What Tow Bar and Adapter Will Work With a Fab Fours Grumper Bumper on a 2011 Jeep Wrangler

Question

Question:

Ok thank you, and what wiring harness do I need from motor home to jeep and if I pull a trailer behind Jeep what harness will I need to pull both Jeep and trailer behind motor home?

asked by: Jason

0

Expert Reply:

In order to find out which towbar and d-ring adapter will work with the Fab Fours Grumper Bumper on your 2011 Jeep Wrangler you will need to take two measurements, the thickness of the d-rings and the diameter of the pin hole. I was not able to locate this information on Fab Fours site which is why you will need to measure this for yourself.

If they measure to be 3/4" thick with a either a 7/8" or 1" diameter pin hole then you can use the Adapter for Jeep D-Ring Bumper Mounts part # RM-035 but if they measure to be 1" thick with a either a 7/8" or 1" diameter pin hole then you can use the Adapter for Jeep D-Ring Bumper Mounts part # RM-035-1. There are other Fab Fours bumpers that use the 3/4" thick d-ring so I believe it should be correct for you as well.

These d-ring adapters can then be used with the following tow bars:

Falcon 2: part # RM-520
Nighthawk All-Terrain: part # RM-676
Falcon All-Terrain: part # RM-522
Sterling All-Terrain: part # RM-576
BlackHawk 2 All-Terrain: part # RM-422

I really like the Falcon All-Terrain part # RM-522 because you get a lot of great features for a reasonable price. I have attached a review video for you. I would also recommend checking with the manufacturer to make sure the bumper can be flat-towed.

expert reply by: Conner L

0

Jason

11/12/2018

Ok thank you, and what wiring harness do I need from motor home to jeep and if I pull a trailer behind Jeep what harness will I need to pull both Jeep and trailer behind motor home?

Reply

Conner L.

11/12/2018

For starters, we do not recommend triple towing with your motorhome nor are our products designed to do so. Also, in some states it is illegal so you will need to check this beforehand as well. The issue is going to come down to powering the trailer lights because the owner's manual for your 2011 Jeep Wrangler requires that the battery be disconnected. In order to power the Jeep tail lights I recommend using the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267. This kit is very popular for Jeep owner's and we even have an install video on a similar 2014 model which I have attached for you. Unfortunately, I don't have any solutions for you to then power the trailer lights as the power would need to come from the motorhome (battery disconnected on Jeep) and the tail light circuit on the motorhome would need to be rated for the power draw of both the Jeep and trailer lights which is a lot to ask.

Reply

Answer 1

The Roadmaster Falcon 2 Tow Bar, #RM-520 you refer to is a great option. I prefer the Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar w/ LED Lights, #RM-676, it has a little heavier rating and has all the bells and whistles with it. You can use…

view full answer...

Answer 2

You need five basic components to safely flat tow any vehicle, base plates, tow bar, safety cables, indicator lights wiring solution and supplemental braking. For your 2022 Jeep Gladiator Mojave, I recommend: - Base Plate, Roadmaster Direct-Connect…

view full answer...

Answer 3

In order to flat-tow a 2021 Jeep Gladiator you'll need base plates, tow bar, safety cables, supplemental braking system, and a lighting kit. The Jeep is pretty easy to setup for flat-towing and you'll only need the basics for this. I have…

view full answer...

Answer 4

Hey David, If your 1994 Jeep Wrangler has the factory bumper then I recommend the Demco Classic Base Plate Kit #DM9518112 along with the etrailer SD Non-Binding Tow Bar #e34ZR to complete your physical connection between the motorhome and Wrangler.…

view full answer...

Answer 5

Whether or not you can flat tow with a Jeep bumper is really up to the manufacturers testing; some of the big names like MetalCloak or Poison Spyder have bumpers with D-ring attachments that can be used for flat towing connections. This is great…

view full answer...

Answer 6

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 7

We do offer tow bar setups that can attach to the D-rings on the Warn Elite Bumper. You will need to use a D-ring adapter to connect the tow bar. For the adapter you have the following options: 1" Thick D-Rings #RM-035-1 3/4" Thick D-Rings…

view full answer...

Answer 8

The easiest to use and highest quality base plate kit that fits your 2023 Jeep Gladiator is the Blue Ox part #BLU53FR which would work great with a tow bar like the #BX7420. We do have custom fit lighting solutions like the Curt part #C96JR that…

view full answer...

Answer 9

I do have a solution for you, however you will not be able to use a pin on your existing 4-Way for a battery charge line.In order to run charge line from the RV to your 2008 Jeep Wrangler battery, I first recommend installing the Roadmaster 6-Wire…

view full answer...

Answer 10

Based on the information you have given me you have the Roadmaster Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars #RM-035 or #RM-035-1. Since you want to stick with Roadmaster parts, the correct replacement pin is the…

view full answer...

What Tow Bar and Adapter Will Work With a Fab Fours Grumper Bumper on a 2011 Jeep Wrangler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching