Determining the Replacement Vent Cover Needed for 2005 Fleetwood Gearbox ASV Travel Trailer

Question

Question:

Here is a photo

asked by: ZACH C

0

Expert Reply:

For your 2005 Fleetwood Gearbox I have no way of knowing what vent you have. What I can do to assist is let you know there are 4 possible hinges that determine the fit. I've attached a photo to show you the differences. Once you know which one you have you will be able to choose from the available options on the linked page. The power assembly won't make a difference, but you will want to pay attention to how and where the vent cover attaches to get the same style.

expert reply by: Jason S

0

click to enlarge

Zach

3/11/2019

Here is a photo

Reply

Jason S.

3/11/2019

Thanks for the photo. The hinge you have is not one of the common ones so you can either replace the entire unit or you can use the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent - Translucent White # MA00-335001 or Translucent Smoke # MA00-335002. These vent covers come with an included mount so you can simply screw the mount to your current vent. The vent cutout will be the traditional size if you want to replace the unit. For a similar option I recommend the Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-28.

Reply

Answer 1

I have attached a photo you can use to connect the Replacement Power Switch #EJ-3520-PSW to your 3,500 lb RAM jack. We don't have a direct wiring diagram but if you notice even though the wires are the same colors they look pretty different so…

view full answer...

Answer 2

Personally I prefer the SnapPad XTRA Jack Pads #SP54FR4 over the Stromberg Carlson #SC99MR as they have been around much longer and proven themselves to be a quality product. Both these will fit 4 jacks with a 9" round landing pad.

view full answer...

Answer 3

Determining which SnapPads fit your 2022 Grand Design Solitude 380FL, the diameter of each jack foot needs to be measured and determine the shape of the foot. Note that it is not uncommon for different shapes and sizes to be used between the front…

view full answer...

Answer 4

What's up, Chuck? You can definitely use higher-rated springs for your trailer, and for that I recommend checking out the 25-1/4" Long 4-Leaf Double-Eye Spring for 4,400-lb Trailer Axles #DX95CR. Be sure to change out the leaf springs on…

view full answer...

Answer 5

Thanks for the photo, that was a huge help! You're needing 1/2 inch wire loom, which we sell by the foot as part #459075-1. I'd also use some 1/2 inch loom clamps, part #A0500 to secure the wire loom and hold it where it's supposed to…

view full answer...

Answer 6

Thank you the pictures are a great help. I recommend using the MORryde AllTrek 4000 Equalizers #MR29DR with the MORryde Suspension Upgrade Kit for Triple Axle Trailers - 3-1/8" #MR26ZR for your 2015 Keystone Carbon 327 5th wheel camper. These…

view full answer...

Answer 7

I recommend going with the Timbren Suspension Enhancement System #TFRSDJ for your 2024 Ford F-450 Super Duty because it's designed better for pickup truck-type applications. The other Timbren kit #TFRTT350J is designed more for Severe Service…

view full answer...

Answer 8

The lens on the RV Oval Porch and Utility Light #RVPL7C is held to the housing with some tabs on the lens that fit slots on the housing. To remove the lens you will need something thin and flat like a knife or small screwdriver to gently pry the lens…

view full answer...

Answer 9

The RV Propane Gas and Carbon Monoxide Detector - 12 Volt - 2 Wire - Black #RS54FR can be used to replace your 3-wire Atwood LP Detector. The third wire is just a backup power source in the event that your first power source is depleted. Typically…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Determining the Replacement Vent Cover Needed for 2005 Fleetwood Gearbox ASV Travel Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching