Can Weight Distribution System Tow Trailer without Spring Bars Connected

Question

Question:

I have a 2007 keystone outback bumper pull camper. I also have a 2010 v8 f150 to pull it with. However the newly purchased preowned camper is not equipped with the pieces in the toung to attach the weight dust. bar chain and the sway bar. Can I pull it with just the ball and safety chains?

asked by: Jimmy O

0

Expert Reply:

You can tow a trailer with a weight distribution setup that does not have the spring bars connected. As long as the head of the system is attached to the shank properly (there's no reason it wouldn't be) it would work just as well as a standard adjustable ball mount.

expert reply by: Jameson C

0

Bill

7/7/2020

I lost a spring a bar while traveling. Should I continue to use the remaining Spring bar or take it off and use the hitch without the spring bars?

Reply

Chris R.

7/10/2020

I would definitely remove the remaining spring bar until you're able to replace the missing unit. If you can tell me what model system you have I would be happy to find the right spring bar.

Reply

Answer 1

Yes. If you don't need the weight distribution bars attached to carry the trailer to storage, you can absolutely use just the WD hitch head and ball to tow the trailer. It will work just like a ball mount.

view full answer...

Answer 2

You can back up a trailer with a weight distribution system installed on as long as you don't end up in too tight of a turn. This is especially true with the Curt Weight Distribution System part #C17422 as it has a friction sway control system as…

view full answer...

Answer 3

A weight distribution system does not increase a hitch's tongue weight capacity. Rather, it takes weight off of the tongue, helping loads stay stable and level. In other words, if you use a trailer without a weight distribution system with a…

view full answer...

Answer 4

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 5

Since most trailer manufacturers do not make wheel and tire information available to the general public, it is hard for me to tell you what size lug nuts you have on the wheel. I can tell you they do have caps over them. The most common size of lug…

view full answer...

Answer 6

The Traffic Cone Holder, #RA-26, that you mentioned is designed to store cones that are 12" - 36" tall, and the arm of the holder is 22-3/8" long. The arm does not fold down a full 90 degrees, so this would not be the best option for…

view full answer...

Answer 7

So there isn't a 6 inch hitch extender for a 2 inch hitch that has an 11,000 lb capacity and 1,200 lb tongue weight capacity, and hitch extenders also reduce the capacity of your hitch by 50 percent, so they are generally just used for…

view full answer...

Answer 8

Yes, you can install the Rear View Safety Backup Camera System with Side Cameras Item #RVS-062710 to have the side cameras come on when a turn signal is engaged. There are instructions that explain different ways the cameras can be activated and this…

view full answer...

Answer 9

I recommend looking at the Equal-i-zer Weight Dist Shank - 18" Long - 8" Rise, 4" Drop - 600 to 1,400 lbs TW #EQ90-02-4600. This is 18" long and has a max tongue weight of 1,400lbs, whereas the Equal-i-zer Weight Dist Shank -…

view full answer...

Answer 10

If the trailer hitch on the motorhome has a separate capacity for use with a weight carrying hitch then you can use one. The hitch will distribute the weight from the rear of the vehicle to the front where you need it. The amount of weight…

view full answer...

Answer 11

The 7-Way RV Upgrade Kit #ETBC7L you were looking at is exactly what you need. The yellow wire will connect to the reverse light circuit on your 2021 Highlander XLE to power the reverse lockout solenoid on your brake actuator. This kit comes with the…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Can Weight Distribution System Tow Trailer without Spring Bars Connected

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching