Will 9" Round SnapPad Jack Stand Pads Fit with 2021 Grand Design Momentum 399TH

Question

Question:

Hello, Will these SnapPads fit a 2021 Grand Design Momentum 399? Thanks,

asked by: Sandy B

0

Expert Reply:

From my understanding your 2021 Grand Design Momentum 399TH 5th wheel should have the Lippert Level-Up system installed which uses a 9" round foot plate for the jacks that will match up perfectly with the SnapPad Jack Stand Pads # SP54FR6.

expert reply by: Jon G

0

Answer 1

For your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC675817 or #LC358590 you need to reset the leveling memory. The “Zero Point” is the programmed point that the trailer will return to each time the Auto Level feature is used…

view full answer...

Answer 2

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 3

We do carry the 9" SnapPad Jack Stand Pads in a 6-pack as part #SP54FR6!

view full answer...

Answer 4

SnapPads like the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 6 Item #SP54FR6 can be taken off and on as needed so you won't have to keep replacing them every time you need to take them off.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Having the puck system is a great feature. If you ever plan on loading the bed with mulch, sand or rock you'll quickly find that having rails permanently bolted to the bed floor is a real pain. Not only that, but the pucks look a lot better.…

view full answer...

Answer 12

Great questions! Reese actually makes the OEM puck system for Ford so if the 2022 F-250 is cheaper by a lot then I recommend going that route and installing the Under-Bed Rail and Installation Kit #RP87FR. The only thing you'll really be missing…

view full answer...

Will 9" Round SnapPad Jack Stand Pads Fit with 2021 Grand Design Momentum 399TH

Product Page this Question was Asked From

Continue Researching