Recommended Flat Tow Setup for Blue Ox Tow Bar on 2008 Honda CR-V

Question 1

Question:

I received a Blue Ox hitch with the motorhome I purchased. It has a patent number 5224960, I think it is a model BX4330. It is outfitted with a ball about 4inch diameter where the regular ball coupler would be. On the 4inch ball is a tongue that goes into the receiver. I need a base plate for the car, the lighting kit, a switch and wiring to jump past the fuse that is supposed to be removed when towing. I think thats all I need.

asked by: Chris D

1

Helpful Expert Reply:

For your 2008 Honda CR-V, you will want to start with the Blue Ox Base Plate Kit - Removable Arms # BX2246 which will be directly compatible with your tow bar. The tow bar you are describing is likely the old alpha or avail model, either of which will work just fine. If you want to determine which model you have, you can find it printed on the driver's side leg under the latch handle according to my contact at Blue Ox. If you don't have the safety chains, you will also want # BX88196.

Then for your tow bar wiring, I recommend the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 which will utilize your factory wiring for a clean look while protecting your electronics from overload. The Roadmaster FuseMaster Fuse Bypass - 13" - 20-Amp Mini-Fuse # RM76511 is what you were seeking to avoid pulling fuses each time you tow. I also recommend the charge line kit # RM-156-25 to maintain your vehicle battery while towing.

If you already have a supplemental braking system, then you are almost to a complete system, but if you do not then I recommend the SMI Stay-IN-Play DUO Supplemental Braking System # SM99251. This system will apply the brakes in your CR-V at the same time and with the same intensity as you apply the brakes in your Motorhome. This system requires no adjustment after the initial installation set-up and becomes a plug and play system that literally requires just a flip of the switch. It is a favorite with our customers because of the ease of use.

Finally, you will need a high low adapter. I've attached an article to help you with the measurements for safety and have linked the page to your options.

click to enlarge

helpful expert reply by: Jason S

1

Question 2

Question:

I think I have an incorrect wiring harness for my car. I think I ordered as suggested by someone. My car is a separate turn signal, break light and tail light system. I'm thinking I really need part number 154-792-118158. Can you confirm? The coach is a separate system too. I guess I would have to return we I originally received. I was successful at installing the tow plate. Bigger job than what it appears. Ha, I got it though. Thanks.

asked by: Chris D

1

Helpful Expert Reply:

The Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting # 154-792-118158 you referenced is a fit for your 2008 Honda CR-V as is the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267 I recommended if that is what you received. For the separate turn on the motorhome and the separate turn on your vehicle (both 3 wire systems) you simply need two more diodes. I recommend the Roadmaster Hy-Power Diodes (Qty 2) # RM-792 with that 7-way to 6-way which gives you the battery charge line option I recommended previously of the # RM-156-25. I've attached a diagram to help further.

click to enlarge

helpful expert reply by: Jason S

1

Question 3

Question:

Now I feel like a bit of a pain, but at least one more question . I want to outfit the coach with an indicator light running from the dinghy to the cockpit of the coach which will light when the dinghy breaks are applied. I feel like this is almost a necessary safeguard against a potential situation which could lead to bad consequences. Thank you for your time and guidance.

asked by: Chris D

1

Helpful Expert Reply:

No problem at all. This is a good idea. You can simply use a led strip like # UCL90CB and tie it into your brake lights and blinkers on your 7-way trailer connection. This gives you a 120 degree viewing so you can mount it to the underside of your coach. They can be cut and rejoined to you can add the length you desire. I've attached a video to assist.

click to enlarge

helpful expert reply by: Jason S

1