Can Curt Weight Distribution System be Used with Curt Friction Sway Control
Question:
I have a trailer that currently has the Curt Friction Sway Control Item # 17200. I know a lot of weight distribution systems have sway control built in. This appears to be just the weight distribution. Will this be compatible with what I have? Will I need to move anything? Or will this simply bolt on? Thanks,
asked by: Jason
0
Expert Reply:
The Curt weight distribution system part # C17052 is perfectly compatible with your Curt Friction Sway Control Item # 17200. You'd just need to mount the smaller ball of the kit to the brackets on either side of the hitch ball of this kit and you'd be set.
I attached a picture that shows what this will look like.
click to enlarge
expert reply by: Jameson C
0
Products Referenced in This Question
Curt Friction Sway Control for Weight Distribution Systems
- Accessories and Parts
- Weight Distribution Hitch
- Sway Control Parts
- CURT
more information >
Product Page this Question was Asked From
Curt MV Weight Distribution System - Round Bar - 10,000 lbs GTW, 1,000 lbs TW
- Weight Distribution Hitch
- WD Only
- Includes Shank
- Electric Brake Compatible
- Surge Brake Compatible
- Fits 2 Inch Hitch
- 900 lbs
- CURT
more information >
Featured Help Information
Instructions
Similar Expert Q&A Pages
- Can 800 lb Spring Bars be Used With 1,000 lb Curt MV Weight Distribution
- Bar Length of Curt MV 10K Weight Distribution System
- Pole Tongue Adapter For Chain Style Hangers Weight Distribution Hitch System
- Curt MV Weight Distribution System for a 5,000 lbs Trailer and a 1999 Dodge Ram 2500
- Weight Distribution Hitch for 400-600 lbs and 800-1000 lbs Tongue Weight
- Weight Distribution Hitch Shank With 6 Drop Recommendation For A 2006 Ram 2500
- Can Trailer be Backed Up With Curt MV Weight Distribution System Installed
- Solutions for Toyota Tundra Rear Sag When Towing with Weight Distribution System
- Recommended Curt MV Weight Distribution System for Trailer with 425 Pound Tongue Weight
- Do Install Instructions Come with the Curt Weight Distribution C17052
- Replacement Spring Bar Retaining Pin and Clips For a Curt Round Bar Weight Distribution Hitch
- Weight Distribution Recommendation for Palomini 180FB
- Solution for Replacement Parts for Discontinued 10,000 Pound Draw-Tite Weight Distribution Hitch
- Are There Replacement Spring Bars for the Draw-Tite 3221 Weight Distribution System
- Weight Distribution System or New Shank with More Drop to Tow Trailer Level
- Do Round or Trunnion Bar Weight Distribution Systems Offer Better Ground Clearance
- Weight Distribution for a 1993 Chevy S-10 Blazer and 3,500 Pound Travel Trailer
- Selecting Weight Distribution/Sway Control Hitch for Travel Trailer with 300-Lbs Tongue Weight
- Shipping Weight of Curt MV Weight Distribution System # C17052
- Recommended Weight Distribution System for 6300lb Trailer w/ 550lb Tongue Weight
- Comparing Ground Clearance of Trunnion and Round Bar Weight Distribution Systems
- Do Curt C17052 and C17057 Round Bar Weight Distribution Systems Use Same Weight Distribution Head
- How Close to Vehicle Tongue Weight Capacity Can You Go
- Recommended Way To Use Weight Distribution On A Trailer That Has A Battery And Propane Tank
- How to Determine Tongue Weight of Trailer for Picking Out Weight Distribution System
- Is Sway Control Needed with Weight Distribution System on Newer Ford Truck
- Weight Distribution Recommendation for Trailers with Gross Weight of 7,000 Pounds
- Will a Curt Weight Distribution System Fit on a Trailer with an I-Beam Frame
- Do Chain Hangers Require Trailer Frame Drilling for Curt MV Weight Distribution System