Recommended A-Frame Jack with Most Ground Clearance
Question:
I would like to know how long the outer tube extends below the A-frame flange. That is the one dimension that is missing in your great video and data sheet. please measure the length from the bottom of the flange to the bottom of the outer tube. I am hoping it is not less than 3 1/2 inches. Our 4-H utility trailer already has the lower support plate installed. The thickness from the top face of the A-frame to the bottom face of the lower support place face is about 3 1/2 inches. I need the jack to be able to tuck up tight so it doesnt drag on driveway or other steep bends in a roadway or rocks in middle of the roadway. Thanks.
asked by: Jeff
Helpful Expert Reply:
The distance from the bottom of the mounting flange to the bottom of the outer tube on the Bulldog Round, A-Frame Jack part # BD155033 is 3-1/2". The mounting flange is 3/16" thick. I have attached a photo of these measurements for you as well. If you need something with even more clearance then the only other option we have is the Ultimate Trailer Jack part # 322-RDJ-2K which measures 1-3/4" with the jack fully retracted and the collar at the lowest setting.
I have attached a review video of both jacks for you as well.
Products Referenced in This Question
Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Topwind Jack
- 28 Inch Lift
- Bolt-On
- Weld-On
- With Rectangle Foot
- Ultimate Jack
more information >
Product Page this Question was Asked From
Bulldog Round, A-Frame Jack - Topwind - 15" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Topwind Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
Continue Researching
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness - Dash Knob - 1 to 2 Axles - Proportional
- Shop: Tekonsha Primus IQ Trailer Brake Controller w/ Custom Harness - 1 to 3 Axles - Proportional
- Shop: Bulldog Round, A-Frame Jack - Topwind - 15" Lift - 2,000 lbs
- Shop: Pro Series Round, A-Frame Jack - Topwind - 15" Lift - 2,000 lbs
- Shop: Brake Controller
- Video: Comprehensive Review: Bulldog Round, A-Frame Jack
- Shop: Round A-Frame Trailer Jack - Topwind - 14-1/4" Lift - 2,000 lbs
- Shop: Bulldog Round, A-Frame Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Trailer Wiring
- Shop: Gooseneck Hitch
- Search Results: bd155033
- Search Results: surge actuator
- Video: B and W Underbed Gooseneck Trailer Hitch Installation - 2018 Chevrolet Silverado 2500
- Video: Dexter DX7.5L A-60 Brake Actuator Review
- Search Results: trailer jack pin
- Search Results: hitch pins and clips
- Search Results: surge brake actuator brake actuator
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Search Results: trailer jack
- Video: Breaking Down the Curt Wheel Chock Set w/ Handles and Mounting Brackets
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: How Much Does a Boat and Trailer Weigh?
- Video: Hands-On with the Replacement Consumer Lockout Key for Dexter Axle Brake Actuators
- Search Results: surge coupler
- Q&A: Troubleshooting Edge Programmer that Won't Power On When Plugged into Vehicle
- Video: Review of Curt Gooseneck Hitch - Ball and Safety Chain Loops for Chevy Ford GM Nissan - C38CR
- Video: Curt Ball and Safety Chain Loop Kit Installation - 2020 Chevrolet Silverado 2500 C38CR
- Shop: Trailer Hitch
- Q&A: Advice on Replacing Old Surge Brake Coupler with Non Surge Straight Box Coupler Shaft