Truxedo Edge Header Stop For Chevy S-10

Question

Question:

I'm sending you some pictures of my cover hope you can help me thanks

asked by: Roosevelt G

1

Helpful Expert Reply:

Could you get me pictures of your tonneau cover so that I can identify it possibly? And which exact seals do you need?

expert reply by: Jameson C

1

click to enlarge

Roosevelt G.

11/8/2019

I'm sending you some pictures of my cover hope you can help me thanks

Reply

Jameson C.

11/8/2019

Looks like you have a Truxedo Edge or Lo Pro tonneau so the correct header stop would be the part # TX1704187. Then for a header seal you'd need the # TX1704787.

Reply

Answer 1

I went to our warehouse and took a look at the Replacement Header Seal for TruXedo Lo Pro QT, part #TX1704787. You will need to remove the seal you currently have by removing the plug on the end of the header. You may need to use something like a…

view full answer...

Answer 2

The correct replacement bulkhead weather seal for your TruXedo Lo Pro Cover is the Replacement Header Seal for TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX1704787. This seal measures 5-1/2' long and 1-1/2" wide.

view full answer...

Answer 3

The Extang #EX1032 replacement hinge that you referenced is made for Extang Trifecta and Extang eMAX folding tonneau covers as a hinge replacement. I reached out to my contact at Extang and found out that they also make the Gator covers and that this…

view full answer...

Answer 4

If you have a TruXedo Lo Pro or Edge Tonneau Cover like the one you linked to then you'll just need the Replacement Header Stop #TX1704187.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

Hey Shannon, thanks for reaching out! Sounds like you're looking for the Thule Xsporter Pro #TH500XTB-THXK3 for your 2008 Toyota Tacoma with the Deck Rail System. This is adjustable up and down as well as along the Deck Rail System so you get the…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Truxedo Edge Header Stop For Chevy S-10

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching