Difficulty of Installing Optronics Trailer Light Kit # TL29BK On Small Trailer
Question:
I have a 4 way flat connector on my truck. If I buy the light kit for the small trailer I have, do you think I can put it on myself, is it fairly simple and self explainatory? Thanks
asked by: David B
0
Expert Reply:
A light kit like the Optronics Trailer Light Kit, part # TL29BK, for your trailer is a fairly simple installation if you have average mechanical abilities.
I am including a link to a video of the light kit being installed on a trailer and another video of a review on the light kit. These videos will help you with the installation process.
Also, I am including a link to a FAQ page on trailer wiring.
expert reply by: Jeff D
0
Product Page this Question was Asked From
Standard Trailer Light Kit with 25' Wire Harness
- Trailer Lights
- Tail Lights
- Stop/Turn/Tail
- Side Marker
- Side Reflector
- Rear Reflector
- License Plate
- Square
- Kit
- Surface Mount
- Non-Submersible Lights
- Incandescent Light
- 5L x 4-1/2W Inch
- Red and Amber
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Similar Expert Q&A Pages
- Instructions for Using Optronics Trailer Wiring Kit # TL29BK
- Install Video For Standard Trailer Light Kit # TL29BK
- How To Ground Trailer Tail Lights Without a Ground Wire To a Wooden Surface
- Is the 25 feet of Wire with the Standard Trailer Light Kit # TL29BK for Both Sides of the Trailer
- How Do Multiple Trailer Light Assemblies Normally Attach to Running Light Circuit.
- Trailer Light Kit for 9 by 4 Foot Trailer with No Wiring
- How to Wire the Lights in the Optronics Tail Light Kit # TL29BK
- Wiring Single Wire Clearance Lights on an Enclosed Trailer
- How to Wire a Ground Wire to a Trailer Light that Grounds Through Mounting Hardware
- Which Trailer Light Kit is Best for a Jet Ski Trailer
- Lighting Requirements for an 8-1/2-Foot Wide Trailer for Use in California
- How To Confirm Fit of Standard Trailer Light Kit with 25' Wire Harness
- Utility Trailer Light Wiring Diagram and Required Parts
- Parts Needed to Rewire Vintage Trailer
- Trailer Right Turn Signal Only Works when the Brake Lights are On
- Troubleshooting a Malfunctioning Atwood Trailer Light Kit for Use with 2004 GMC Canyon Pickup
- What Size Bulb Does Wesbar Submersible Trailer Tail Light Lens # 102641 Use
- Attaching Peterson Trailer Tail Light Kit to Harness 118304 on 2009 Toyota Sienna
- Troubleshooting Trailer Lights Going Out When the Brakes are Applied After Trailer Light Kit Install
- Troubleshooting Brake Lights that Stop Working When Running Lights Turn On
- How to Install a Trailer Wiring Harness
- Wiring Instructions for Optronics Standard Trailer Light Kit # TL29BK with 7-Way Trailer Connector
- How to Wire a Trailer for Tail Lights
- Availability of an LED Trailer Tail Light Kit that Will Fit a Snowmobile Trailer
- Trailer Tail Light Kit with Brake Lights and Turn Signals on the Same Circuit
- Troubleshooting Utility Trailer Running and Side Marker Lights Not Working
- Trailer Keeps Blowing Vehicle Running Light Fuse or Trailer Running Lights
Follow up Questions
I spent the day working on my utility trailer today, went to install the new light kit and I am having a problem getting the wires to push into the tail lights. any suggestions on how to get the wires into the push grabber holes? Thank you 75857
Make sure the ends of the wires are stripped and that you're using the upper (larger) holes for installation. It's really just a matter of pushing the stripped end of the wire into the hole until it secures into place. You may need to play around with the angle/force but it will eventually go in. 61996