Can Rhino-Rack Crossbar System for RetraxONE XR Tonneau Cover Handle Rooftop Tent

Question

Question:

So I know this question has been asked before, but I have a little confusion with regards to the answer. Your video on the Rhino rack bars specifically states these bars are not a good combination for a roof top tent system, yet the experts say they are fine. So I guess my question is, I have a 2015 Ram 1500 with a retraxone xr. I would like to know if the Rhino rack system RLT600/ and 71inch aero bars will be sufficient to hold my RTT. I have also seen other sites stating the 2500 series bars do not make a suitable foundation. Any help would be appreciated.

asked by: Bryan L

0

Expert Reply:

So I reached out to Retrax to find out if the Trax Rails on the RetraxONE XR Hard Tonneau Cover # RTT-60232 had a weight capacity and they said no; the rails will accept any capacity of the roof rack.

With that in mind, you can definitely use the Rhino-Rack Vortex Crossbar System for Retrax XR Series and Mountain Top EVO-M Tonneau Covers - Black - 71" Long # RRVA180B-RRRLT600 with a rooftop tent.

The rooftop tents we carry, such as the Yakima SkyRise HD Tent for Roof Rack Crossbars # Y07436, only require the roof rack have a 165 lb capacity, and the Rhino-Rack has a 220 lb capacity as it is so you can absolutely use this Rhino-Rack system with your rooftop tent.

expert reply by: Kyle S

0

Answer 1

The 71" Rhino-Rack Vortex Crossbars for Retrax XR Tonneau Covers item #RRVA180B-RRRLT600 are the correct set for your 2022 Ram 3500. These are made for full size trucks and fit in the rails of the Retrax PRO XR. These crossbars are exactly…

view full answer...

Answer 2

Yes, to keep the Rhino-Rack Vortex Crossbars #RRVA180B-RRRLT600 from interfering with the operating handle on your Retrax XR cover you just need the Roof Rack Leg Spacer Blocks #RRQMVA25. These will raise the crossbars 25 mm (0.98") more above…

view full answer...

Answer 3

I did see the review saying they used spacers for the Rhino-Rack Vortex Crossbar System for Retrax XR Series and Mountain Top EVO-M Tonneau Covers - 71" Long #RRVA180B-RRRLT600. This system will be approximately 4-1/4" to the top of the…

view full answer...

Answer 4

I was able to confirm through my contact at Retrax that the T-channels on your 2019 Ford Raptor OEM tonneau Cover, model number VJL3Z84501A42A, share the same dimensions as the T-channels on the RetraxPRO XR Hard Tonneau Cover w/ Trax Rails…

view full answer...

Answer 5

For your 2019 GMC Sierra AT4 the Rhino-Rack Vortex Crossbar System for Retrax XR Series and Mountain Top EVO-M Tonneau Covers - Black - 71" Long #RRVA180B-RRRLT600 is the correct fit.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Scott, Really good question and yes, all of the necessary hardware that is needed for installation comes with the Rhino-Rack Vortex Crossbars for Retrax XR and Mountain Top EVO-M Tonneau Covers #RRVA180B-RRRLT600. I've added a photo for you…

view full answer...

Answer 8

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 9

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 10

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 11

Hey Peter, There unfortunately are no type of extensions for the Rhino-Rack Vortex Crossbars for Retrax XR and Mountain Top EVO-M Tonneau Covers #RRVA180B-RRRLT600. There are just spacers for it so the crossbars sit up higher from the Retrax XR…

view full answer...

Answer 12

What I would do is go out to your truck and measure out 71 inches and 65 inches on a tape measure and compare that to the width of your bed. If you think the 71 inch looks better and would suit your needs then that's what you would want to go…

view full answer...

Can Rhino-Rack Crossbar System for RetraxONE XR Tonneau Cover Handle Rooftop Tent

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching