4-Pole Flat Wiring Harness for 2008 Nissan Frontier

Question

Question:

Will new plug have ALL trailer lights work?? Enclosed trailer. Has clearance lights.

asked by: Jerry

0

Expert Reply:

The # HM43575 would work as a replacement, you would need to unplug your current harness and plug in the Hopkins in the 4-pole connector slot; you can see exactly where in the photo I've provided. I've also attached a link to a video review of this product for you to take a look at.

expert reply by: Kyle S

0

click to enlarge

Jerry

1/8/2018

Will new plug have ALL trailer lights work?? Enclosed trailer. Has clearance lights.

Reply

Kyle S.

1/8/2018

The Hopkins Plug-In Simple Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector # HM43575 would power all of your trailer's signal lights. However, it is compatible with a 7-way adapter such as # 30717 which you may need depending on your wiring. I have attached a link to a help article on trailer wiring for you to take a look at as well which details the functions of the connectors.

Reply

Louis P.

4/29/2020

Hi. Im connecting a 4-pole where a 7-pole was on my 2010 Frontier. After I connect the 4-pole, what should i do with the other plug on the 7-pole? Unplug it, or leave the plug in and cut off the wires so as to protect the plug?Thanks!

Reply

Chris R.

4/30/2020

I'm not quite sure what you mean by the additional plug on your Frontier. Are you talking about where the 4-Way (and existing 7-Way) plug into the factory wiring?

Reply

Answer 1

I have exactly what you need to install a 7-way trailer connector on your 2015 Jeep Wrangler Unlimited. It sounds like you have the factory tow package therefore, all you would need to do is remove the 4-way you have now and replace it with the…

view full answer...

Answer 2

Yes, you just have to remove the old lights, match the wires and mount the new ones. Please note, that it is usually not a good idea to mix LEDs and incandescent lights, so if you have have side markers or other lights on the trailer, make sure you…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

4-Pole Flat Wiring Harness for 2008 Nissan Frontier

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching