How to Clear Error Code on Lippert Ground Control Leveling System

Question

Question:

I have an error code that says L F jack. it says to retract all jacks and hit enter to clear. i have tried that and a bunch of other things and still cannot get the error code to clear. sometimes the location of jack changes on display but always results in the same way. only had the camper for 2 weeks. it is a 2016 326rds cougar fifth wheel. any suggestions?

asked by: T.J. K

0

Expert Reply:

We have heard of this issue before on the Lippert Ground Control systems # LC358590.

Here is the recommended procedure for clearing the error code: Extend all jacks at least 6 inches. Then press and hold the RETRACT button until the jacks begin retracting. All of the jacks should fully retract and clear the error.

If that does not clear the error code disconnect all connectors to let the system power down completely for about 15 minutes. The re-connect and follow the procedure again if the error code reappears.

expert reply by: Adam R

0

Joe

6/21/2020

I’m having the same issue with my Lippert gen 3 system. Battery died during leveling. Now the error won’t go away no matter what I do. Holding auto retract seems to cause an issue too. I swear my leveling system was made by the government. I have more problems with this leveling error than anything else.

Reply

Chris R.

6/24/2020

If following the method described above didn't clear the error the best I can suggest is to completely disconnect the system from power and then hook it back up, hopefully resetting everything and resolving the issue.

Reply

Dean K.

4/25/2021

@ChrisR I have a RR jack error and have tried everything I’ve found on restring the error, but the jack will raise.

Reply

Jon G.

4/28/2021

@DeanK If you have followed the instructions in the manual by checking the harness connections at the controller and at the jack, checked the harness for damaged, and checked the fuses at the controller, and everything looks good then it sounds like there might be one of those components that needs replacing.

Reply

See All (9) Replies to Joe ∨

Answer 1

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 2

Self-adjusting brakes #AKEBRK-7-SA do not require that you travel in reverse for them to adjust. They can adjust themselves going forward or backward. Keep in mind that even self-adjusting brakes require 1 initial adjustment. You could just install…

view full answer...

Answer 3

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 4

On the Lippert Ground Control 3.0 #LC358590 the error you are receiving indicates either a problem at the left front jack, a hall signal issue (open ground/short, or other malfunction) or an unexpected high amperage current stall (meaning the battery…

view full answer...

Answer 5

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 6

The American CS6000XL that you referenced is no longer available and there isn't a direct replacement for it but the closest solution as a replacement would be the Progressive Dynamics RV Control Center part #PD4560K18LS8 which as the same…

view full answer...

Answer 7

The Replacement Converter #PD4655V is the correct converter for your Parallax 7355 power center. I do not see that WFCO shows their 8955PEC being acceptable to use with your Parallax 7355.

view full answer...

Answer 8

The only way to determine what your pin box's bolt pattern is would be to either get the serial number/RPO number off the tag on the pin box or to use the attached guide below to measure the bolts and crossover those measurements on the included…

view full answer...

Answer 9

Yes, you can use the Furrion Chill HE RV Air Conditioner System - Manual - 15,000 Btu - White #FR92PR to replace your old 68RV15102A.

view full answer...

Answer 10

For your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC675817 or #LC358590 you need to reset the leveling memory. The “Zero Point” is the programmed point that the trailer will return to each time the Auto Level feature is used…

view full answer...

Answer 11

I have a solution for you but there is not a direct replacement for your old Atwood unit. Instead, you can use the 2-Wire RV Propane Gas and Carbon Monoxide Detector - 12 Volt - White #RS34FR to replace your old Atwood carbon monoxide detector, but…

view full answer...

Answer 12

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

view full answer...

How to Clear Error Code on Lippert Ground Control Leveling System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching