Pin Hole to Hitch Opening Distance on 2 inch and 1-1/4 inch Hitches
Question:
Is there a standardized distance from the opening of the receiver and the hitch pin hole? Does it change according to the class of the hitch and the weight rating? Does it matter where the hole is? I would think that the hole distance would limit what attachments could be used in it... Thanks for any advise you can offer.
asked by: Dick G
0
Expert Reply:
Typically the distance from the center of the hitch pin hole on a 1-1/4 inch hitch to the face of the opening on the hitch measures 2 inches whereas on a 2 inch hitch the distance is 2-1/2 inches.
expert reply by: Jameson C
0
Product Page this Question was Asked From
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Similar Expert Q&A Pages
- Will the Draw-Tite 3594 Get Me Close to 16 of Rise if My Hitch is 11 1/2 Off the Ground?
- Trailer Hitch and Wiring for a 2016 Subaru Impreza Sedan
- Why do Some Ball Mounts Have a Drop and Rise and Others Only have a Rise
- How to Measure Ball Mount Rise for Draw-Tite Sportframe Ball Mount # 3594 on a 2002 Buick Regal
- 1-1/4-Inch Ball Mount with 4-Inches of Drop
- Dimensions Of Draw-Tite Sportframe Ball Mount # 3594
- Ball Mount For 1-1/4 Inch Hitch On a 2002 VW Beetle with 4 Inch Rise
- Towing a Trailer with 2014 Mustang GT vs 1999 Honda Civic Coupe
- How to Determine Where Ball Mount Platform for 3594 Will End Up When Installed on 1998 Buick Regal
- Will Sportframe Drawbar # 3594 Fit Kubata RTV Receiver
- Does Suspension Sag Factor When Picking Out Correct Rise/Drop Ball Mount
- Ball Mount Recommendation for a 2014 Subaru Forester with a Curt Hitch # C12100
- Will Thule EasyFold XT Fit A Class 1 Trailer Hitch with 1-1/4 Distance from Hitch Pin Hole
- Lock Pin Hole Measurement for Class I Hitch
- Recommended Ball Mount Draw Bar For 1-1/4 Inch Trailer Hitch Receiver With 4 Inch Rise
- How to Measure to Determine How Much Drop Is Needed for a Ball Mount
- Which Ball Mount and Hitch Ball Should I use with My Draw-Tite 24797 on my 2009 Kia Rondo
- What is the Proper Rise/Drop Ball Mount for a 2006 Honda Civic
- 7-Way for 2017 Honda CR-V and Ball Mount With 2 Inch Hitch Ball
- Recommended Ball Mount for 2010 Ford Fusion Towing Haul Master Trailer
- How to Pick Out Correct Ball Mount for 2015 Ford F-150
- Which is Correct Ball Mount for 1997 Chevrolet Lumina w/ Draw-Tite Trailer Hitch # 24628
- Ball Mount Recommendation that is 4 inches Shorter than the Sportframe Ball Mount part # 3594
- Compatibility of the Sportframe Drawbar and a 2 Inch Trailer Ball With 3/4 inch Shank
- How To Determine What Size Ball Mount Will Fit On 2006 Chevy HHR
- Trailer Hitch Receiver And Wiring Harness To Tow or Use a Bike Rack On a 2021 Toyota Prius XLE AWD-e
- What Ball Mount is Needed For 15 Inch Hitch Height With Draw-Tite Receiver 24872 on 2014 Ford Focus?
- What Is The Highest Capacity Trailer Hitch Available For A 2021 Mazda 3 Hatchback?
- 2018 Hyundai Sonata Parts Needed to Tow a Trailer