Height of the Mounting Bracket for the Rhino-Rack RLTP Legs # RRRLTPFC-3

Question

Question:

says 2 inch but how much does the Transit adapter/bottom piece add?

asked by: TL

0

Expert Reply:

I went out to the warehouse and found that the mounting bracket on the Rhino-Rack RLTP Legs # RRRLTPFC that come with the Rhino-Rack RLTP Legs for Factory Fixed Mounting Points # RRRLTPFC-3 measured about 1-1/4" tall (see attached picture).

expert reply by: Jon G

0

click to enlarge

Answer 1

The spindle that you referenced, part #TRU47FR, will work great for you. This spindle features a 4 inch long stub, and is rated for a 3,500-lb axle. I have attached a link to a product review video for this spindle you can check out. The installation…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

Tire designations ST205/75D14 and ST205/75R14 are both for special trailer tires with a 205mm width, 75-percent aspect ratio and that fit a 14-inch wheel. The difference between them is the tire's type of construction. The ST205/75D14 tire is a…

view full answer...

Answer 11

Karrier and Loadstar are two different brand names used by Kenda. There's no difference in quality or function between the two brand names. For a ST175/80-13 Radial trailer tire in load range D, I'd recommend part #AM10210 if you're…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Height of the Mounting Bracket for the Rhino-Rack RLTP Legs # RRRLTPFC-3

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching