Will the Hands Free Liftgate Feature Still Work on a 2019 Acura RDX with Draw-Tite Trailer Hitch

Question

Question:

I have a 2019 RDX Advance pack front wheel drive. Will the trailer hitch part 76268 stop the use of my kick to open rear hatch.

asked by: Thomas

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76268 which is a fit for your 2019 Acura RDX with Advance Package will not impede the use of your hands free liftgate sensors. However, you will need to position your foot to either the right hand or left hand side of the receiver tube opening in order for them to read.

expert reply by: Conner L

0

Diego C.

6/28/2020

Just wanted to double check I saw an expert say that hitch 76268 will not interfere with the tailgate sensor on the 2019 acura rdx? Also is there a sensor relocation kit in the works if it does interfere?

Reply

Chris R.

7/1/2020

Unfortunately it's a little "hit or miss" with regards to the liftgate sensors on your Acura RDX. In most cases the Draw-Tite # 76268 should only interfere to the point of having to move your foot to either side of the hitch receiver, but we have had a couple customers come back and say it completely blocked theirs. The factory location of the sensors can vary just a tad and it only takes an inch or two off to make the difference. You can check with a local Acura dealer about a potential sensor relocation kit but at this time it's not something we have available.

Reply

Answer 1

The crossbar of the Curt 13423, which we refer to as part #C95CR is exposed, just like the Draw-Tite #76268 would be. I've linked to a photo showing what the Draw-Tite 76268 hitch looks like once installed, the Curt #C95CR would look almost…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C95CR will fit on 2021 Acura RDX, but with the factory trim piece it will not be very hidden. This receiver does offer a simple bolt-on installation process and requires no drilling…

view full answer...

Answer 3

The Draw Tite hitch part #76268 fits only the 2019 Acura RDX at this time (August 2019). If you have a different vehicle let me know and I can recommend a hitch for it as well.

view full answer...

Answer 4

I definitely have those measurements! I pulled the Draw-Tite Hitch #76268 from the warehouse and measured it for you. From the front of the hitch receiver tube, the center of the pinhole is 2-3/8". From the rear of the receiver tube, the center…

view full answer...

Answer 5

We personally don't have any photos as of yet (February 2019) as we haven't had a chance to install the Draw-Tite #76268 on a 2019 Acura RDX but I do have a picture from the installation instructions which I have attached for you to check…

view full answer...

Answer 6

When installing the Draw-Tite Trailer Hitch Receiver #76268 on your 2020 Acura RDX you will remove the rubber isolator from the silver prongs (hanger) with either exhaust removal pliers or a simple pry bar. I have added a link to the instructions for…

view full answer...

Answer 7

Correct, the Draw-Tite Max-Frame Trailer Hitch Receiver part #76268 which is a fit for your 2019 Acura RDX does indeed sit below the rear spare tire. Generally speaking, hitch manufactures will position the receiver tube so it does not stick out past…

view full answer...

Answer 8

When installing the Draw Tite hitch part #76268 on your 2019 Acura RDX there is no need to remove any rear fascia or panels. It simply gets bolted into place and hangs below the rear bumper. See attached picture to see what it looks like installed.

view full answer...

Answer 9

According to the installation instructions for the Draw-Tite Max-Frame Trailer Hitch Receiver part #76268 which is a fit for your 2019 Acura RDX, the exhaust must be lowered temporarily in order to position the hitch up under the vehicle. If you are…

view full answer...

Answer 10

The Draw-Tite Class III hitch you specified, part #76268 has two holes in each side of the receiver tube. The larger 5/8 inch diameter hole is meant for the hitch pin. The smaller hole is not used. So, in regards to your question-the larger hole is…

view full answer...

Answer 11

Typically the distance from the center of the hitch pin hole on a 1-1/4 inch hitch to the face of the opening on the hitch measures 2 inches whereas on a 2 inch hitch the distance is 2-1/2 inches.

view full answer...

Answer 12

Curt Manufacturing lists the #C22HR Class III hitch as a fit for all models of the 2022 Acura MDX. Installation will not require removing the bumper cover. If your spare tire is mounted to a wheel larger than 18 inches in diameter, the spare will no…

view full answer...

Will the Hands Free Liftgate Feature Still Work on a 2019 Acura RDX with Draw-Tite Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching