500 lb axles we can help but it's not based on the VIN. Since we don't know what brake assembly brand you have on your trailer but we do know capacity the correct replacement assemblies are the part…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

Hello Dave, Yes, the Thule TracRac SR Sliding Truck Bed Ladder Rack - 1,250 lbs #TH43003XT-000 fits both the 2020 Ford F-350 and the F-450. This would be a great fit for your 2020 F-450 Crew Cab 4WD Dually. I attached an install video to help with…

view full answer...

Answer 12

I reached out to my contact at Demco and he said that the Kar Kaddy SS #DM9713045 can be assembled by 1 person and that it typically takes about 3-4 hours. If you are a retired auto mechanic then it will likely be on the lower end as you have…

view full answer...

Replacement Parts For Kar Kaddy 2 Tow Dolly

Product Page this Question was Asked From

Continue Researching