Recommended Trailer Hitch Receiver For 2006 Honda Accord Sedan
Question:
need a class 2 or 3 for my honda accord 2006 sedan
asked by: Richard
Expert Reply:
For a 2006 Honda Accord Sedan, there are only Class I trailer hitches available. I recommend the Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24787 for your vehicle. This is a sturdy, square tube design that has a black powder coat over an e-coat base for excellent rust protection. This hitch does not require a stabilization strap like the Curt models for this vehicle for non-trailer loads like a bike rack or cargo carrier.
If you will be doing light towing with this hitch, I recommend the Sportframe Drawbar 2-1/8" Rise or 2-3/4" Drop 2000 lb Kit # 3592. This will require a 1-7/8 inch hitch ball like # 19256 or a 2 inch ball like # 19258.
For trailer wiring or a lighted accessory, I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118302. This will connect to your factory wiring with quick connects. The connector plugs are located inside your trunk on the driver's side. You will need to remove the paneling and trunk liner to access the harness.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 9-3/4" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Towing Package for a 2007 Honda Accord
- Article: How to Measure for Trailer Hitch Drop
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: Replacement Hub for a Haul Master Kit Trailer with 30205 Bearings
- Article: Rolling on a Budget: Top Wallet-Friendly Platform Bike Racks
- Q&A: Recommended Flagpole Holder for 1-1/4 Trailer Hitch
- Q&A: What is the Difference Between Curt and Draw-Tite Trailer Hitches for a 2007 Honda Accord
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Does Curt Hitch C11327 Fit a 2006 Honda Accord Sedan with Dual Exhaust
- Q&A: 2007 Honda Accord V6 Sedan Towing Capacity and Hitch Recommendation
- Q&A: Hitch Tube Length of Curt Hitch # C11327
- Article: How to Install a Trailer Hitch