Ball Mount and Ball Recommendations for a 2010 Subaru Forester
Question:
I have Hidden Hitch class III 87493 and now need to find mount and ball to tow a trailer with 2010 Subaru Forrester. Was going to order standard fixed mount and ball but then looked at extended length mount BM20 and now am confused. Also tried to online without pin as my bike rack has a locking pin I can use, but system won't let me just the pin.
asked by: Dan
Expert Reply:
The recommended ball mount for your 2010 Subaru Forester is the Ball Mount # D-4, this is what I would recommend you get also. The Extra Long Ball Mount # BM20 that you referenced would most likely not be necessary, unless you have the need for a very long ball mount. You'll also need the Hitch Pin and Clip, # PC3.
Whichever ball mount you choose you should always stay under the towing capacities of the lowest rated component in your towing setup and go with the lowest rated component as the overall towing capacity for your setup.
For a ball you have a couple options, but it really depends on what ball size the coupler on your trailer has. If you need a 2 inch ball I would recommend a Hitch Ball # 19247, if you need a 1-7/8 inch ball I would recommend a Hitch Ball # 19260.
I attached an FAQ page on balls for you to check out.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Brophy
more information >
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: How to Figure Weight Capacity When Using a Hitch Extender or Extra Long Ball Mount
- Q&A: Difference Between Brophy # BM20 and # BH20 Ball Mounts
- Q&A: Safety of Using Hitch Extender and Other Options To Clear Spare Tire on Jeep Liberty
- Q&A: Stowed Length of ARK ORJW1SU Off Road Trailer Jack
- Q&A: Will Extreme Ratcheting Trailer Jack Keep Moving Forward without Handle if in Forward Position
- Q&A: Is 770 Lbs for the Extreme Off-Road Ratcheting Trailer Jack Trailer or Tongue Weight
- Q&A: Extended and Retracted Height of ARK ORJW1SU Extreme Off-Road Ratcheting Trailer Jack
- Article: Hitch Adapters and Extenders
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Article: Stability Control for Heavy Duty Vehicles
- Article: Which Sway Control Hitch is Right For Your Trailer?