Can the Safety Tab Be Removed on Class I Trailer Hitch Receiver for a 2008 Nissan Altima
Question:
The bike rack I am trying to slide in will not line up with the holes. Is there a way to chip off the safety nipple/nub inside the 1-1/4 receiver?
asked by: Eddie F
Expert Reply:
The tab on the inside of the trailer hitch receiver for your 2008 Nissan Altima is meant to ensure that the user only uses Class I rated accessories in the hitch. As you can see in the attached photo.
This is more of a safety precaution as Class I receivers like # 24796 cannot handle much weight especially if that weight is sticking out further from the receiver. It could damaged the receiver and ultimately damage your accessory (in this case your bike rack and bike).
To answer your question, ultimately you can remove the tab if you really want to, but doing so will void your warranty and could eventually lead to your receiver and/or your accessory becoming damaged. I do not recommend going this route.
I recommend going with a bike rack that is rated for a Class I receiver, and I have linked our selection for you below.
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Suspension Enhancement
- Q&A: Hitch System to Haul a 250 Pound Motorcycle With a 2010 Nissan Altima
- Search Results: lt37467
- Search Results: silicone
- Search Results: ball
- Search Results: motorcycle trailer
- Search Results: pin and clip
- Search Results: trailer hitch ball
- Video: Feature Review etrailer Trailer Coupler Lock for Flat Lip 1-7/8" and 2" Ball Couplers
- Video: Mount: Draw-Tite Sportframe Trailer Hitch Receiver on a 2014 Nissan Maxima
- Video: Comprehensive Review: Loctite RTV 598 High-Performance Silicone Gasket Maker
- Video: Dutton-Lainson Hand Winch w/ Automatic Brake Review
- Video: Best 2010 Nissan Maxima Hitch Options
- Video: Pin and Clip for 1-1/4" Hitches Review
- Video: An In-Depth Look at the Curt Towing Starter Kit for 1-1/4" Hitches
- Shop: etrailer Trailer Coupler Lock for Flat Lip 2-5/16" Ball Coupler - Aluminum - Yellow
- Shop: Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Shop: Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
- Shop: etrailer Trailer Hitch Receiver Lock for 1-1/4" Hitches - Flush - 2-1/8" Span - Chrome
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Brake Controller
on Trailer Hitch
