Axletek-12-GG Replacement Brake Assembly and Hub Recommendation

Question

Question:

Needing to replace my brakes for my RV. Can you point me to the correct brakes and drums? Thanks!

asked by: Michael W

0

Expert Reply:

The correct set of replacement brake assemblies for your AxleTek 12 inch assemblies is the kit part # AKEBRK-7-SA that you referenced. This kit is a pair of left and right assemblies that are an exact match to what you have that are also self adjusting as well.

Then if you have a 6 lug hub/drum currently the correct replacement would be the part # AKHD-655-6-EZ-K or if you have an 8 lug hub you'd need # AKHD-865-7-G-EZ-K.

expert reply by: Jameson C

0

Answer 1

Trailer brake assembly #AKEBRK-7L-SA is a 12 x 2 inch assembly with a 5-bolt mounting pattern for 5.2K to 7K axles so it will fit in place of your existing 12 inch brakes! This is the left hand assembly. The matching right hand assembly is…

view full answer...

Answer 2

The "AXLETEK-12-GG" would cross-reference to our Electric Trailer Brake Kit part #AKEBRK-7-SA but these use a five bolt mounting flange. The four bolt mounting flange is used on smaller, 10" x 2-1/4" brakes, not 12" x 2"…

view full answer...

Answer 3

We carry both the Left #AKEBRK-7L-SA and Right #AKEBRK-7R-SA Electric Trailer Brake Assemblies to replace your AXLETEK-12-GG,

view full answer...

Answer 4

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 5

We do carry the exact brakes that you need for your B12E-02 AxleTek 12-GG Axle. For the Left Assembly you will want part #AKEBRK-7L-SA and for the Right Hand assembly you will want part #AKEBRK-7R-SA. These brake assemblies are made by AxleTek and…

view full answer...

Answer 6

The Trailer Hub and Drum Assembly #AKHD-865-7-2-K is the same as the Assembly #AKHD-865-7-1-K you found but with 1/2" wheel studs versus the 9/16". We also have the Assembly #AKHD-865-7-2-EZ-K if you need the EZ Lube grease cap to access…

view full answer...

Answer 7

For hubs that have 1/2" studs, like the Easy Grease Trailer Hub and Drum Assembly for 5.2K - 7K Axles #AKHD-865-7-2-EZ-K you're looking at, you don't want to exceed 120 ft-lbs as that's the most torque this stud size can handle.…

view full answer...

Answer 8

To use the Westlake 215/75R17.5 radial tire and wheel, #LHAS701 is an 8 on 6-1/2 it may be possible to change your studs from 1/2" to 9/16" so long as the studs are drive-in (as opposed to threaded); also, the length and knurl diameter…

view full answer...

Answer 9

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 10

You're not going to have any problems mixing Dexter and Lippert components on trailer axles over 10k-lbs in the same manner as below 10k-lbs as long as the measurements on the replacement parts are the same- i.e. bearing sizes are the same, etc..…

view full answer...

Answer 11

I checked with Lippert and the Lippert 122094 hub is a 12" hub with a 6 on 5-1/2 bolt pattern for 5,200 lbs - 6,000 lbs axles. To replace the bearings you will want the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal item #BK3-100. You will need…

view full answer...

Answer 12

The closest 12v option we have to your Dometic RM1350SLMX RV refrigerator (29.5" D x 64.26" T x 33.68" W) is the Everchill RV Refrigerator w/ Freezer Drawer #WAY44FR. This fridge is 28-1/4" W x 30" D x 70-1/4" T. As far…

view full answer...

Axletek-12-GG Replacement Brake Assembly and Hub Recommendation

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching