Solution for Northern Breeze RV Roof Vent with Bad Motor

Question

Question:

Need vent fan motor...Ventline, VL801-001, 12vdc, 5.0A. Old motor has 3 mounting flanges. For model V2525, Northern Breeze bathroom vent fan in Jayco 33 ft travel trailer.

asked by: Don

0

Expert Reply:

The motor for the V2525 Northern Breeze fan is unfortunately not available as a replacement part. If the motor is bad then the best solution is to replace the entire vent unit with part # V2094SP-34 which has the 12V fan and a manual lift. You will also need the install kit # 344270KITW which comes with seat and mounting hardware.

expert reply by: Jameson C

0

Answer 1

I determined that your Ventline exhaust fan v2525 is a northern breeze model and unfortunately we do not carry a replacement motor. I recommend Replacement Roof Vent for MaxxFan Plus Roof Vent w/ 12V Fan - Powered Lift - 10 Speed - Smoke Item…

view full answer...

Answer 2

To replace the Northern Breeze V2425 vent on your 2006 Jayco I recommend the Ventline Ventadome #V2094SP-30 which is a standard manual 12V vent with a white lid - this should be pretty identical to what you currently have. Be sure to pick up the…

view full answer...

Answer 3

For your 2010 Royal Cargo trailer, you will have to check your current vent for a manufacturer. If you have a Ventline Ventadome or a Northern Breeze roof vent then the Replacement Plastic Operator Knob is #BVD0421-15 and the Replacement Metal Dome…

view full answer...

Answer 4

The Replacement Gear Motor with Pinion Gear for Ventline Ventadome Trailer Roof Vent #BVB0601-00 or just the Replacement Plastic Gear for Ventline Ventadome Trailer Roof Vent - Dome Motor Gear #BVD0121-00 is what you need to lift the dome.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Solution for Northern Breeze RV Roof Vent with Bad Motor

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching