Curt Hitch C14011 Installation on 2001 Ford Excursion
Question:
I have a 2001 Excursion that the factory cross pin hole on the receiver has been ground oblong from use. So, when you put a hitch in the receiver and install the pin there is a significant amount of play front to back that allows the hitch to slide within the receiver. I plan to replace the worn out factory hitch with this one. Im having an autoshop remove the old one monday. Its pretty rusted in Ohio car. I have a few questions.. 1. If they break the bolts off, as I understand it the weld nuts on the back are removable. Do you sell replacement weldnuts that can be used to use the stock screws that come with this hitch? if not, do you sell block washers that would allow the bolts to be run from top down instead of bottom up? That would allow me to install it the same way the TorkLift LF1006 is installed. 2. Curts instructions show the finished install with the factory electrical plug mounted using the factory bracket. From what I can see, the factory bracket is bolted to the top of the factory hitch. I can remove that, but I dont see a pre-drilled and tapped hole in the photos of the curt hitch to accept that bracket. Will I have to drill that to use the factory bracket? If so, do you know the size/thread? Thanks.
asked by: Tom
Expert Reply:
You will naturally be better off if your shop does NOT break off the factory weld nuts when removing the OEM hitch from the frame rails on your 2001 Excursion. Given the vehicle's age its quite likely that the bolts securing the OEM hitch will have some rust. Application of a solvent like PB Blaster or WD40 will help dissolve that accumulated corrosion and give them better odds of getting the hitch off without damage so that you can install either Curt hitch # C14011 or TorkLift # TLF1006.
Both of these hitches are made to install using your factory weld nuts and they both include the matching hardware. We do not offer replacement weld nuts.
If you can access an open end of the frame to get to the place where the weld nut broke off your shop could potentially fish wire a new carriage bolt in place of the weld nut. Otherwise you may have to weld the hitch on or see if your local garage could come up with a way to re-weld in a weld nut to match the hitch hardware. Both the Curt # C14011 and the TorkLift # TLF1006 instructions are linked for you; these include complete hardware specs.
As far the wiring mount the Curt # C14011 does not include one and I do not recommend drilling the hitch as this will void the warranty. You can use a ring clamp mounting bracket # C58000.
If in the meantime you want to stabilize your ball mount you could use a 2-inch anti-rattle device like the Roadmaster Quiet Hitch # RM-061. You can also use this with the new Curt hitch to prevent the chance for the new hitch pin hole to become out of round.
Products Referenced in This Question
Curt Easy Mount Bracket for 4- or 5-Way Flat and 6- or 7-Way Trailer Connectors - 2" Hitch
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 6 Round
- 7 Round
- CURT
more information >
Roadmaster Quiet Hitch for 2" Trailer Hitches
- Hitch Anti-Rattle
- Standard Anti-Rattle
- Universal
- Fits 2 Inch Hitch
- Clamp Style
- Accessory Anti-Rattle
- Towing Anti-Rattle
- Roadmaster
more information >
TorkLift SuperHitch Original Trailer Hitch Receiver - Custom Fit - Class V - Dual 2" Receivers
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 1700 lbs TW
- 17000 lbs GTW
- 20000 lbs WD GTW
- 2 Inch Hitch
- 2000 lbs WD TW
- Visible Cross Tube
- TorkLift
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 1200 lbs TW
- 12000 lbs GTW
- 12000 lbs WD GTW
- 2 Inch Hitch
- 1200 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: TorkLift SuperHitch Original Trailer Hitch Receiver - Custom Fit - Class V - Dual 2" Receivers
- Shop: 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-1/2" Long Shank - Raw - 30,000 lbs
- Shop: RV Camera
- Shop: Loadstar ST235/75R15 Radial Off-Road Tire w/ 15" Aluminum Wheel - 5 on 4-1/2 - LR D
- Shop: Replacement Mounting Hardware - TorkLift SuperHitch Original Trailer Hitch Dual 2" Receivers
- Shop: Brake Controller
- Shop: Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball - 2" Drop - 15,000 lbs
- Q&A: Hardware Size Used to Install Curt # C14011 or Torklift # TLF1006 on 2000 Ford Excursion
- Shop: Reese Pro Round Bar Weight Distribution w/ Sway Control - 11,500 lbs GTW, 1,150 lbs TW
- Shop: Blue Ox SwayPro Weight Distribution w/ Sway Control - 2" Hitch - Underslung - 15K GTW, 1.5K TW
- Article: 5 Things to Know About Weight Distribution Hitches
- Search Results: bxw1503
- Video: Blue Ox SwayPro Weight Distribution w/ Sway Control for 2" Hitch Review
- Video: Checking Out the Curt TruTrack Weight Distribution System w/ Sway Control
- Video: Curt TruTrack Weight Distribution System Install - 2021 K-Z Connect Travel Trailer
- Q&A: How to Unplug a 7-Way Harness from the 7-Way on a Ford Super Duty
- Q&A: Torque Spec For The B and W Hitch Ball BWHB94004
- Search Results: bwhb94004
- Shop: Mud Flaps
- Search Results: torklift weight distribution hitch
- Shop: Blind Spot Detection
- Shop: RV Covers
- Q&A: Recommended Torque for Tightening Curt Hitch Balls to Ball Mount
- Video: Detailed Breakdown of the 2-5/16" Hitch Ball-BWHB94004
- Video: Checking Out the Curt Heavy Duty Forged Ball Mount for 2" Hitches
- Shop: RV Roof Membrane
- Search Results: spare tire mount
- Q&A: Trailer Hitch and Wiring for a 2000 Ford Excursion
- Q&A: Is There a Class V Trailer Hitch Receiver For a 2000 Ford Excursion With 2-1/2" Receiver?