Recessed Trailer D-Ring Tie Down RR5K Measurements

Question

Question:

What are the dimensions of this part. Overall size, thickness, size of hole needed to recess, etc.

asked by: Greg L

0

Expert Reply:

The D-Ring Trailer Tie Down is 6-1/2 inches x 6-1/2 inches across the back of the plate. The bolt holes are 3 inches on center apart by 3-1/4 inches (see picture). The size of the hole needed to recess the D-Ring is approximately 3-1/4 inches and the plate is 1 inch deep with the backing plate.

expert reply by: Renee B

0

click to enlarge

Answer 1

The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.

view full answer...

Answer 2

We have the Buyers Products 5/8" Forged D-Ring With 4-Hole Integral Mounting Bracket #337B40MP which is made in the USA. Most of the Tie-Down Anchors we carry are made overseas but there are a few exceptions with most of them being weld-on only.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Recessed Trailer D-Ring Tie Down RR5K Measurements

Product Page this Question was Asked From

Continue Researching