Replacement Kwikee 32 Series Step Recommendation for 1990 Fleetwood Southwind

Question

Question:

I have a 1990 Fleetwood southwind the current steps are a kwikee # 3258 w/ a 8inch rise and 9inch run steps are 11inch deep with a 8inch x 22 mounting Am I correct in ing model # LC372261 as a replacement?

asked by: Dennis J

0

Expert Reply:

Since what you have currently on your 1990 Fleetwood Southwind is a Kwikee 32 step the Lippert Kwikee 32 powered step part # LC372261 that you referenced would be the correct step for you to use.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Doug, That's a good question because fit is really important so the cover stays snug on your trailer, and there is a specific way to measure for the etrailer covers. It's pretty simple, and what you want to do is measure the body of the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 7

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 8

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 9

Junic, I did some research it looks like the 770 monitor will work with all other TPMS's as long as they have a date code of 4519 (45th week of 2019) or newer. If your sensors are older, then you'd need to use the 507 display; #TST-507-D-C.

view full answer...

Answer 10

Hey Todd, yes the Solera 2000 Series and Edge Hardware part #LC65AF does come with two arms and the right hand side does have the drive motor but the wires do not come out of the top of the drive motor so you might email me a picture of what you have…

view full answer...

Answer 11

Marty, it sounds like you're looking for the Replacement Short Arm Assembly for RV Awnings #LC404523. This is going to replace any Lippert Solera short arm assembly, measures 63" long, and includes the wall-mounted bracket, outer arm, inner…

view full answer...

Answer 12

Hello Stephen. The Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks #RM-2460-2580 will work great on your 2024 Brinkley Z3110 5th wheel since it has 3" diameter axles. The Comfort Ride kit will make huge improvements in ride quality…

view full answer...

Replacement Kwikee 32 Series Step Recommendation for 1990 Fleetwood Southwind

Product Page this Question was Asked From

Continue Researching